TeleEye DM870 User manual

DM870/DM880 High Speed Dome
Before using the product, please read this manual carefully.

Index
Welcome.............................................................................................................................................1
Declaration...........................................................................................................................................2
InstallationPreparation..........................................................................................................................3
InstallatonType Guide...........................................................................................................................4
In-CeilingMount..................................................................................................................................5
Wall Mount..........................................................................................................................................8
CornerMount.....................................................................................................................................11
PoleMount........................................................................................................................................14
PendentMount...................................................................................................................................17
ParapetMount...................................................................................................................................20
Operation..........................................................................................................................................23
A.OperationInstruction.............................................................................................................23
B.MenuTree............................................................................................................................24
C.MenuOperation..................................................................................................................25
1.SystemInformation.........................................................................................................26
2.Lens Parameters.............................................................................................................30
3.Camera Parameters........................................................................................................32
4.Pan/TiltParameters.........................................................................................................34
5.Auto RunningSetup........................................................................................................35
6.TimerRunningSetup........................................................................................................39
7.PrivacyMasking.............................................................................................................40
8.Alarm Setup...................................................................................................................42
AppendixI: DIPSwitch&Jumper Settings...........................................................................................43
AppendixII: WireDiameter&TransmissionDistanceComparisonChart................................................49
AppendixIII:RS485Bus BasicKnowledge.........................................................................................50
AppendixIV:LightningProof&Surge Proof.......................................................................................52
AppendixVI: TroubleShooting............................................................................................................53
AppendixVII :Specification................................................................................................................54

-1-
Thank you forpurchasingourHIGHSPEEDDOME.
This series speeddomeis newlyupgradedwithAMPconnectorforeasierinstallation andblacklinerfordiscreet
surveillance.Thepowerful functions makeitastate-of-the-art speeddome,andit willfulfillyour widerangeprofes-
sional securitysurveillance need.
Features:
lBackup Memory, parametersmemoryis designedtolocateonthePCB board inthehousing, settingswill remain
whenchangePTZmodule.
lAutoruning,runs theassignedfunctionautomaticallyafteraperiod ofidling.
lTimerruning,8functionschedules.
l220presets, 4sequenceswith up to32 presetseach,4patternswithmin.180secondseach,4pannings,8
regions.
lOn screencompass andpan/tiltdegrees indicator.
lUpto 8 privacymasks.
lWith dome,preset, pattern, panningand regiontitles,thetitles canbeset tonot display, displayordisplayfor a
period oftime.
lColor/Monoauto,manualorswitchat asettime.
lWith4000Vvideo, data,powerlightningproof and surgeproof.
lHi-accuracymotor driveswith 0.1 degreepresetaccuracy, min. 0.1degreemovingwithout anyvibration.
l360degreecontinuouspanning, 90 degreetilt withautoflipping.
lBuilt in DSPcamera, with autofocus,auto BLC, autolight control, autowhitebalanceetc. functions.
lInformativeChinese/EnglishOSD menu,allthefunctions canbeset via OSDmenu.
Welcome

-2-
This equipmenthas beentestedand foundtocomplywiththelimits foraClass Adigital device, pursuant to part 15 of
FCCrulesand EuropeanUnion89/336/EECdirectiveand its latestamendedversion.Theselimits aredesignedto
providereasonableprotection against harmful interference when theequipmentis operated in acommercial environment.
Thisequipment generates,uses,andcanradiateradio frequencyenergy and, ifnot installedand usedinaccordance
withtheinstructionmanual, maycauseharmfulinterferencetoradiocommunications.Operation ofthisequipmentin
aresidential areaislikelytocauseharmfulinterference inthat casetheuser will berequiredtocorrect theinterference
athis own expense.Modificationsnotexpresslyapprovedbythemanufacturercouldvoidtheuser sauthorityto
operatetheequipmentunder CE and FCC rules.
Precautions:
1.Onlyqualifiedand experiencedperson cancarryonthisinstallation.
2.Alwaysconformtonationalandlocalsafetycodesduring installation.
3.Usereliabletools only, poor quality tools maycausedanger. e.g.ladder.
4. Do install thespeeddometo appropriateenvironment(Pleasereferto thechartbelow). Thisproductconformsto
IP66 standardas specifiedin “HousingProtection Classification (IP code)”.
5.Checkthespace and toughness of thesitebeforeinstalling. It shouldbeabletobear 4 times theweight of thedome
anditsaccessories.
6.Keep all theoriginal domepackagematerials incaseof futurerepackingand transporting.
Warnings:
1. DO NOT install this speeddomeinhazardous places wherecombustibleor explosivematerials arestoredorused.
2. DONOT install indoor domein outdoor environment.
3. This speeddomerunson24V AC. DO NOT connect higheror lowervoltageto it.
4. DO NOT turnpower onbeforecompleting installation.
5. DO NOT disassembleanypartof theitems.
6.Usesoft towelto cleanthedown cover whennecessary. DONOT usecaustic detergent.
7. To protect CCD, avoid facingthecameradirectlytothestronglight.e.gthesun.
ModelIndoorOutdoor
MaximumTempRange -10 oC~+50oC-40 oC~+60oC
Humidity<90%<90%
AirPressure86~106KPa86~106KPa
PowerSupplyAC24V/1.25A,50/60HzAC24V/2.5A,50/60Hz
Declaration

-3-
InstallationPreparation
ToolsLists:
You mayneedfollowing tools for theinstallation:
Screwsandnuts,screwdriver,Smallslottedscrew
driver, Wirecutter,Ladder,Drill,Saw.
Cables:
VideoCoaxialCable
The videocoaxial cableshouldbe:
1) 75Ohmimpedance.
2) Solid copper wire.
3)95% braidedcoppershield.
Checkthemaxtransmission distance referring to
thechartbelow.
InternationalGaugeTransmissionDistance(Max.)
RG59/U750ft(229m)
RG6/U1,000ft(305m)
RG16/U1,500ft(457m)
RS485 Cable
0.56mm (24AWG) twistedpair smaxi-
mum transmissiondistancesareasfollows.
Baud RateTransmissionDistance(Max.)
2400bps5,906ft (1800m)
4800bps3,937ft (1200m)
9600bps2,625ft (800m)
DIP switchesand jumperssettings
Pleaserefer toappendix I tosetthefollowings:
Protocol and Baud rate
Domeaddress
Videocabletype
Alarmoutput method
RS485 terminationresistor
1
2
3
4
5
67
8
9
10
12
11
1316
15
14
19
18
17
20
21
23
22
WiringDiagram foralarm,video
&RS485andPower
1 Alarm Input1 16 Video Output
2 Alarm Input2 17 Video Ground
3 Alarm Input3 18 RS485+
4 Alarm Input4 19 RS485-
5 Alarm Input5 20 Reserved
6 Alarm Input6 21 Reserved
7 Alarm Input7 22 Reserved
8 Common Port 23 Reserved
9Alarm Output1
10 Alarm Output1
11 Alarm Output2
12 Alarm Output2
13 24V AC
14 Ground
15 24V AC
NOTE: UseRS485 distributor if you needto trans-
mit further.Tolearnmoreabout RS485, pleasere-
fer toappendix III.

-4-
Bracketmount domehas indoor typeandoutdoor type. Comparingtoindoor type,outdoor typehasextrasun-shield
housing, temperaturesensor and heater.Outdoor typeconforms toIP66 standard.
WARNING: DO NOTinstall indoor domeinoutdoor environment.
In-ceilingMount (Page5~7)
INSTALLATION TYPEGUIDEINSTALLATON TYPEGUIDE
InstallationType Guide
3.PoleMount (Page14~16)
2.CornerMount (Page11~13)
4.Pendant Mount (Page17~19) 5.Parapet Mount (Page20~22)
BracketMount
1.Wall Mount (Page8~10)
Twomainkindsofinstallation areavailablefor highspeed
dome:
1) In-ceilingMount
2)Bracket Mount
Thereare5bracketoptionsfor bracket mount:
1)Wall Mount
2)CornerMount
3)PoleMount
4)Pendant Mount
5)Parapet Mount
NOTE: Installationsiteshould beableto withstandat
least4timestheweight ofthedome.
TypeWeight(kg/lb)
IndoorCeiling Dome2.43kg (5.35lb)
OutdoorDome
(excluding bracket)
3.78kg (8.33lb)
PendantBracket1.53kg (3.37lb)
Wall Bracket1.25kg (2.75lb)
CornerBracket1.90kg (4.19lb)
Pole Bracket 1.20kg (2.64lb)
ParapetBacket6.50kg(14.33lb)

-5-
In-CeilingMount
2Cutthecircle off
Useasawor propertoolto cut offthecircle.
NOTE: MAKE SUREthediameterofthecircleis
225+2mmbeforecuttingthecircleoff.
1Draw acircleonceiling
Takethepaper pattern(accessory)as atemplateto
drawapattern ontheceiling. Thepaperpattern s
diameteris 225mm.
3Unfastenthepower boardholder
Loosenthebolt toswing awaythepowerboard
holder.
PowerBoardHolder
Power Board
Bolt
Installationrequirements:
1. Thethickness of theceiling should beless than42mm.
2.Theceilingshould beableto bear4 timestheweight
ofthespeeddome.
3. Upperspaceshould beatleast20cmhigh.
2252

-6-
7Install housing
Pushhousing intoceiling and let theclipsstretch
out.Finally,screwthethreeclipstotightenthe
housing.
NOTE: Useevenstrengthtoadjustthethree clips,
or itmaydistorttheshapeofthehousing.
6Adjust clips
Adjust theheightofthethree mounting clips.Swing
thethreemounting clips to cling themtohousing.
MountingClip
Mounting Clip
Mounting Clip
5Connect cables
Insertcablesinto correspondingsocketson power
board.Aftercompleting cableconnection, swing the
power board holderback and thenturnon thepower.
TheredLED will light up.Turn offthepower after
checking. If not lightup, checkthecableconnection.
NOTE: Therearesignsforeach port. connectcables
aspictureshowedin page3.PleaseMAKE SURE
powerisoff beforedoingconnection.
4Preparecables
Preparewiring and thenputPower/RS485/Video
cablesthrough water-proof connectorand thetop
ofhousing.Finally,turntheconnector intothetop
holeofthehousing.
Waterproof
Connector
-
VideoRS485
&
VideoRS485&
Power
Power
Bolt
Alarm
Alarm
RedLED
Ceiling Thickness
Mounting Clip

-7-
8Set domeID,baudrate and protocol
SetdomeID, baud rateandprotocolviaDIPswitches
(pleasereferto APPENDIXI).Removethetwo
sponges.
9Install blackliner and Pan/Tilt Module
Pushtheblack liner intothetwo lockingtabs. Align
thepan/tilt moduletothetwo clips, redtored, black
to blackand matchtheholesin pan/tilt moduleand
thetwo guidepoles.Gentlypushthemoduleupward
until youheartwoclicksound.
NOTE: BesuretheAMPsockets arecleanwithout
any dust. DONOTforget toremovethelens cover.
10Installdowncover
Fixthesafetychainon housing.Thesafetychain
prevents thedown coverdropping down. Matchthe
clasps and mountingholes thenturnthedown cover
frameanti-clockwise.
NOTE:
lLetthesafetychaininsidethearcgrooveof
thedowncover, otherwiseitmayscratchthelens.
lIf youfound difficult tofit in thedown cover,
tryreadjustingthethreeclips.
SafetyChain
Mounting Hole
Clasp
Tab
BlackLiner
P/T Module
Tab
AMP Socket
RedLable
RedClip
Guide Pole
SW1 SW2
SPONGE
SPONGE
SW2
SW1

-8-
1Mark screwspositions
Takethebracket baseasthetemplatetomark the
screws positions on wall. Drilltheholesand put ex-
pansionscrewsinside.
Wall Mount
2Install bracket
Put Power/RS485/Video cablesthrough thecavity
ofbracket, andtheninstallbracketon wall.
NOTE: Putcables through thewall orasidethe
bracket.
84
140
M8
Installationrequirements:
Thewall mounting surfacemust befirmenough to
bear4timestheweight ofthespeeddome.

-9-
5Connectcables
Insertcables into correspondingsockets on power
board.After completing cableconnection, swing the
powerboardholderback and then turnon thepower.
TheredLED will light up. Turn off thepower after
checking.Ifnot lightup, checkthecable
connection.
NOTE: Therearesignsfor eachport.Pleasecon-
nectcablesaspicture showedin page3. Please
MAKE SURE powerisoff beforedoing connection.
6Set domeID,baud rateand protocol
SetdomeID, baudrateandprotocol viaDIPswitches
(pleaserefer toAPPENDIXI). Removethetwo
sponges.
4Installhousing
Insert cablesthroughtheholeat thetopof thehousing
Applywater-proof tapetothehousingthread. Then
turnthehousing ontothewallmountbracket and
retaintheconnectionwith anM4 screw.
NOTE: Applysiliconetothegapbetweenbracket
andwall inthecaseofoutdoor dome.
3Unfasten thepower boardholder
Loosenthebolt and swing awaythepowerboard
holder.
SPONGE
SW2
SW1
SW2
SW1
SPONGE
M4
Tape
Bolt
Alarm
Power
Video&RS485

-10-
7Down cover preliminary installation
AttachthesafetychainwithanM3 nutaspicture
shows. Thesafetychain preventsthedowncover
fromdropping down.
NOTE: Connect theheaterplug intothesocket inthe
caseof outdoordome.
8Install black liner and Pan/Tilt Module
Pushtheblackliner intothetwo locking tabs.Align
thepan/tilt moduletothetwo clips, redtored, black
to blackand matchtheholes inpan/tilt moduleand
thetwo guidepoles.Gentlypushthemoduleupward
until youheartwoclicksound.
NOTE: BesuretheAMPsockets arecleanwithout
dust.DO NOT forgetto removethelens cover.
9 Install down cover
Loosenthe twoM4screws ondowncover ring.
Applylubricant totheO-ring tomakedown cover
easiertoslipin. Push upwardthedowncoverinto
thehousing and thenfastendown coverwithtwo
M4 screws.
Red Lable
AMP Socket
RedClip
M4
Lube
M4
Connectthe two
ports oftheheater
Safety Chain
M3Nut

-11-
CornerMount
2Install base
Put Power/RS485/Videocables throughtheholeof
cornerbaseanduseM8nutsto fastencorner base
onthemountingsurface.
NOTE: Putcables through thewall or asidethe
cornerbase.
1Mark screwspositions
Takethebracketbaseasthetemplate tomarkthe
screws positionson wall. Drill theholes andput
expansionscrews inside.
Installationrequirements:
Thecornermounting surface must befirmenoughto
bear4timestheweight ofthespeeddome.

-12-
6Connect cables
Insertcablesinto correspondingsocketson power
board.Aftercompleting cableconnection, swing the
power board holderback and thenturnon thepower.
TheredLEDwilllightup. Turnoff thepowerafter
checking. If not lightup, checkthecableconnection.
NOTE: Therearesigns foreachport.Pleasecon-
nectcablesaspictureshowedin page3.Please
MAKE SURE power is off beforedoing connection.
3Install bracket
Put cablesthroughthecavityofbracket andfasten
bracket onbase.
4Unfasten thepower boardholder
Loosenthebolt and swing awaythepowerboard
holder.
5Installhousing
Insert cables through theholeat thetop of thehous-
ingApply water-proof tapetothehousingthread.
Thenturnthehousing ontothewallmount bracket
andretaintheconnectionwith anM4 screw.
NOTE: Apply siliconeto thegapbetweenbracket
andwall inthecaseofoutdoor dome.
Bolt
Tape
M4
Alarm
Power
Video&RS485

-13-
8Downcoverpreliminaryinstallation
Attachthesafetychain withanM3screwas
pictureshows.Thesafetychainpreventsthe
down coverfromdropping down.
NOTE:Connecttheheaterplug into thesocketin
thecaseof outdoordome.
7Set domeID,baudrate and protocol
SetdomeID, baud rateandprotocolviaDIPswitches
(pleasereferto APPENDIXI).Removethetwo
sponges.
10 Install down cover
Loosenthetwo M4screws on down coverring.
Applylubricant totheO-ring tomakedown cover
easiertoslipin. Push upwardthedowncoverinto
thehousing and thenfastendown coverwithtwo
M4 screws.
SPONGE
SW2
SW1
SPONGE
SW1 SW2
9 Install blackliner andPan/TiltModule
Pushtheblackliner intothetwo locking tabs.Align
thepan/tilt moduletothetwo clips, redtored, black
to black andmatchtheholesin pan/tiltmoduleand
thetwo guide poles.Gently pushthe moduleup-
warduntilyouheartwoclicksound.
NOTE: BesuretheAMPsockets arecleanwithout
dust.DO NOT forgetto removethelens cover.
Lube
M4
Connectthe two
portsoftheheater
SafetyChain
M3Nut
Red Lable
Red Clip
AMP Socket

-14-
1Install base
Mount thepoleadaptortothepolewith two mount-
ing clamps. Put Power/RS485/Videocablesthrough
thecentralholeofthebracket base,and thenfix it
around thepole.
PoleMount
2Install wallmountbracket
Put cables through thecavity of wall mount bracket
andfasten itonbase.
M8
M4
Installationrequirements:
Theoutsidediameter ofthepolemust beintherange
of130-150mm(5.12~6inches).

-15-
5Connect cables
Insertcablesinto correspondingsocketson power
board.Aftercompleting cableconnection, swing the
power board holderback and thenturnon thepower.
TheredLED will light up.Turn offthepower after
checking. If not lightup, checkthecableconnection.
NOTE: Therearesigns foreachport.Pleasecon-
nectcablesaspicture showedinpage3.Please
MAKE SURE power is off beforedoing connection.
6Set domeID,baud rateand protocol
SetdomeID, baud rateandprotocolviaDIPswitches
(pleasereferto APPENDIXI).Removethetwo
sponges.
3Unfasten thepower boardholder
Loosenthebolt and swing awaythepowerboard
holder.
4Installhousing
Insert cables through theholeat thetop of thehous-
ingApply water-proof tapetothehousingthread.
Thenturnthehousing ontothewallmount bracket
andretaintheconnectionwith anM4 screw.
NOTE: Apply siliconeto thegapbetweenbracket
andwall inthecaseofoutdoor dome.
SPONGE
SW2
SW1
SPONGE
SW2
SW1
Alarm
Power
Video&RS485
Bolt
Tape
M4

-16-
7Downcoverpreliminaryinstallation
Attachthesafety chainwithanM3 nut aspicture
shows. Thesafetychainprevents thedowncover
fromdropping down.
NOTE:Connect theheater plug intothesocket in
thecaseof outdoordome.
8 Install blackliner andPan/TiltModule
Pushtheblackliner intothetwo locking tabs.Align
thepan/tilt moduletothetwo clips, redtored, black
to black andmatchtheholesin pan/tiltmoduleand
thetwo guide poles.Gently pushthe moduleup-
warduntilyouheartwoclicksound.
NOTE: BesuretheAMPsockets arecleanwithout
dust.DO NOT forgetto removethelens cover.
9Installdowncover
Loosenthetwo M4screws on down coverring.
Applylubricant totheO-ring tomakedown cover
easiertoslipin. Push upwardthedowncoverinto
thehousing and thenfastendown coverwithtwo
M4 screws.
M4
Lube
AMPSocket Red Lable
Red Clip
Connect thetwo
portsof theheater
SafetyChain
M3 Nut

-17-
2Install base
Put Power/RS485/Video cablesthroughthecentral
holeof thebracketbase,andthenfix itonceiling.
NOTE: Applysiliconealong thetop of bracket
baseinthecaseofoutdoordome.
Silicone
1Mark screwspositions
Takethebracket baseasthetemplatetomark the
screws positions onceiling.Drilltheholesandput
expansionscrews inside.
Installationrequirements:
Theceiling must befirmenough tobear4 timesthe
weightofthespeeddome.
Pendent Mount

-18-
6Connect cables
Insertcablesinto correspondingsocketson power
board.Aftercompleting cableconnection, swing the
power board holderback and thenturnon thepower.
TheredLED will light up.Turn offthepower after
checking. If not lightup, checkthecableconnection.
NOTE: Therearesigns foreachport.Pleasecon-
nectcablesaspicture showedinpage3.Please
MAKE SURE power is off beforedoing connection.
3Installsuspender
Put cables throughthecavityofsuspender. Apply
water-prooftapeto thethread. Thenturnthe
threadpipeheadintothebracketbaseandfasten
theconnectionwithanM4screw.
NOTE: Applysiliconeto thesuspenderas picture
showsinthecaseof outdoordome.
Silicone
M4
Tape
Thread
4Unfasten thepower boardholder
Loosenthebolt and swing awaythepowerboard
holder.
5Installhousing
Insert cables through theholeat thetop of thehous-
ingApply water-proof tapetothehousingthread.
Thenturnthehousing ontothewallmount bracket
andretaintheconnectionwithanM4screw. Ifin-
stallation heightis nothighenough, mount housing
directlyinto thebase.
NOTE: Apply siliconeto thegapbetweenbracket
andwall inthecaseofoutdoor dome.
Tape
M4
Tape
M4
Bolt
Alarm
Power
Video&RS485