Teltonika FMC130 Installation guide

Quick Manual
v1.5
Advanced LTE terminal with
flexible inputs configuration
FMC130

2
FMC130 | Wiki
Table of Contents
Know your device..................................................................................3
Pinout ........................................................................................................................ 4
Wiring scheme ....................................................................................................... 5
Set up your device.................................................................................6
How to insert Micro-SIM card and connect the battery......................... 6
PC Connection (Windows) ................................................................................. 7
How to install USB drivers (Windows) ........................................................... 7
Configuration (Windows) ................................................................................... 7
Quick SMS configuration.................................................................................... 8
Mounting recommendations.............................................................10
LED indications ....................................................................................11
Characteristics .....................................................................................11
Basic characteristics............................................................................................11
Electrical characteristics ....................................................................................12
Safety information..............................................................................14
Certification and Approvals ...............................................................15
Warranty..............................................................................................16
Warranty Disclaimer...........................................................................................16

3
FMC130 | Wiki
Know your device
Figure 1 FMC130 device view

4
FMC130 | Wiki
Pinout
Table 1 FMC130 2x6 socket pinout
PIN NUMBER
PIN NAME
DESCRIPTION
1
VCC (10-30) V DC (+)
Power supply (10-30 V DC).
2
DOUT 3
Digital output, channel 3. Open collector
output. Max. 0,5 A DC.
3
DIN 3 / AIN 2
Analog input, channel 2. Input range: 0-
30 V DC / Digital input, channel 3.
4
DIN 2-N / AIN 1
Digital input, channel 2, Negative input
(ground sense), Analog input, channel 1,
Input range: 0-30 VDC.
5
DIN 1
Digital input, channel 1.
6
INPUT 6
TX EXT (LVCAN –TX).
7
GND (-)
Ground pin. (10-30) V DC (―)
8
DOUT 1
Digital output, channel 1. Open collector
output. Max. 0,5 A DC.
9
DOUT 2
Digital output, channel 2. Open collector
output. Max. 0,5 A DC.
10
1WIRE POWER
+3,8 V output for 1–Wire devices.
11
1WIRE DATA
Data for 1–Wire devices.
12
INPUT 5
RX EXT (LVCAN - RX).
Figure 2 FMC130 2x6 socket pinout

5
FMC130 | Wiki
Figure 3 FMC130 Wiring scheme
Wiring scheme
1
Automotive relay
^1

6
FMC130 | Wiki
Set up your device
How to insert Micro-SIM card and
connect the battery
1. Gently remove FMC130 bottom cover using plastic pry tool from
both sides. Then remove the top cover.
2. Insert Micro-SIM card as shown with PIN request disabled or
read our Wiki how to enter it later in Teltonika Configurator.
Make sure that Micro-SIM card cut-off corner is pointing forward
to slot.
3. Connect battery as shown to device. Position the battery in place
where it does not obstruct other components.
4. After configuration, see “PC Connection (Windows)”, attach device
top and bottom cover back.
Figure 4 Covers removal
Figure 5 Micro-SIM card insert
Figure 6 Battery connection
Figure 7 Cover removal

7
FMC130 | Wiki
PC Connection (Windows)
1. Power-up FMC130 with DC voltage (10 –30 V) power supply
using supplied power cable. LED’s should start blinking, see “LED
indications”.
2. Connect device to computer using Micro-USB cable or Bluetooth
connection:
•Using Micro-USB cable
▬You will need to install USB drivers, see “How to install USB
drivers (Windows)”
•Using Bluetooth
▬FMC130 Bluetooth is enabled by default. Turn on Bluetooth
on your PC, then select Add Bluetooth or other device >
Bluetooth. Choose your device named –
“FMCxxx_last_7_imei_digits”, without LE in the end. Enter
default password 5555, press Connect and then select
Done.
3. You are now ready to use the device on your computer.
How to install USB drivers
(Windows)
1. Please download COM port drivers from here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
Setup will continue installing the driver and eventually the
confirmation window will appear. Click Finish to complete the setup.
Configuration (Windows)
At first FMC130 device will have default factory settings set. These
settings should be changed according to the user's needs. Main
configuration can be performed via Teltonika Configurator software.
Get the latest Configurator version from here.Configurator operates
on Microsoft Windows OS and uses prerequisite MS .NET
Framework. Make sure you have the correct version installed.
Table 2 MS .NET requirements
MS .NET REQUIREMENTS
Operating
system
MS .NET Framework
version
Version
Links
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework
4.6.2
32 and 64 bit
www.microsoft.com
Downloaded Configurator will be in compressed archive. Extract it
and launch Configurator.exe. After launch software language can be
changed by clicking in the right bottom corner (Figure 8
Language selection).

8
FMC130 | Wiki
Configuration process begins by pressing on connected device (Figure
9 Device connected via USB).
After connection to Configurator Status window will be displayed
(Figure 10 Configurator Status window).
Various Status window tabs display information about GNSS,GSM,
I/O, Maintenance and etc. FMC130 has one user editable profile,
which can be loaded and saved to the device. After any modification of
configuration the changes need to be saved to device using Save to
device button. Main buttons offer following functionality:
1. Load from device –loads configuration from device.
2. Save to device –saves configuration to device.
3. Load from file –loads configuration from file.
4. Save to file –saves configuration to file.
5. Update firmware –updates firmware on device.
6. Read records –reads records from the device.
7. Reboot device –restarts device.
8. Reset configuration –sets device configuration to default.
Most important configurator section is GPRS –where all your server
and GPRS settings can be configured and Data Acquisition –where
data acquiring parameters can be configured.
More details about FMC130 configuration using Configurator can be
found in our Wiki.
Quick SMS configuration
Figure 9 Device connected via USB
Figure 8 Language selection
Figure 10 Configurator Status window

9
FMC130 | Wiki
Default configuration has optimal parameters present to ensure best
performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS settings:
•
2001
–APN
•
2002
–APN username (if there
are no APN username, empty
field should be left)
•
2003
–APN password (if there
are no APN password, empty
field should be left)
Server settings:
•
2004
–Domain
•
2005
–Port
•
2006
–Data sending protocol (0
–TCP, 1 –UDP)
Default configuration settings
Movement and ignition detection:
Vehicle movement will
be detected by
accelerometer
Ignition will be detected
by vehicle power voltage
between 13,2 –30 V
Device makes a record On Moving if one of these events happen:
300 seconds passes
Vehicle turns 10 degrees
Vehicle drives 100
meters
Speed difference between
last coordinate and
current position is greater
than 10 km/h
Device makes a record On Stop if:
1 hour passes while
vehicle is stationary and
ignition is off
Records sending to server:
If device has made a
record it is sent to the
server every 120
seconds
After successful SMS configuration, FMC130 device will synchronize
time and update records to configured server. Time intervals and
default I/O elements can be changed by using Teltonika
Configurator or SMS parameters.
" setparam
2001
:APN;
2002
:APN_username;
2003
:APN_password;
2004
:Domain;
2005
:Port;
2006
:0"

10
FMC130 | Wiki
Mounting recommendations
•Connecting wires
▬Wires should be connected while the module is not plugged in.
▬Wires should be fastened to stable wires or other non-moving
parts. Any heat emitting and/or moving objects should be kept
away from the wires.
▬There should be no exposed wires. If factory isolation was
removed while connecting the wires, the isolation material
should be applied.
▬If the wires are placed in the exterior or in places where they
can be damaged or exposed to heat, humidity, dirt, etc.,
additional isolation should be applied and the wires should not
be loose.
▬Wires cannot be connected to the board computers or control
units.
•Connecting power source
▬Be sure that after the car computer goes to sleep mode, power
might be still available on the power wires. Depending on the
car model, this may happen in 5 to 30 minutes period.
▬When the module is connected, measure the voltage again to
make sure it did not decrease.
▬It is recommended to connect to the main power cable in the
fuse box.
▬3 A, 125 V external fuse shall be used.
•Connecting ignition wire
▬Be sure to check if it is a real ignition wire i. e. power does not
disappear after starting the engine.
▬Check if this is not an ACC wire (when key is in the first position,
most of the vehicle electronics are available).
▬Check if power is still available when you turn off any of vehicles
devices.
▬Ignition is connected to the ignition relay output. As alternative,
any other relay, which has power output when ignition is on,
may be chosen.
•Connecting ground wire
▬Ground wire is connected to the vehicle frame or metal parts
that are fixed to the frame.
▬If the wire is fixed with the bolt, the loop must be connected to
the end of the wire.
▬For better contact scrub paint from the spot where loop is
going to be connected.

11
FMC130 | Wiki
LED indications
Table 3 Navigation LED indications
BEHAVIOUR
MEANING
Permanently switched on
GNSS signal is not received
Blinking every second
Normal mode, GNSS is working
Off
GNSS is turned off because:
Device is not working or Device is in
sleep mode
Blinking fast constantly
Device firmware is being flashed
Table 4 Status LED indications
BEHAVIOUR
MEANING
Blinking every second
Normal mode
Blinking every two seconds
Sleep mode
Blinking fast for a short time
Modem activity
Off
Device is not working or Device is in
boot mode
Characteristics
Basic characteristics
Table 5 Basic characteristics
MODULE
Name
Quectel EC21-AU, Quectel EC21-EC, Teltonika
TM2500
Technology
LTE(CaT1)/3G(UMTS/HSPA)/2G(GSM/GPRS)/GNSS/
BLUETOOTH
GNSS
GNSS
GPS, GLONASS, GALILEO, BEIDOU, QZSS, AGPS
Receiver
Tracking: 33
Tracking sensitivity
-165 dBM
Accuracy
< 3 m
Hot start
< 1 s
Warm start
< 25 s
Cold start
< 35 s
CELLULAR
Technology
LTE Cat 1, UMTS, GSM
2G bands
EC21-AU: GSM: B2/B3/B5/B8
EC21-EC: GSM: B3/B8
3G bands
EC21-AU: WCDMA: B1/B2/B5/B8
EC21-EC: WCDMA: B1/B8
4G bands
EC21-AU: LTE FDD: B1/B2/B3/B4/B5/B7/B8/B28
LTE TDD: B40
EC21-EC: LTE FDD: B1/B3/B7/B8/B20/B28A
Data transfer
LTE: LTE FDD: Max 10Mbps (DL)/Max 5Mbps (UL)
LTE TDD: Max 8.96Mbps (DL)/Max 3.1Mbps (UL)
UMTS: WCDMA: Max 384Kbps(DL)/Max 384Kbps(UL)
GSM: GPRS: Max 107Kbps (DL)/Max 85.6Kbps (UL)
Data support
SMS (text/data)
POWER
Input voltage range
10-30 V DC with overvoltage protection
Back-up battery
170 mAh Li-Ion battery 3.7 V (0.63 Wh)
Power consumption
At 12V < 2.5 mA (Ultra Deep Sleep)
At 12V < 5 mA (Deep Sleep)
At 12V < 5.5 mA (Online Deep Sleep)

12
FMC130 | Wiki
At 12V < 18,5 mA (GPS Sleep)
At 12V < 34 mA (nominal)
BLUETOOTH
Specification
4.0 + LE
Supported peripherals
Temperature and Humidity sensor, OBDII dongle,
Inateck Barcode Scanner, Universal BLE sensors
support
PHYSICAL SPECIFICATION
Dimensions
65 x 56 x 20,6 mm (L x W x H)
Weight
55 g
INTERFACE
Digital Inputs
3
Negative Inputs
1 (Digital Input 2)
Impulse Inputs
2 (Digital Input 1, Digital Input 2)
Digital Outputs
3
Analog Inputs
2
CAN Adapter inputs
1
1-Wire
1
GNSS antenna
Internal High Gain
Cellular antenna
Internal LTE High Gain
USB
2.0 Micro-USB
LED indication
2 status LED lights
SIM
Micro-SIM + eSIM
Memory
128MB internal flash memory
OPERATING ENVIRONMENT
Operating temperature
(without battery)
-40 °C to +85 °C
Storage temperature (without
battery)
-40 °C to +85 °C
Operating humidity
5% to 95% non-condensing
Ingress Protection Rating
IP41
Battery charge temperature
0 °C to +45 °C
Battery discharge temperature
-20 °C to +60 °C
Battery storage temperature
-20 °C to +45 °C for 1 month
-20 °C to +35 °C for 6 months
FEATURES
Sensors
Accelerometer
Scenarios
Green Driving, Over Speeding detection, GNSS
Fuel Counter, DOUT Control Via Call, Excessive
Idling detection, Immobilizer, iButton Read
Notification, Unplug detection, Towing detection,
Crash detection, Auto Geofence, Manual Geofence,
Trip, Ground Sense
Sleep modes
GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra
Deep Sleep
Configuration and firmware
update
FOTA Web, FOTA, Teltonika Configurator (USB,
Bluetooth), FMBT mobile application
(Configuration)
SMS
Configuration, Events, DOUT control, Debug
GPRS commands
Configuration, DOUT control, Debug
Time Synchronization
GPS, NITZ, NTP
Fuel monitoring
LLS (Analog), LV-CAN200, ALL-CAN300, OBDII
dongle, CAN-CONTROL, OBDII dongle
Ignition detection
Digital Input 1, Accelerometer, External Power
Voltage, Engine RPM (CAN Adapters, OBDII
dongle)
Electrical characteristics
Table 6 Electrical characteristics
CHARACTERISTIC DESCRIPTION
VALUE
MIN.
TYP.
MAX.
UNIT
SUPPLY VOLTAGE
Supply Voltage (Recommended Operating
Conditions)
+10
+30
V

13
FMC130 | Wiki
DIGITAL OUTPUT (OPEN DRAIN GRADE)
Drain current (Digital Output OFF)
120
µA
Drain current (Digital Output ON, Recommended
Operating Conditions)
0.1
0.5
A
Static Drain-Source resistance (Digital Output ON)
400
600
mΩ
DIGITAL INPUT
Input resistance (DIN1)
47
kΩ
Input resistance (DIN2)
38.45
kΩ
Input resistance (DIN3)
150
kΩ
Input voltage (Recommended Operating
Conditions)
0
Supply
voltage
V
Input Voltage threshold (DIN1)
7.5
V
Input Voltage threshold (DIN2)
2.5
V
Input Voltage threshold (DIN3)
2.5
V
ANALOG INPUT
Input voltage (Recommended Operating
Conditions), Range 1
0
+10
V
Input resistance, Range 1
38.45
kΩ
Measurement error on 12V, Range 1
0.9
%
Additional error on 12 V, Range 1
108
mV
Measurement error on 30 V, Range 1
0.33
%
Additional error on 30 V, Range 1
88
mV
Input Voltage (Recommended Operating
Conditions), Range 2
0
+30
V
Input resistance, Range 2
150
kΩ
Measurement error on 12 V, Range 2
0.9
%
Additional error on 12 V, Range 2
108
mV
Measurement error on 30 V, Range 2
0.33
%
Additional error on 30 V, Range 2
88
mV
OUTPUT SUPPLY VOLTAGE 1-WIRE
Supply voltage
+4.5
+4.7
V
Output inner resistance
7
Ω
Output current (Uout > 3.0 V)
30
mA
Short circuit current (Uout = 0)
75
mA
NEGATIVE INPUT
Input resistance
38.45
kΩ
Input voltage (Recommended Operating
Conditions)
0
Supply
voltage
V
Input voltage threshold
0.5
V
Sink current
180
nA

14
FMC130 | Wiki
Safety information
This message contains information on how to operate FMC130 safely. By
following these requirements and recommendations, you will avoid
dangerous situations. You must read these instructions carefully and follow
them strictly before operating the device!
•The device uses SELV limited power source. The nominal voltage is +12 V
DC. The allowed voltage range is +10..+30 V DC.
•To avoid mechanical damage, it is advised to transport the device in an
impact-proof package. Before usage, the device should be placed so that
its LED indicators are visible. They show the status of device operation.
•When connecting the 2x6 connector wires to the vehicle, the appropriate
jumpers of the vehicle power supply should be disconnected.
•Before unmounting the device from the vehicle, the 2x6 connector must
be disconnected. The device is designed to be mounted in a zone of
limited access, which is inaccessible to the operator. All related devices
must meet the requirements of EN 60950-1 standard.
The device FMC130 is not designed as a navigational device for boats.
Do not disassemble the device. If the device is damaged,
the power supply cables are not isolated or the isolation
is damaged, DO NOT touch the device before unplugging
the power supply.
All wireless data transferring devices produce interference
that may affect other devices which are placed nearby.
The device must be connected only by qualified
personnel.
The device must be firmly fastened in a predefined
location.
The programming must be performed using a PC with
autonomic power supply.
Installation and/or handling during a lightning storm is
prohibited.
The device is susceptible to water and humidity.
Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to the
instructions.
Battery should not be disposed of with general household
waste. Bring damaged or worn-out batteries to your local
recycling center or dispose them to battery recycle bin
found in stores.

15
FMC130 | Wiki
Certification and Approvals
•FMC130 EAC
•FMC130 REACH
•FMC130 Declaration of IMEI assignment
•FMC130 CE / RED
•FMC130 E-Mark
•FMC130 RoHS
•FMC130 Declaration of device operation temperature
This sign on the package means that it is
necessary to read the User‘s Manual before
your start using the device. Full User‘s Manual
version can be found in our Wiki.
This sign on the package means that all used
electronic and electric equipment should not be
mixed with general household waste.
Hereby, Teltonika declare under our sole
responsibility that the above described product
is in conformity with the relevant Community
harmonization: European Directive 2014/53/EU
(RED).

16
FMC130 | Wiki
Warranty
TELTONIKA guarantees its products to be free of any manufacturing
defects for a period of 24 months. With additional agreement we can
agree on a different warranty period, for more detailed information
please contact our sales manager.
Contact us teltonika.lt/company/contacts
All batteries carry a reduced 6 month warranty period.
If a product should fail within this specific warranty time, the product
can be:
•Repaired
•Replaced with a new product
•Replaced with an equivalent repaired product fulfilling the same
functionality
•TELTONIKA can also repair products that are out of warranty at an
agreed cost.
Warranty Disclaimer
TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS
WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS
THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED
WARRANTIES NULL AND VOID AND SAME ARE HEREBY
EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY
ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE,
LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC
LOSS.
More information can be found at teltonika.lt/warranty-repair