Texas Instruments LaunchPad CC1312PSIP User manual

™
Meet the
CC1312PSIP
LaunchPad
Development Kit
Connect your LaunchPad to a computer
and visit dev.ti.com
Part Number: LP-EM-CC1312PSIP
BoosterPack Ecosystem
SimpleLink ULP Sense
BoosterPack
- Flow meter measurements
- Ultra low power accelerometer
- Two cap touch buttons
- Analog Light Sensor
- Reed switch
- 0-200kΩpotentiometer
See them all @ ti.com/boosterpacks
>>
Software Tools SmartRF Studio
A powerful application to
evaluate radio performance.
Professional Software tools
LaunchPads are supported by
professional IDEs that
provide industrial-grade
features and full debug-
capability. Set breakpoints,
watch variables, profile code,
inspect memory and more.
Sharp 128x128 Memory
LCD and microSD card
BoosterPack
- 1.28 128 x 128 pixel LCD
(LS013B7DH03)
- microSD card slot
- DCDC 3V to 5V converter
- Ultra-low-power operation
R
2023 Texas Instruments Incorporated. The platform bar, LaunchPad, EnergyTrace and Code Composer Studio
are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
c
The BoosterPack™ connector
The pinout to connect BoosterPack accessories (available separately) are shown below.
www.ti.com/ccs
Code Composer Studio
IDE
TM
XDS110 EnergyTrace™ Technology
The LP-EM-CC1312PSIP is compatible with the EnergyTrace technology.
EnergyTrace implements a new method for measuring MCU current consumption. It uses
a DC-DC solution to measure the time density of charge pulses, allowing accuracy on
ultra low power measurements. Its high dynamic range (700 nA to 400 mA) and fast
sampling rate (256 kSPS) captures the complete operational profile of the wireless MCU.
Find more information at
ti.com/EnergyTrace
EnergyTrace Profile
EnergyTrace Profile runtime and energy data for low power modes along with each
function run during Active Mode.
Graphical Power Data in Code Composer Studio
These two tabs of the EnergyTrace Technology window show a graph over time of
power and energy.
UART (RXD, TXD), Reset (LP_RST) and JTAG (TMS, TCK, TDO and TDI) are also present in the
LP-EM Debug Connector. Power (GND, 3V3 and 5V) is also provided.
SPAZ037
20
19
18
17
16
15
14
13
12
11
GND
40
39
38
37
36
35
34
33
32
31
DIO19
DIO11
LP_RST
DIO9
DIO8
DIO15
DIO14
DIO7
DIO6
DIO20
DIO4
SPI_CS
SPI_MOSI
SPI_MISO
CTS
SWO
BP_RST*
TMS
TCK
TDO
TDI
BTN_2
BTN_1
RLED
GLED
Flash_CS
1
3
4
5
7
8
9
10
3V3
DIO23
21
22
23
24
25
26
27
28
29
30
5V
GND
2
6
DIO22
DIO24
DIO10
SPI_CLK
DIO31
DIO21
I2C_SCL
DIO5
I2C_SDA
DIO25
DIO26
DIO27
DIO28
DIO29
DIO30
DIO1
DIO2
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
RXD
TXD
DIO12
DIO13

A closer look at your new
LaunchPad Development Kit
Featured microcontroller: CC1312PSIP
This LaunchPad is great for...
- Battery-operated wireless applications operating in the Sub-1GHz ISM RF bands (868MHz and 915MHz)
- Add RF capabilities to your product using one of the supported protocols: IEEE 802.15.4g, Wi-SUN®,
Wireless M-Bus, MIOTY®and proprietary protocols
What comes in the box?
LP-EM-CC1312PSIP
LaunchPad
CC1312PSIP Microcontroller
- 48 MHz CPU
- 352kB Flash, 80 kB RAM
- Programmable radio supporting
various protocols and up to +20 dBm
at 868MHz and 915MHz
- Low power consumption
QSG
This Quick
Start Guide
10-pin
Debug Cable
2-wire
Power Cable
CC1312PSIP
{
{
- Four 32-bit or eight x 16-bit timers
- ADC with 8 channel, 12 bits and 200 ksamples/s
- DAC with 8 bits
- Serial communications: UART, SPI, I2C
- Two comparators
Separate LaunchPad
Hardware setup
LP-XDS110 or LP-XDS110ET
USB to the host
computer
USB to the host
computer
10-pin Debug Connector
Allows using an external JTAG Debug
Probe to debug/program the device
CC1312PSIP
Wireless Microcontroller
LP-EM-CC1312PSIP Overview
Remove all jumpers,
except GND and 3V3
Jumper on the position
XDS110 Power
Option 2: Using the 10-pin debug connector
LP-EM Debug Connector
Together with a LP-XDS110 or
LP-XDS110ET, allows:
- Debugging and programming
- Communicate to the host via UART
- Powering the microcontroller
20-pin BoosterPack
plug-in module connector
(J1, J2, J3 & J4)
Button/Switch
BTN-1 (DIO15)
Button/Switch
BTN-2 (DIO14)
User LEDs
Red (DIO6)
Green (DIO7)
{
Antenna
LP-EM-CC1312PSIP
What do you need?
To use your new LaunchPad, you need to connect an external Debug Probe to either the 20-pin
LP-EM Debug connector on the edge of the board or to the 10-pin Debug connector and supply
power separately.
Option 1: Using the LP-EM Debug Connector
This is the easiest way to setup the hardware. It requires either an LP-XDS110 or
2-wire Power Cable
10-pin Debug Cable
LP-EM-CC1312PSIP
For additional details, consult dev.ti.com/LP-EM-CC1312PSIP

IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2024, Texas Instruments Incorporated