TeleEye MX600 User manual

MX Series
HD Network Camera
MX600 SpeedDome Series
Installation Guide

Notice:
Signal Communications Limited reserves the right to make improvements to the product
described in this manual at any time and without notice.
This manual is copyrighted. All rights are reserved. This manual should not be copied,
reproduced or translated in whole or part without prior consent from Signal
Communications Limited.
TeleEye is a trademark of Signal Communications Limited and is registered in China,
European Communities, ong Kong, US and other countries.
All other trademarks are the property of their respective owners.
Copyright (c) 2012 Signal Communications Limited (A member of TeleEye Group).
All rights reserved.
Version 0.2
Limits of Lia ility and Disclaimer of Warranty
Signal Communications Limited has taken care in preparation of this manual, but makes
no expressed or implied warranty of any kind and assumes no responsibility for errors or
omissions. No liability is assumed for incidental or consequential damages in connection
with or arising out of the use of the information or accessories contained herein.
Features and specifications are subject to change without prior notice.

Contents
1. Introduction........................................................................................................................7
2. Safety Cautions..................................................................................................................8
3. Hardware Installation.........................................................................................................9
3.1 MX677-H ......................................................................................................9
Features.......................................................................................................9
Package Content........................................................................................11
iagram......................................................................................................12
Installation..................................................................................................13
4. Software Installation.........................................................................................................15
4.1 PC Requirements..........................................................................................15
4.2 sureSIGHT Installation..................................................................................16
5. Network Configuration.....................................................................................................20
5.1 Connecting the Camera to Network.............................................................20
5.2 Changing the IP Address..............................................................................20
6. Video Monitoring..............................................................................................................23
6.1 sureSIGHT....................................................................................................23
6.2 Web Browser................................................................................................27
7. Appendix..........................................................................................................................30
7.1 Functional Features......................................................................................30
H SMAC-M – Revolutionary Multi-stream Coder for H Video...............30
16:9 Aspect Ratio Providing Wider View ..................................................30
Superb Video Quality with Great etails ...................................................30

High efinition Progressive Scan Video....................................................31
IP-based Video Surveillance Solution........................................................31
Total Solution for H Video Surveillance...................................................31
Video Surveillance Everywhere.................................................................31
7.2 Specifications................................................................................................32
MX600 Series.............................................................................................32
7.3 imensions...................................................................................................34
MX677-H ..................................................................................................34

MX600 User Guide
1. Introduction
TeleEye MX Series is a complete portfolio of professional and practical D
network camera utilizing our proprietary D SMAC-M compression technology.
The MX series offers the balanced combination of high-quality video, mobility,
scalability and cost effectiveness. By using TeleEye MX, users can build an
integrated, scalable, wired or wireless IP & mobile video surveillance solution
over existing network infrastructure. With the support of TeleEye versatile back-
end applications, users can gain extra control over their TeleEye business
management beyond security.
PAGE 7

MX600 User Guide
2. Safety Cautions
•Do not install the camera in extreme temperature conditions. Use the camera under
conditions where temperatures are within -30C ~ +40C: (-22F ~ 104F)
•Do not install the camera under unstable lighting conditions. Severe lighting change
or flicker can cause the camera to work improperly.
•Do not install or use the camera in an environment where humidity is high. This can
result in poor-quality image.
•Do not disassemble the camera. There are no user serviceable parts inside it.
Opening or removing the camera’s cover may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified personnel only.
•Do not touch the imaging surface of sensor. Use a soft cloth with alcohol to clean
the surface if it is touched accidentally.
•The camera may be damaged by electrical and physical shock. Use regulated 24V
DC, 3A power supply. Do not throw or drop it onto the floor.
•The camera can be used outdoor. But if it is used outdoor, it is required to avoid
direct light from the sun. Do not use it under water.
PAGE 8

MX600 User Guide
3. Hardware Installation
3.1 MX677-HD
MX677-HD High-definition SpeedDome
Features
•1/3” 2MP Sony CMOS Sensor
•720p @ 25fps
•Zoom: Optical 20X + Digital 12X
•Day / Night, Minimum illumination: 0.095lux
•Presets, Patrol, Tour and Auto-scan
•Privacy Masking up to 8 independent masks
•IP66 Weather Resistance
•D SMAC-M multi-stream coder for D video
•Independent D video recording stream
•Independent mobile stream for mobile phone viewing
•Optional sureREC D Video Recording Solution
PAGE 9

MX600 User Guide
•Optional sureSIG T Integrated Video Management Solution
PAGE 10

MX600 User Guide
Package Con tent
Content Description Content Description
MX677- D
Wall Mount Bracket
MX677- D
ousing
MX677- D
PTZ Core
24V AC
Power Supply
Network Cable Screws
Registration Code
Sheet Warranty Card
Installation Guide Software CD
PAGE 11

MX600 User Guide
Diagram
PAGE 12

MX600 User Guide
Ins tallation
1. Draw the framework for bracket installation. Drill 4 holes on the wall.
2. Set 4 pieces of screws through the bracket and mount the bracket onto the wall.
3. Open the Lower Cover and remove the PTZ Core.
4. Then open the interface aluminum board inside the Upper ousing as follow:
PAGE 13

MX600 User Guide
5. Connect the wires and lock the Upper ousing to the Wall Mount Bracket as below:
6. Then, set the PTZ Core into the Upper ousing and close the Lower Cover.
7. Finally, add the Twisted Pair Surge Protection Device between the SpeedDome and
the Network for surge protection in outdoor environment.
PAGE 14

MX600 User Guide
4. Software Installation
In this chapter, it will guide you how to install the sureSIG T software.
4.1 PC Requirements
sureSIGHT Lite sureSIGHT Business sureSIGHT Pro
Processor Intel® Core™ 2 Duo
Processor Intel® Core™ 2 Quad Processor
Memory 2GB or above
Hard Drive 2GB of free space or above
Optical Drive CD-ROM or DVD-ROM
Display 1280x800 resolution or above
Direct3D supported
Sound Sound Card is required
Ethernet 10/100Mbps or above
Port Serial Port
Operating
System
Microsoft Windows XP SP3, VISTA SP1 or 7
(32-bit or 64-bit Edition)
PAGE 15

MX600 User Guide
4.2 sureSIGHT Installati n
sureSIG T is an integrated video management platform for IP cameras and Video
Recording Servers. Its modular design allows customers to scale up easily and add
functional modules to suit specific requirements.
For the sureSIG T installation, please refer to the following steps:
Step 1. Put the installation CD into the CD-ROM or DVD-ROM, the installer should
run automatically. If not, open the CD manually and execute the
“Installer.exe”
Step 2. Click the [Install] button next to “sureSIGHT” in the installation menu.
Step 3. Click the [Next >] button in the welcome window.
PAGE 16

MX600 User Guide
Step 4. After reading the License Agreement, select “I gree” to confirm and then
click the [Next >] button.
Step 5. [Browse] to change the installation path of sureSIG T.
[Disk Cost...] to check the available space for the installation.
[Note] The default path “C:\Program Files\TeleEye\TeleEye sureSIGHT\” is recommended
PAGE 17

MX600 User Guide
Step 6. Click the [Next >] button twice to confirm and start the installation.
Step 7. When the installation is completed successfully, click the [Close] button to
close the window.
PAGE 18

MX600 User Guide
Step 8. If the PC does not have JAVA runtime installed, click the [Install] button next
to “J V Runtime” from the installation menu to install.
Step 9. After completing all the necessary installations, sureSIG T is now ready in
the start menu.
PAGE 19

MX600 User Guide
5. Network Configuration
In this chapter, it will guide you how to setup the target camera IP address.
5.1 C nnecting the Camera t Netw rk
Before setting the IP address, please make sure the network connection is correct as
following diagram:
5.2 Changing the IP Address
Step 1. Turn on the network camera and make sure the camera is connected to the
network. Then select the “Run TeleEye IP Setup Utility” from the start menu.
Step 2. Search the target camera by its serial number, and hightlight the
corresponding row from the list on the left side of the window to select it. If
the camera cannot be found, click the [Refresh] button.
PAGE 20