Televes MIMO evoca TV-130990 Installation instructions

TOTV TOANT
USB
MIMO Antenna
TV-130990
1
WITH A SUPPORT
Attach the plate Ein the right position as
shown in the pictures. Screw it to the antenna
Ausing both screws D.
Place the antenna in a vertical position and attach
it to the mast using the clamp Band the nuts
C.
B
NEEDED TOOLS
10mm wrench
Screw driver
(not included)
PH #2
Installation
C
Contents of the box
Assembly, operation, and maintenance instructions
A
D
E
Mast mount
A
E
EB
C
PH #2
D
By
FG H

2
WITH A REFLECTOR
Remove the clamp and the screws from the plate
Eusing a 10mm wrench.
Put the plate in the right position as shown by
the arrow. Screw it to the antenna using both
screws E.
Rest the antenna on the table in a vertical position
as shown in the picture below.
TABLE MOUNT
D
E
WITHOUT A REFLECTOR
Place the antenna on the table in a vertical
position as shown in the picture.
A
A
PH #2
3
Remove the clamp and the screws from the plate
Eusing a 10mm wrench (not included).
Place the reector as shown in the pictures and
screw the reector using both screws D.
Finally, attach it to the wall with two screws (not
included).
WALL MOUNT
A
E
PH #2
D
H
H

LIGHTNING PROTECTION
If installed outdoors, be sure the antenna
system is grounded so as to provide
protection against voltage surges and built-
up static charges. Section 810 of the National
Electrical Code ANSI/NFPA70, or CSA C22.1
sections 10, 16, and 54, of the Canadian
Electrical Code, provide information with
respect to proper grounding of the mast
and supporting structure, grounding of the
antenna lead-in wire to an antenna discharge
unit, size of grounding conductors, location
of antenna-discharge unit, connection to
grounding electrodes, and requirements
for the grounding electrode (see gure and
instructions).
Mount the lightning arrestor or 75 ohm
coaxial grounding block as close as possible
to where the 75 ohm coaxial cable down
lead enters the house.
The ground wires for both the mast and the
down lead should be copper or aluminium
wire, number eight (8) or larger.
The down lead wire from the antenna to
the lightning arrestor and the mast ground
wire should be secured to the house, spaced
from four (4) to six (6) feet apart.
In the case of a “ground up” antenna
installation it may not be necessary to
ground the mast if the mast extends four
or more feet in the earth. Consult a TV
serviceman for the proper depth in your
location.
WARNINGS
To prevent re or shock hazard, do not
expose the included power supply to rain or
moisture.
Installation of o-air antennas near power
lines is dangerous. For your safety, follow
the installation instructions.
Any alteration or modication to the
product or usage not in accordance with
product instructions voids the warranty.
Technical specifications
Ref. 130990
Outputs 5G VERTICAL HORIZONTAL
FRECUENCY MHz 630 - 960 / 1,7 - 2,7
UHF
(CH14 - CH36)
High VHF / UHF
(CH7 - CH13) / (CH14 - CH36)
470 - 608 174 - 216 / 470 - 608
GAIN dBi 0 32 (1) 23 (1) / 32 (1)
Crosspolar rejection dB > 13
Powering V 5
Consumption mA 150
Weight lb 5.74
Dimensions in 13.98 x 13.98 x 4 (without clamp)
Temperature ºC -5... 45
IP IP 53
Safety Instructions
4CONNECTION
1. 5G OUT
2. VERTICAL OUT + V
3. HORIZONTAL OUT + V
(1) Self regulating gain.
Antenna Lead
in Wire
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
NEC - National Electrical Code
Ground
clamp
Electric Service
Equipment
Ground clamps
Power service Grounding Electrode System
(NEC Art 250, Part H)
Antenna Discharge Unit
(NEC Section 810-20)
(May substitute a 75 ohm
Coax Grounding Block)
Grounding Conductors
(NEC Section 810-21)

2022 © Copyright, Televés S.A.U.
TOTV TOANT
USB
PSU
OUTDOOR EXAMPLE 01
H
V
5G
STB
5G MODEM
MIMO MODE
TOTV TOANT
USB
PSU
OUTDOOR EXAMPLE 02
H
V
5G
STB
5G MODEM
NO MIMO MODE
75 Ω
TOTV TOANT
USB
PSU
INDOOR EXAMPLE
H
V
5G
STB
5G MODEM
MIMO MODE
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
tion against harmful interference when the equipment is ope-
rated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not insta-
lled and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
YELLOW
GREENVIOLET
BLUE LIGHT
GREEN
RED
UHF
YELLOW
GREEN
LIGHT
GREEN
High VHF
YELLOW
GREENVIOLET
BLUE LIGHT
GREEN
RED
UHF
YELLOW
GREEN
LIGHT
GREEN
High VHF
UHF High-VHF
+5V
+5V
+5V
NACE 800-688-9282 | [email protected] | nace.tv