Teltonika FMB641 User manual

https://wiki.teltonika-gps.com/view/FMB641_First_Start
FMB641 First Start
Main Page > Professional Trackers > FMB641 > FMB641 First Start
Leading GSM/GNSS Terminal for advanced applications
Contents
1 How to insert SIM card and connect the battery
2 How to insert microSD card into FMB641
3 2x10 socket pinout
3.1 PC Connection (Windows)
3.2 How to install USB drivers (Windows)
3.3 Configuration (Windows)
3.4 Quick SMS configuration
4 Mounting recommendations
5 Safety information
5.1 Precautions
How to insert SIM card and connect the battery
Unscrew 4 screws counterclockwise that are located on the bottom of the device.1.
Remove the cover.2.
Insert SIM card as shown with PIN request disabled or read Security info how to enter it3.
later in Teltonika Configurator. Make sure that SIM card cut-off corner is pointing outside.
SIM slot 1 is closer to PCB, SIM slot 2 is the upper one.
Connect battery as shown to device.4.
After configuration, see “PC Connection (Windows)”, attach device cover back.5.
Screw in all screws. Device is ready to be mounted.6.
SIM card insertion/removal must be performed when device is powered off – external
voltage and internal battery disconnected. Otherwise SIM card might be damaged or device
will not detect it.

FMX6 devices use Standard size SIM cards for SIM1 and SIM2. Currently most of the SIM
cards provided by operators can be disassembled into 3 parts - Standard/Micro/Nano.
Depending on the SIM card construction - during device usage in harsh conditions, SIM
assembly might come apart which causes instability when connecting to operator.
To avoid such risk:
1) If possible - ask operator for Standard SIM card with solid construction (not pre-cut to 3
parts)
2) Do not use SIM cards that were previously disassembled (SIM was taken apart
previously)
3) If you plan to use only one SIM card - insert it into SIM1 slot (lower slot) - this ensures
greater pressure on SIM contacts as the contact bed is pushed by PCB.
When 2 SIM cards are used simultaneously risk is mitigated as well - when SIM1 is
inserted, a greater pressure is applied for SIM2, so SIM parts are harder to come lose
How to insert microSD card into FMB641
Push microSD card lock case.1.
Open microSD card locker.2.
Correctly insert microSD card into slot.3.
Close microSD card locker.4.
Push microSD card lock case to locked position.5.
2x10 socket pinout

PIN
NUMBER PIN NAME DESCRIPTION
1GND (-) Ground
2 CAN1L SAE J1939 CAN interface Low channel 1
3 1 WIRE
POWER
Power supply pin for Dallas 1-Wire®
devices
4 DIN 4 Digital input, channel 4
5 DIN 2 Digital input, channel 2
6 CAN2L SAE J1939 CAN interface Low channel 2
7 AIN2 Analog input, channel 2. Input range:
0-30V/0-10V DC
8 DOUT3 Digital output. Open collector output
9 DOUT2 Digital output. Open collector output
10 AIN3 Analog input, channel 3. Input range:
0-30V/0-10V DC
11 VCC (+) Power supply (+8-32 V DC)
12 CAN1H SAE J1939 CAN interface High channel 1
13 1 WIRE
DATA
Data channel for Dallas 1-Wire® devices
14 DIN 3 Digital input, channel 3
15 DIN 1 Digital input, channel 1. DEDICATED
FOR IGNITION INPUT
16 CAN2H SAE J1939 CAN interface High channel 2
17 AIN1 Analog input, channel 1. Input range:
0-30V/0-10V DC
18 DOUT4/AIN4 Digital output. Open collector output OR
Analog input, channel 4. Input range:
0-30V/0-10V DC
19 DOUT1 Digital output. Open collector output
20 K-LINE K-LINE interface for online Tachograph
Vehicle Data transfer
PC Connection (Windows)
Power-up FMB641 with DC voltage 8-32 V power supply using supplied power cable. LED’s1.
should start blinking, see “FMB641 LED status”.
Connect device to computer using Mini-USB cable connection and install USB drivers, see2.
"How to install USB drivers (Windows)"
You are now ready to use the device on your computer.3.
How to install USB drivers (Windows)
Please download COM port drivers from Teltonika here.1.
Extract and run TeltonikaCOMDriver.exe.2.
Click Next in driver installation window.3.

In the following window click Install button.4.
Setup will continue installing the driver and eventually the confirmation window will appear.5.
Click Finish to complete the setup.
Note: on Windows 7 systems, an additional driver for FMB641 support must be installed. Driver can
be found here.
Configuration (Windows)
At first FMB641 device will have default factory settings set. These settings should be changed
according to the user's needs.
Main configuration can be performed via Teltonika Configurator software. Get the latest FMB641
Configurator version from here. Configurator operates on Microsoft Windows OS and uses
prerequisite MS .NET Framework. Make sure you have the correct version installed.
MS .NET requirements
Operatin
g system
MS .NET
Framework version Version Link
•
Windows
Vista
•
Windows
7
•
Windows
8.1
•
Windows
10
MS .NET Framework
4.6.2
32 and
64 bit
.NET
Fram
ewor
k
Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe.
After launch software language can be changed by clicking in the right bottom corner:
Configuration process begins by pressing on connected device:
After connection to Configurator Status window will be displayed:

Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc.
FMB641 has one user editable profile, which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to device using Save to device button.
Main buttons offer following functionality:
Load from device – loads configuration from device.1.
Save to device – saves configuration to device.2.
Load from file – loads configuration from file.3.
Save to file – saves configuration to file.4.
Update firmware – updates firmware on device.5.
Read records – read records from device.6.
Reboot device – restarts device.7.
Reset configuration – sets device configuration to default.8.
Most important configurator section is GPRS – where all your server and GPRS settings can be
configured and Data Acquisition – where data acquiring parameters can be configured. More
details about FMB641 configuration using Configurator can be found here.
Quick SMS configuration
Default configuration has optimal parameters present to ensure best performance of track quality
and data usage.
Quickly set up your device by sending this SMS command to it:
" setparam
2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0"
GPRS settings:
2001 – APN
2002 – APN username (if there are no APN username, empty field should be left)
2003 – APN password (if there are no APN password, empty field should be left)
Server settings:
2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)
Note: Before SMS text, two space symbols should be inserted.
Default configuration settings
Movement and ignition detection:
Vehicle movement will be detected
by accelerometer
Ignition will be detected by
vehicle power voltage
between 13,2 – 30 V
Device makes a record On Moving if one of these events happen:

300 seconds passes Vehicle turns 10° degrees
Vehicle drives 100 meters
Speed difference between
last coordinate and current
position is greater than 10
km/h
Device makes a record On Stop if:
1 hour passes while vehicle is
stationary and ignition is off
Records sending to server:
If device has made a record it is
sent to the server every 120
seconds
After successful SMS configuration, FMB641 device will synchronize time and update records to
configured server. Time intervals and default I/O elements can be changed by using Teltonika
Configurator or SMS parameters.
Mounting recommendations
Connecting wires
Wires should be connected while the module is not plugged in.
Wires should be fastened to stable wires or other non-moving parts. Any heat emitting
and/or moving objects should be kept away from the wires.
There should be no exposed wires. If factory isolation was removed while connecting
wires, the isolation material should be applied.
If the wires are placed in the exterior or in places where they can be damaged or
exposed to heat, humidity, dirt, etc., additional isolation should be applied and the wires
should not be loose.
Wires cannot be connected to the board computers or control units.
Connecting power source
Be sure that after the car computer goes to sleep mode, power might be still available on
the power wires. Depending on car, this may happen in 5 to 30 minutes period.
When module is connected, measure voltage again to make sure it did not decrease.
It is recommended to connect to the main power cable in the fuse box.
3 A, 125 V external fuse shall be used.
Connecting ignition wire
Be sure to check if it is a real ignition wire i. e. power does not disappear after starting
the engine.
Check if this is not an ACC wire (when key is in the first position, most of the vehicle
electronics are available).
Check if power is still available when you turn off any of vehicles devices.

Ignition is connected to the ignition relay output. As alternative, any other relay, which
has power output when ignition is on, may be chosen.
Connecting ground wire
Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
For better contact scrub paint from the spot where loop is going to be connected.
PAY ATTENTION! Connecting the power supply must be carried out in a very low
impedance point of on-board vehicle network. These points in the car are the battery
terminals. Therefore, we recommend connecting the power of FMB641 (GND and
POWER wires) directly to the battery terminals. Another valid option is to connect the
wires to the main POWER cable inside the fuse box (if there is none, then to the power
supply where the fuses of vehicle’s computer are), GND wire must be connected in a
special point, designed to connect GND vehicle computer. Connecting the GND at an
arbitrary point to the mass of the car is unacceptable, as static and dynamic potentials
on the line GND will be unpredictable, which can lead to unstable FMB641 operation
and even its failure.
Safety information
This message contains information on how to operate FMB641 safely. By following these
requirements and recommendations, you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating the device!
The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed
voltage range is +10..+30V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package.
Before usage, the device should be placed so that its LED indicators are visible. They show the
status of device operation.
When connecting the the 2x10 connector cables, the appropriate jumpers of the vehicle power
supply should be disconnected.
Before unmounting the device from the vehicle, the 2x10 connector must be disconnected.
The device is designed to be mounted in a zone of limited access, which is inaccessible to the
operator. All related devices must meet the requirements of EN 60950-1 standard.
The device FMB641 is not designed as a navigational device for boats.
Precautions
Do not disassemble the device. If the device is damaged, the power supply cables are
not isolated or the isolation is damaged, DO NOT touch the device before unplugging
the power supply.
All wireless data transferring devices produce interference that may affect other
devices which are placed nearby.

The device must be connected only by qualified personnel.
The device must be firmly fastened in a predefined location.
The programming must be performed using a PC with autonomic power supply.
The device is susceptible to water and humidity.
Installation and/or handling during a lightning storm is prohibited.
https://teltonika-gps.com/product/fmb640