Teledyne T3PSX3200P Series User manual

  
   
      

This manual contains proprietary information, which is protected by
copyright. All rights are reserved. No part of this manual may be
photocopied, reproduced or translated to another language without
prior written consent of Teledyne LeCroy company.
The information in this manual was correct at the time of printing.
However, Teledyne LeCroy continues to improve products and
reserves the rights to change specification, equipment, and
maintenance procedures at any time without notice.

Table of Contents
3
Table of Contents
SAFETY INSTRUCTIONS .................................................. 4
Safety Symbols .........................................................4
Safety Guidelines......................................................5
Power cord for the United Kingdom ..........................8
OVERVIEW ...................................................................... 9
Key Features ........................................................... 10
Front Panel ............................................................. 12
Rear Panel .............................................................. 19
GETTING STARTED ........................................................ 21
Start Up .................................................................. 22
Load Connection..................................................... 23
Turning the Output On/Off ..................................... 24
APPENDIX ..................................................................... 25
Specifications ......................................................... 25

SAFETY INSTRUCTIONS
4
SAFETY INSTRUCTIONS
This chapter contains important safety
instructions that you must follow during
operation and storage. Read the following before
any operation to insure your safety and to keep
the instrument in the best possible condition.
Safety Symbols
These symbols may appear in the manual or on the instrument.
WARNING
Warning: Identifies conditions or practices that
could result in injury or loss of life.
CAUTION
Caution: Identifies conditions or practices that
could result in damage to the T3PSX3200P series
or to other properties.
DANGER High Voltage
Attention Refer to the Manual
Protective Conductor Terminal
Earth (ground) Terminal
Do not dispose electronic equipment as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased.

SAFETY INSTRUCTIONS
5
Safety Guidelines
General
Guideline
CAUTION
Do not place any heavy object on the unit.
Avoid severe impact or rough handling that
leads to damaging the unit.
Do not discharge static electricity to the unit.
Do not block the cooling fan opening.
Do not perform measurements on circuits that
are directly connected to mains power.
Do not disassemble the T3PSX3200P series
unless you are qualified.
Do not connect the measuring terminals of the
unit directly to supply mains.
Note: Measuring terminals of the T3PSX3200P
series have no rated measurement category
(CAT) per IEC/EN 61010-1:2010.
Power Supply
WARNING
AC Input voltage range:
100V/120V/220V/230V ±10%
Frequency: 50Hz/60Hz
To avoid electrical shock connect the protective
grounding conductor of the AC power cord to
an earth ground.
Fuse
WARNING
Fuse type: 100V/120V：T6.3A/250V，
220V/230V：T3.15A/250V
To prevent fire, replace the fuse only with the
specified type and rating.
Disconnect the power cord before replacing the
fuse.
Make sure the cause of fuse blowout is fixed
before replacing the fuse.

T3PSX3200P Series Quick Start Guide
6
Cleaning the
power supply
Disconnect the power cord before cleaning the
power supply.
Use a soft cloth dampened in a solution of mild
detergent and water. Do not spray any liquid
into the power supply.
Do not use chemicals containing harsh products
such as benzene, toluene, xylene, and acetone.
Operation
Environment
Location: Indoor, no direct sunlight, dust free,
almost non-conductive pollution (Note below)
Relative Humidity: < 80%
Altitude: < 2000m
Temperature: 0°C to 40°C
(Pollution Degree) EN 61010-1:2010 specifies pollution degrees
and their requirements as follows. The T3PSX3200P series falls
under degree 2.
Pollution refers to “addition of foreign matter, solid, liquid, or
gaseous (ionized gases), that may produce a reduction of
dielectric strength or surface resistivity”.
Pollution degree 1: No pollution or only dry, non-
conductive pollution occurs. The pollution has no influence.
Pollution degree 2: Normally only non-conductive pollution
occurs. Occasionally, however, a temporary conductivity
caused by condensation must be expected.
Pollution degree 3: Conductive pollution occurs, or dry,
non-conductive pollution occurs which becomes conductive
due to condensation which is expected. In such conditions,
equipment is normally protected against exposure to direct
sunlight, precipitation, and full wind pressure, but neither
temperature nor humidity is controlled.
Storage
environment
Location: Indoor
Relative Humidity: < 70%
Temperature: -10°C to 70°C

SAFETY INSTRUCTIONS
7
Checking the AC
Voltage
CAUTION
Before the power is turned on,
confirm that the input power
supply meets the following
conditions:
100V/120V/220V/230V ±10%，
50/60Hz
AC SELECTOR
220V230V 120V 100V

T3PSX3200P Series Quick Start Guide
8
Power cord for the United Kingdom
When using the power supply in the United Kingdom, make sure
the power cord meets the following safety instructions.
NOTE: This lead/appliance must only be wired by competent persons
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in accordance with the
following code:
Green/ Yellow:
Earth
Blue:
Neutral
Brown:
Live (Phase)
As the colours of the wires in main leads may not correspond with
the coloured marking identified in your plug/appliance, proceed
as follows:
The wire which is coloured Green & Yellow must be connected to
the Earth terminal marked with either the letter E, the earth symbol
or coloured Green/Green & Yellow.
The wire which is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Blue or Black.
The wire which is coloured Brown must be connected to the
terminal marked with the letter L or P or coloured Brown or Red.
If in doubt, consult the instructions provided with the equipment
or contact the supplier.
This cable/appliance should be protected by a suitably rated and
approved HBC mains fuse: refer to the rating information on the
equipment and/or user instructions for details. As a guide, a cable
of 0.75mm2should be protected by a 3A or 5A fuse. Larger
conductors would normally require 13A types, depending on the
connection method used.
Any exposed wiring from a cable, plug or connection that is
engaged in a live socket is extremely hazardous. If a cable or plug is
deemed hazardous, turn off the mains power and remove the cable,
any fuses and fuse assemblies. All hazardous wiring must be
immediately destroyed and replaced in accordance to the above
standard.

OVERVIEW
9
OVERVIEW
This chapter contains a brief introduction to
T3PSX3200P series including the main features
and an overview of the front and rear panel.
Key Features ........................................................... 10
Front Panel ............................................................. 12
Rear Panel .............................................................. 19

T3PSX3200P Series Quick Start Guide
10
Key Features
Features
Multiple Outputs:
T3PS13206P: 32V/6A x 1
T3PS23203P: 32V/3A x 2 (CH1/CH2)
T3PS33203P: 32V/3A x 2 (CH1/CH2)
1.8V/2.5V/3.3V/5V/5A x 1(CH3)
USB Port Output: 3A
T3PS43203P: 32V/3A x 2 (CH1/CH2)
5V/1A x 1(CH3), 15V/1A x 1 (CH4)
Constant voltage and constant current operation
(CV/CC).
Low noise, thermostatically controlled fan.
4.3 inch TFT display.
Operation
Digital panel control.
Output on/off control (ON/OFF), and each
channel can be controlled separately.
Digital voltage and current settings. (Key &
Encode)
10 groups of save/recall settings and 2 groups of
power-on settings.
10 groups of save/recall Sequence.
10 groups of save/recall Delay.
10 groups of save/recall Record.
CH1/CH2 workable in Load Mode
7 types display modes available with 5 contents
and 2 waveforms respectively
Input/Output terminal (Control I/O)
Alarm buzzer (BEEP).
Key lock function (LOCK).
Multiple remote control interfaces (standard:
RS232, USB, LAN)

OVERVIEW
11
Protection
Features
Overvoltage and overcurrent protection (OVP/
OCP)
Overtemperature protection (OTP).
Polarity Reverse Protection
Overload Protection (OPP in Load mode)
Interface
Remote Control RS-232
USB remote control.
Control I/O
LAN remote control

T3PSX3200P Series Quick Start Guide
12
Front Panel
0 - 32V , 3A
Memory
0 - 5V , 1A
CH3
CH2CH1
ON/OFFON/OFF
Advance
CH3
ON/OFF
Lock
ALL
ON/OFF
Enter
8
5
2
9
6
3
PARALLEL OUTPUT
MASTER
0 - 32V , 3A
CH4
System
ON/OFF
CH2GND
COM SERIES OUTPUT
SLAVE
CH1CH4
0 - 15V , 1A
0
7
4
1
T3PS43203P
Programmable DC Power Supply
32V 3A
LCD
Number
pad
Scroll wheel/
Arrow keys
Function
keys
USB host
Front panel
output terminals
Power button
*The panel above is the example of T3PS43203P.
Display
Display
Interface
T3PS43203P model

OVERVIEW
13
Channel
distribution
Channel number and distribution vary by models
with different colors identifications:
CH1: Yellow CH2: Blue CH3: Pink CH4：Green
CH1 is master and CH2 becomes yellow under
tracking series and tracking parallel modes.
Single channel
display
Channel/
Status
Power
display
V/I
setting
Voltage display
Current display
OVP/OCP
setting area
Channel no.
Color of channel remains the original when not
being set.
Color of channel blinks between the original and
orange when being set.
Channel status
Display active channel state
Power supply: CH1/CH2/CH3/CH4: green or
red
Load Mode: CH1/CH2: orange
Voltmeter
Indicators
Displays the output voltage with up to 6 digits of
resolution. The default units are Volts (V).
CH1：
CH2：
CH3：(T3PS43203P)
(T3PS33203P)
CH4：

T3PSX3200P Series Quick Start Guide
14
Ammeter
Indicator
Displays the output current with up to 5 digits of
resolution. The default units are ampere (A).
CH1:
CH2：
CH3：(T3PS43203P)
CH4：
Setting Display
Displays the voltage and current settings.
CH1/CH2/CH3/CH4:
CH3(T3PS33203P) displays setting of voltage only
Display OVP/OCP settings
CH1/CH2/CH3/CH4:
The CH3 OVP of T3PS33203P is a fixed value
(approx. 5.5V), non-configurable and with only on
or off switch available for user. OCP is available
only for USB output port (approx. 3.1A)

OVERVIEW
15
Status
Indicator
Display the set function/remote control interface
: The active channel under setting status
: The status of OTP protection mode
: The status of USB flash drive connected
: USB remotely disconnected
: USB remotely connected
: The status of control I/O connected
Others: when operating in the series/parallel
tracking mode, the corresponding SER/PAR icons
appear on the display.
when Sequence/Delay/Monitor/Recorder is
activated, the corresponding SEQ/DLY/MON/
REC icons appear on the display.
Function Keys
Power Button
Turns the power on or off.
On:
Off:
Channel select
buttons
CH2CH1 CH3CH4
Each channel has its own button
and promptly switchable among
CH1-CH4 setting.
Output buttons
Individual output
ON/OFF
The ON/OFF button is
operational individually by each
channel. The Output key will light
up when the output is on.
ON:
ON/OFF ON/OFF
Output all
All ON:
ALL
ON/OFF
ALL
ON/OFF
Number pad
Enter
8
5
2
9
6
3
0
7
4
1
For parameter value setting

T3PSX3200P Series Quick Start Guide
16
Scroll wheel &
Arrow keys
Scroll wheel is used to set each
parameter value, whilst arrow
keys are used for parameter,
menu selection and
voltage/current fine adjustment.
It is used to switch or operate the
displayed waveforms under
diagram display mode.
Function keys
The 6 function keys (F1-F6) display varied
functions per different opertations.
System key
System
It is used to set functions including
Interface, Beep, Backlight, etc.
Advance key
AdvanceSystem
It is used for certain advanced functions
like Sequence, Delay, Monitor, Recorder,
etc.
Memory key
Memory
Advance
It is used to operate several functions
including save and recall, etc., for set
parameters.
Lock key
Memory Lock
It is used to disable all the panel keys
except for the Output key.
Unlock
Press the F6 button to unlock, which can
disable remote control and return to panel
operation.

OVERVIEW
17
Terminals
CH1 terminal
MASTER
0 - 32V , 3A
CH1
Power output terminal or load input
terminal
CH2 terminal
SLAVE
0 - 32V , 3A
CH2
Power output terminal or load input
terminal
CH3 terminal
0 - 5V , 1A
CH3
Power output terminal
3A MAX
Power output terminal (T3PS33203P
only)
Warning: The output current from the 2 terminals should
Not exceed 5A for T3PS33203P.
CH4 terminal
CH4
0 - 15V , 1A
Power output terminal
GND terminal
GND
Ground terminal
Voltage
feedback
terminal
(SENSE)
SS
Sense terminal of power output (for
T3PS13206P only)

T3PSX3200P Series Quick Start Guide
18
Panels of other models:
T3PS13206P
S
Enter
8
5
2
9
6
3
Advance Lock
Memory
On / Off
S GND
0 - 32V , 6A
Programmable Power Supply
32 V 6 A
0
7
4
1
System
GPP-1326
T3PS13206P
Programmable DC Power Supply
32V6A
T3PS23203P
0 - 32V , 3A
Enter
5
2
6
3
Advance Lock
Memory
ON/OFF ON/OFF
CH1 ALL
ON/OFF
8 9
MASTER
0 - 32V , 3A
CH1 CH2GND
COM SERIES OUTPUT
PARALLEL OUTPUT
SLAVE
Programmable Power Supply
0
4
1
System
GPP-2323
32 V 3 A
7
T3PS23203P
Programmable DC Power Supply
32V 3A
CH2
T3PS33203P
System
ON/OFF
CH2
SLAVE
0 - 32V , 3A 3A MAX5V/3.3V/2.5V/1.8V , 5A
Lock
ON/OFF
Enter
Advance Memory
ON/OFF ON/OFF
ALL
CH3
8
5
2
9
6
3
0 - 32V , 3A
COM SERIES OUTPUT
PARALLEL OUTPUT
CH1
MASTER
0
CH1
GND
GPP-3323
32 V 3 A
Programmable Power Supply
7
4
1
T3PS33203P
Programmable DC Power Supply
32V3A
CH2 CH3

OVERVIEW
19
Rear Panel
LCD
Alternate
input switch
USB portHeat sink fan
Control I/O port
To avoid electric shock the power cord protective grounding conductor
For continued fire protection. Replace fuse only with 250V fuse of the
No operator serviceable components inside.
LAN
SER.NO. LABEL
Control I/O
must be connected to ground.
specified type and rating.
Do not remove covers. Refer servicing to qualified personnel.
WARNING
100V T 6.3A
RS-232
50/60 Hz
420 WATTS
AC
230V 250V
T 3.15A
220V
120V 250V
BEFORE REPLACING FUSE
DISCONNECT POWER CORD
REPLACE FUSE
FUSE RATING
AS SPECIFIED
AC SELECTOR
220V230V 120V 100V
AC input
socket and
line fuse
LAN port
Items
Description
Alternate
input switch
AC SELECTOR
220V230V 120V 100V
AC voltage selection:
100V/120V/220V/230V ±10%,
frequency 50/60Hz
AC input
socket and
line fuse
The AC input accepts
100V/120V/220V/230V AC. The
frequency is 50Hz/60Hz.
Fuse: 100V/120V: T6.3A/250V,
220V/230V: T3.15A/250V,
slow-blow type
USB port
USB device port for remote control.
LAN port
LAN
LAN port for remote control.

T3PSX3200P Series Quick Start Guide
20
RS 232 port
RS-232
RS232 port for remote control.
Control I/O
port
Control I/O
5 ports in all for input/output control.