TeleEye NX288 User manual

1
Quick Start Guide
TeleEye NX288 Network Camera
This Quick Start Guide will take you through the process to install and configure TeleEye NX288 network camera for
remote monitoring, recording and playback on a PC.
Camera Calibration
Step 1: fter mounting the camera on the wall or ceil, connect the analog video output to a monitor by using the
analog video cable.
Step 2: djust the direction (pan/tilt/rotation) of the camera (the le t diagram below), the focal and the focus by
sliding the sticks at the side of the lens (the right diagram below).
Step 3: djust the IRIS level of uto Iris lens by tuning the “DC LEVEL” as shown in the following diagram.
Analog Video Cable
Connect to
NX288 with cover removed
djust focus
djust focal
Rotation
Tilt
Pan
Adjust the direction (pan/tilt/rotation) Adjust the ocal and the ocus

2
FL: Flickerless
FL: In FL mode, the shutter speed is 1/100sec. (NTSC
system) / 1/120sec. (P L).
If choose FL mode, [ ES] switch should be off.
NOM: Normal position
AGC:
Automatic Gain Control
ON: GC level of gain varies from 0 to 26dB.
OFF: GC OFF. The level of gain is fixed at 0dB.
BLC: Backlight Compensation
When the object is dark by strong light, please turn on BLC to
make object become bright.
AES: Automatic Electronic Shutter
ON: The range of shutter speed from 1/60 (1/50sec.) to
1/100,000 sec. This mode is employed for using a
manual iris lens.
OFF: The shutter speed is 1/60sec. (1/50sec.).
When an auto iris lens is applied, ES should be off.
Step 4: Finally, disconnect the analog video cable and close the camera cover.sd
Camera Installation with PoE
Step 1: Connect NX288 to network switch / router with 802.3af PoE supported.
Step 2: Wait for around 1 minutes for the NX288 to startup.
TeleEye NX288
Network switch / router
with PoE supported
210.17.139.53
Straight-through
Ethernet Cable
LAN Adapter
Internet
Camera Installation without PoE
Step 1: Connect NX288 to power adapter.
Step 2: Connect NX288 to network switch / router.

3
Step 3: Wait for around 1 minutes for the NX288 to startup.
TeleEye NX288
Network switch / router
210.17.139.53
Straight-
t
hrough
Ethernet Cable
LAN Adapter
Internet
Camera’s
DC Adapter
IP Setup Utitlity
Step 1: Install IP Setup Utility software to a PC.
Step 2: Run IP Setup Utility software.
Step 3: From the IP setup utility, match your own NX288 by its unique serial number. You can change its IP/port, etc.
on the right side of the window. Press [Apply] button when you finished.
Live Monitoring with Web-Browser
Step 1: On the PC side, open a web browser and type in the IP address of the NX288. (NX288’s IP address of this
example is 210.17.139.53, type in http://210.17.139.53 in a web browser).
Step 2: Type in the Password. (The default password is 000000).
Step 3: Wait for connecting the NX288.

4
Step 4: monitoring screen will be shown on the browser.
WX-M4Lite Reception So tware
Users can install WX-M4Lite reception software
from the software CD. WX-M4Lite is a back-end
application which works in conjunction with NX
network camera to build up a complete IP and
mobile surveillance system. WX-M4Lite allows:
 Up to 4 cameras monitoring
 Triplex operations
 Digital video recording, playback and
electronic patrol
 Sophisticated event management
 Full screen display
WX-M4Lite is a lite version of WX-M16 which provides more comprehensive functions than WX-M4Lite. For details of the
above information, please refer to the manual of WX-M4Lite reception software.
END
Step 2’s screenshot: Type in the Password Step 4’s screenshot: Web-monitoring screen