Texas Instruments TPS929120EVM User manual

1
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
User's Guide
SLVUBM2B–April 2019–Revised December 2019
TPS929120EVM User's Guide
This user's guide describes the setup and use of the TPS929120EVM evaluation module (EVM). This
EVM helps the user evaluate the features of the Texas Instruments TPS929120-Q1, which is an
automotive 12-channel LED driver with FlexWire interface, to address increasing needs of individual
control of each LED string. This document includes hardware setup instructions, software instructions, a
schematic diagram, a bill of materials and printed-circuit board layout drawings.
Contents
1 What You Get ................................................................................................................ 3
2 What You Need In Addition ................................................................................................ 3
3 How to Get Started .......................................................................................................... 3
4 Board Layout................................................................................................................ 15
List of Figures
1 TPS929120EVM Kit ......................................................................................................... 3
2 Hardware Setup Without CAN Transceiver .............................................................................. 4
3 TPS929120EVM Jumper Configurations without TPS929120CANEVM Connected ............................... 4
4 Hardware Setup with CAN Transceiver................................................................................... 5
5 TPS929120EVM Jumper Configurations With TPS929120CANEVM Connected .................................. 6
6 TPS929120CANEVM Jumper Configurations ........................................................................... 7
7 TPS929120-Q1 Gallery Page.............................................................................................. 7
8 GUI and GUI Composer Download Page ................................................................................ 8
9 GUI Composer Runtime Installation....................................................................................... 8
10 Firmware Update Prompt Window......................................................................................... 9
11 USB2ANY Firmware Loader.............................................................................................. 10
12 TPS929120EVM GUI Connection Status............................................................................... 11
13 Walkthrough Wizard Prompt.............................................................................................. 11
14 TPS929120EVM GUI Quick Start Page................................................................................. 12
15 TPS929120EVM GUI Advanced Page.................................................................................. 13
16 TPS929120EVM GUI EEPROM Programming Page ................................................................. 14
17 TPS929120EVM GUI Registers Page................................................................................... 14
18 Top Layer Routing ......................................................................................................... 15
19 Bottom Layer Routing (Mirrored)......................................................................................... 15
20 TPS929120EVM Schematic Diagram ................................................................................... 17
List of Tables
1 TPS929120EVM Jumpers Setting without TPS929120CANEVM Connected....................................... 5
2 TPS929120EVM Jumpers Setting with TPS929120CANEVM Connected........................................... 6
3 Bill of Materials (BOM)..................................................................................................... 18

www.ti.com
2SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
WARNING
Hot surface! Contact may cause burns. Do not touch!
Some components may reach high temperatures
>55°C when the board is powered on. The user must
not touch the board at any point during operation or
immediately after operating, as high temperatures may
be present.
Trademarks
All trademarks are the property of their respective owners.

www.ti.com What You Get
3
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
1 What You Get
The TPS929120EVM kit (Figure 1) contains:
• USB2ANY
– Ribbon cable
– USB cable
• TPS929120EVM
• TPS929120CANEVM
• DB-09 cable
Figure 1. TPS929120EVM Kit
2 What You Need In Addition
The following additional items are required to run the TPS929120EVM:
• PC with TPS929120EVM GUI installed or to run the on-line TPS929120EVM GUI
• 12-V DC power supply
3 How to Get Started
3.1 Hardware Setup
There are two hardware setups to simulate the communication between MCU and TPS929120-Q1 directly
or through CAN transceiver.
3.1.1 Communication Without CAN Transceiver
Figure 2 shows the hardware setup when TPS929120CANEVM is not used. Figure 3 shows the jumper
configurations for the TPS929120EVM without TPS929120CANEVM connected. This is the default jumper
configuration shipped with the board.

USB2ANY
TPS929120EVM
x
x
x
x
x
VSUPPLY_EXT
USB cable
GND
Ribbon Cable
TP1 TP2
J3
DC
Supply
12V
+
-
How to Get Started www.ti.com
4SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
Figure 2. Hardware Setup Without CAN Transceiver
• Connect a 12-V power supply to TP1 (VSUPPLY_EXT) and TP1 (GND).
• Connect USB2ANY tool to PC through the USB cable.
• Connect USB2ANY tool to the J3 connector of TPS929120EVM through ribbon cable.
Figure 3. TPS929120EVM Jumper Configurations without TPS929120CANEVM Connected

USB2ANY
TPS929120EVM
x
x
x
x
x
VSUPPLY_EXT
USB
cable
TPS929120CANEVM
GND
DB09 cable
TP1 TP2
J3 J4
J7
DC
Supply
12V
+
-
www.ti.com How to Get Started
5
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
Table 1. TPS929120EVM Jumpers Setting without TPS929120CANEVM Connected
HEADER SETTING
J2, J4, J5, J6, J10, J17, J19, J20, J40 Open
J8, J9, J11 Short
J12 Short “FS” to “H”
J13 Short “ADDR2” to “L”
J14 Short “ADDR1” to “L”
J15 Short “ADDR0” to “H”
J16 Short “TX_C” to “RX”, “RX_C” to “TX”, “ERR_C” to “ERR”, “ADDR2/CLK_C” to “ADDR2/CLK”, “ADDR1/CLK_C” to
“ADDR1/CLK”, “ADDR0/CLK_C” to “ADDR0/CLK”
J30 Short “OUTx” to “OUTx_MONO”, where x=0 to 11
All headers paralleled with LEDs Open
3.1.2 Communication with CAN Transceiver
Figure 4 shows the hardware setup when TPS929120CANEVM is used. Figure 5 shows the jumper
configurations for TPS929120EVM with TPS929120CANEVM connected. With this setup, the clock and
PWM signal terminals from the USB2ANY are disconnected to such signal terminals of the TPS929120-
Q1 device on the TPS929120EVM. As a result, an extra instrument for generating the PWM or clock
signal is required to simulate the external PWM or clock input to TPS929120EVM, because both signal
outputs from USD2ANY board are not transmitted to TPS929120EVM if TPS929120CANEVM is
connected.
Figure 4. Hardware Setup with CAN Transceiver
• Connect a 12-V power supply to TP1 (VSUPPLY_EXT) and TP1 (GND).
• Connect USB2ANY tool to PC through USB cable.
• Plug TPS929120CANEVM to USB2ANY tool through the J3 header of TPS929120CANEVM.
• Connect TPS929120CANEVM to TPS929120EVM through the J4 connector of TPS929120CANEVM
and the J7 connector of TPS929120EVM with DB-09 cable.

How to Get Started www.ti.com
6SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
Figure 5. TPS929120EVM Jumper Configurations With TPS929120CANEVM Connected
Table 2. TPS929120EVM Jumpers Setting with
TPS929120CANEVM Connected
HEADER SETTING
J2, J10, J17, J19, J20, J40 Open
J4, J5, J6, J8, J9, J11 Short
J12 Short “FS” to “H”
J13 Short “ADDR2” to “L”
J14 Short “ADDR1” to “L”
J15 Short “ADDR0” to “H”
J16 Short “CANH_C” to “CANH”,
“CANL_C” to “CANL”
J30 Short “OUTx” to “OUTx_MONO”,
where x=0 to 11
All headers paralleled with LEDs Open

www.ti.com How to Get Started
7
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
Figure 6 shows the jumper configurations for TPS929120CANEVM. For header J5, short "+5V" to
"+5V_U2A". For header J6, short "+3.3V" to "+3.3V_U2A".
Figure 6. TPS929120CANEVM Jumper Configurations
3.2 Software Installation
There are two types of the GUI, online version and desktop version.
3.2.1 Run Applications Through Online
Go to the TPS929120-Q1 EVM web page. Scroll down to the "Order Now" section and click the "Start
Evaluation" button to reach to the TPS929120-Q1 gallery page. It might require to login user account
privileges to open the gallery page. All GUI versions are shown ordered from left to right on the gallery
page as shown in Figure 7. Left most application icon shows the latest version. Clicking the application
icon to open the online version GUI. There may be prompt to download and install the browser extension
and TI Cloud Agent for the first time. Follow the steps to install the browser extension and TI Cloud Agent
Applications.
Figure 7. TPS929120-Q1 Gallery Page

How to Get Started www.ti.com
8SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
3.2.2 Run Applications on Desktop
Click the "Download" button under the "Order Now" section to download the TPS929120EVM GUI
installation zip file to local computer, or you can download it from the application icon as showed in
Figure 8 by hovering the cursor over the download button and selecting the appropriate platform. Then
extract the zip folder and install the GUI using the exe - TPS929120-Q1-1.0.5.setup-win_7.3.0. Make sure
the network is connected while installing the GUI.
Figure 8. GUI and GUI Composer Download Page
Follow the on-screen instructions by clicking "Next" button to accept the license, default installation
directory and to install the GUI Composer Runtime engine. You can either provide a location for the
downloaded GUI Composer Installer, or choose to download from the web. The GUI Composer Installer
can be downloaded from the gallery page as showed in Figure 8 by selecting the appropriate platform.
Continue to click on the "Next" button to complete the GUI Composer Runtime installation.
Figure 9. GUI Composer Runtime Installation
After the GUI Composer installation, it continues to install the TPS929120EVM GUI. Follow the on-screen
instructions by clicking the "Next" button to finish the GUI installation. Once installed, a shortcut to the GUI
is found on the desktop and also in the start-up menu under the Texas Instruments folder.

www.ti.com How to Get Started
9
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
3.3 Firmware Update
After opening the GUI, the GUI will try to connect the EVM board. At the moment, the GUI will detect the
firmware version of the connected USB2ANY tool automatically. If the firmware version is not mapping
with the recommended version for the GUI, there is a prompt as shown in Figure 10 to help user update
the firmware in the USB2ANY. Click the update button to begin the firmware update process. After
firmware update succeeds, click finish button to close the prompt window. Then the GUI will try to connect
the EVM board again with the defined device address. Once it connects successfully there will be 3
confirmation sync-up prompt windows, the connected LEDs type (Monochrome or REG), Fail-Safe state (0
or 1) and EEPROM programming Mode (Chip select or External address). For each confirmation window,
just click on the correct image mapping to the current EVM setup.
Figure 10. Firmware Update Prompt Window
If the firmware version of the USB2ANY tool is lower than 2.8.2.0 there will be not firmware update prompt
as showed in Figure 10. We have to upgrade the firmware version to 2.8.2.0 manually. Go to USB2ANY
Interface Adaptor web page, scroll down to "Key Document" section and click "USB2ANY Explorer
Software" to download the installation file. Extract the zip file and install the USB2ANY Explorer using the
"USB2ANY Explorer-2.8.2.0 Setup" exe file. After USB2ANY Explorer installation, open the software with
USB2ANY tool connected to the computer. Please make sure that the GUI is closed while opening the
USB2ANY Explorer. Once the explorer is opened, there will be a "USB2ANY Firmware Requirement"
prompt. Click "OK" button to continue. Follow the instructions on the "USB2ANY Firmware Loader" as
showed in Figure 11 to update the firmware.
After upgrading the USB2ANY firmware version to 2.8.2.0, close the USB2ANY Explorer and open the
TPS929120EVM GUI again. While trying to connect the EVM board, the firmware upgrade window as
showed in Figure 10 will appear.

How to Get Started www.ti.com
10 SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
Figure 11. USB2ANY Firmware Loader
3.4 GUI Function
This section provides instructions to run the TPS929120EVM using the TPS929120EVM GUI.
3.4.1 Connection Status
Make sure to power up the EVM board and connect it to the PC through USB2ANY tool before opening
the on-line version GUI or desktop version GUI. If the GUI has been opened but the USB2ANY has not
been connected to the PC, make sure the USB2ANY has been connected to the powered-up EVM board
when plug it into the PC. Other operation orders may lead to GUI working abnormally. Once it happens,
please refresh the on-line version GUI or re-run the desktop version GUI.
The GUI supports both hardware setups with CAN board connected or not connected. When CAN board
connected, the CAN checkbox on the "Device Address" widget should be checked. When CAN board is
not connected, left the CAN checkbox unchecked. Before changing hardware setup, remove the
USB2ANY cable plug from PC.
Before using the GUI, make sure the hardware is connected successfully. You can check the connection
status on the home page where there is a green check mark on the left side of the TPS929120-Q1 body,
which means the USB2ANY is connected to the computer successfully. If there is a red X mark, it means
the hardware is not connected, you must reconnect the device.
After hardware is connected, either "Hardware Connected" or "Hardware not Connected" shows on the
bottom left corner of the GUI. The button to connect or disconnect the GUI to hardware is also available
there. You can click the button to connect to hardware if hardware is not connected or to disconnect from
hardware while hardware connected.

www.ti.com How to Get Started
11
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
In order to connect the GUI to device successfully, you must set the correct device address on the GUI to
map the real device address. See the TPS929120-Q1 data sheet for instructions to set the device
address. The default device address setting value of the GUI is 0x01 when you open the GUI.
On the EVM board, the ADDR0, ADDR1 and ADDR2 can be configured as High or Low through "J15",
"J14" and "J13" connectors. On the GUI page you can directly enter the specified value through the
"Device Address" widget.
Figure 12. TPS929120EVM GUI Connection Status
3.4.2 Walkthrough Wizard Prompt
The GUI integrated walkthrough wizard prompts for each page to guide user through the GUI instructions.
After selecting one page, clicking the question mark displays the walkthrough wizard that covers each
control operation method on that page.
Figure 13. Walkthrough Wizard Prompt

How to Get Started www.ti.com
12 SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
3.4.3 Quick Start Page
Current operation mode shows on the top left corner of the page. Error flag and global faults icons indicate
the real-time status information of the device. There are two types of LEDs: monochrome LEDs and RGB
LEDS. The LED strings can be controlled individually or simultaneously. For selected LEDs, the PWM
duty-cycle and output current are all adjustable. Once a LED open, short or single LED short-circuit
occurs, the related flag becomes red under the diagnostic details panel. For detailed operation
instructions, see the walkthrough wizard of this page.
Figure 14. TPS929120EVM GUI Quick Start Page
3.4.4 Advanced Page
Figure 15 shows the advanced page where, compared to quick start page, more functions are provided.
On the top left corner of the page, all ADC channel can be selected to update the reading value in real
time. After clicking the "Force Fail Sate" button, the device enters the configured fail-safe state, and the
operation mode changes from normal state to related fail-safe state automatically. Under the "Channel
Diagnostics" panel, LED fault icon updates automatically once a corresponding fault happens. For detailed
operation instructions, see the walkthrough wizard of this page.

www.ti.com How to Get Started
13
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
Figure 15. TPS929120EVM GUI Advanced Page
3.4.5 EEPROM Programming Page
The device supports two programming modes for different applications: either with chip select or external
address select. Figure 16 shows the EEPROM programming page. The programming mode is set as the
method you have configured during sync-up process, which can also be toggled through clicking one of
the programming buttons. All EEPROM registers value can be set on this page. All the configured values
are copied to corresponding shadow registers firstly. After clicking "Start Programming" button, all the
shadow registers values overwrites all related EEPROM registers, which means that only after clicking
"Start Programming" button all the current configuration value really overwrites the corresponding
EEPROM registers. Clicking "Load Default" button sets all current registers with default value as showed
in datasheet. The current register configuration can be saved for future reuse.
Jumping to other pages from the programming page or clicking "Exit PROG mode" button will
automatically force the device exit EEPROM programming mode through clearing CONF_STAYINEEP
method, which means the newly modified EEPROM registers value will not update to corresponding
configuration registers after exiting EEPROM programming mode. CLR_REG can be set through register
map page to update configuration registers with the latest EEPROM registers value immediately. For other
detailed operation instructions, see the walkthrough wizard of this page.

How to Get Started www.ti.com
14 SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
Figure 16. TPS929120EVM GUI EEPROM Programming Page
3.4.6 Registers Page
Figure 17 shows the registers page. All the configuration and EEPROM registers are available on this
page. Clicking on the row of the register automatically updates the corresponding field view on the right
side of the page. The register value can be modified through clicking the "Value" column or double clicking
the "Bits" column. The modified value is effective immediately if "Immediate" function is selected on the
top right corner. The modified value does not take effect until you click "WRITE REGISTER" button with
"Deferred" function selected. Click "READ REGISTER" button only reads the selected register. All
registers' value can be read back or set one time through clicking "READ ALL REGISTERS" or "WRITE
ALL REGISTERS".
Modifying the EEPROM registers' value on the register map page does not overwrite the real EEPROM
registers' value. Real EEPROM registers' value can be modified only through EEPROM programming
page.
Figure 17. TPS929120EVM GUI Registers Page

www.ti.com Board Layout
15
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
4 Board Layout
Figure 18 and Figure 19 show the PCB layout of TPS929120EVM.
Figure 18. Top Layer Routing
Figure 19. Bottom Layer Routing (Mirrored)

Board Layout www.ti.com
16 SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
4.1 Schematic
Figure 20 is the TPS929120EVM schematic.

ADDR0/PWM0
11 ADDR1/PWM1
10 ADDR2/CLK
9
ERR
5
FS
8
GND
3
REF
12
RX
1
SUPPLY
6
TX
4
OUT0 13
OUT1 14
OUT2 15
OUT3 16
OUT4 17
OUT5 18
OUT6 19
OUT7 20
OUT8 21
OUT9 22
OUT10 23
OUT11 24
VCC
2
SUPPLY
7
PAD
25
TPS929120QPWPRQ1
U3
4.7k
R6
GND
4700pF
C13
0.5pF
C12
0.5pF
C11
GND GND
GND
GND
CANL
GND
0.5pF
C3
CANH
GND
RX
TX
GND
GND
FS
OUT11
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT7
OUT8
OUT9
OUT10
OUT6
3
B
5 4
6 1
2
R
G
RGB
D3
REF
ERR
ADDR2/CLK
ADDR1/PWM1
ADDR0/PWM0
OUT0_RGB
3
B
5 4
6 1
2
R
G
RGB
D13
OUT5_RGB 3
B
5 4
6 1
2
R
G
RGB
D23
OUT7_RGB
3
B
5 4
6 1
2
R
G
RGB
D33
OUT10_RGB
4.7µF
C6
0.01uF
C8 GND
VSUPPLY_EXT
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15
17
19
21
23
16
18
20
22
24
J30
GND
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15
17
19
21
23
16
18
20
22
24
J40
OUT11
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT7
OUT8
OUT9
OUT10
OUT6
GND
+5V
RX_CC
GND GND
TX_CC
+5V
+5V
0.5pF
C2
GND
FS
CANL_CCCANH_CC
1 2
3 4
5 6
7 8
9 10
J3
ADDR0/PWM0_U2A
ERR_U2A
RX_U2A TX_U2A
GND
ADDR2/CLK_U2A
ADDR1/PWM1_U2A
1 2
3 4
5 6
7 8
J17
RX
TX
CANL
CANH
RX_CC
TX_CC
CANL_CC
CANH_CC
CANL_C
CANH_C
GND
ADDR0/PWM0ADDR1/PWM1ADDR2/CLK
1 32 45 6
D4
1 32 45 6
D5
1 32 45 6
D6
OUT0_MONO
J22
J23
1 32 45 6
D14
1 32 45 6
D15
1 32 45 6
D16
OUT1_MONO
J31
J32
J33
1 32 45 6
D24
1 32 45 6
D25
1 32 45 6
D26
OUT2_MONO
J41
J42
J43
1 32 45 6
D34
1 32 45 6
D35
OUT3_MONO
J50
J51
J52
1 32 45 6
D7
1 32 45 6
D8
1 32 45 6
D9
OUT4_MONO
J24
J25
J26
1 32 45 6
D17
1 32 45 6
D18
1 32 45 6
D19
OUT5_MONO
J34
J35
J36
1 32 45 6
D27
1 32 45 6
D28
1 32 45 6
D29
OUT6_MONO
J44
J45
J46
1 32 45 6
D37
1 32 45 6
D38
1 32 45 6
D39
OUT7_MONO
J53
J54
J55
1 32 45 6
D10
1 32 45 6
D11
1 32 45 6
D12
OUT8_MONO
J27
J28
J29
1 32 45 6
D20
1 32 45 6
D21
1 32 45 6
D22
OUT9_MONO
J37
J38
J39
1 32 45 6
D30
1 32 45 6
D31
1 32 45 6
D32
OUT10_MONO
J47
J48
J49
1 32 45 6
D40
1 32 45 6
D41
1 32 45 6
D42
OUT11_MONO
J56
J57
J58
OUT3_RGB
OUT1_RGB
OUT2_RGB
OUT4_RGB
OUT8_RGB
OUT6_RGB OUT9_RGB
OUT11_RGB
J21
J10 J11
J5
J6
J4
+3.3V_U2A
J8
VSUPPLY
GND
2.2uF
C4
1
2
3
J2
J9
VCC
TX
RX
TX
RX
CANL_C
CANH_C
A1
1
VCCA
2
A2
3
A3
4
A4
5
A5
6
A6
7
A7
8
A8
9
OE
10
GND 11
B8 12
B7 13
B6 14
B5 15
B4 16
B3 17
B2 18
VCCB 19
B1 20
PAD 21
TXS0108ERGYR
U2
GND
0.1uF
C7
0.1uF
C10
GND
+3.3V_U2A
GND
+5V
ADDR0/PWM0_U2A
ADDR1/PWM1_U2A
ADDR2/CLK_U2A
ERR_U2A
RX_U2A
TX_U2A
ADDR0/PWM0_C
ADDR1/PWM1_C
ADDR2/CLK_C
ERR_C
RX_C
TX_C
OUT0_MONO
OUT5_MONO
OUT7_MONO
OUT10_MONO
OUT3_MONO
OUT11_MONO
OUT9_MONO
OUT6_MONO
OUT8_MONO
OUT4_MONO
OUT2_MONO
OUT1_MONO
GND
GND
GND
GND
1000pF
C29
1000pF
C30
1000pF
C31
1000pF
C26
1000pF
C27
1000pF
C28
1000pF
C35
1000pF
C36
1000pF
C37
1000pF
C44
1000pF
C45
1000pF
C46
1000pF
C53
1000pF
C54
1000pF
C55
1000pF
C38
1000pF
C39
1000pF
C40
1000pF
C47
1000pF
C48
1000pF
C49
1000pF
C56
1000pF
C57
1000pF
C58
1000pF
C32
1000pF
C33
1000pF
C34
1000pF
C41
1000pF
C42
1000pF
C43
1000pF
C50
1000pF
C51
1000pF
C52
1000pF
C59
1000pF
C60
1000pF
C61
1000pFC14
1000pFC15
1000pFC16
1000pFC17
1000pFC18
1000pFC19
1000pFC20
1000pFC21
1000pFC22
1000pFC23
1000pFC24
1000pFC25
VSUPPLY
CANH
CANL
ADDR2/CLK
ADDR1/PWM1
ADDR0/PWM0
RX
TX
ERR
ADDR0/PWM0_C
ADDR1/PWM1_C
ADDR2/CLK_C
RX_C
TX_C
ERR_C
J19
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15
17
19
21
23
16
18
20
22
24
J20
OUT0_RGB
OUT5_RGB
OUT7_RGB
OUT10_RGB
OUT3_RGB
OUT11_RGB
OUT9_RGB
OUT6_RGB
OUT8_RGB
OUT4_RGB
OUT2_RGB
OUT1_RGB
OUT11
OUT10
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT7
OUT8
OUT9
OUT6
OUT11
OUT10
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT7
OUT8
OUT9
OUT6
100k
R5
GND ADDR2/CLK
ADDR1/PWM1
ADDR0/PWM0
+5V
FS
REF
RX
TX
ERR
CANH
CANL
GND
GND
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
J16
0.1uF
C5
8.25k
R3
D1
4.7uF
C1
D2
1
2
3
J12
1
2
3
J14
1
2
3
J15
1
2
3
J13
47.0k
R1
47.0k
R2
1.00k
R4
31.6k
R7
TXD
1
GND 2
VCC
3
RXD
4
NC
5
CANL 6
CANH 7
STB
8
TCAN1042HGDRQ1
U1
1 2
3 4
5 6
7 8
9 10
J18
TP1
VSUPPLY_EXT
TP2
GND
1 32 45 6
D36
Maximum Input Voltage = 40V
Maximum Input Current = 1A
Maximum Output Voltage = 40V
1
3
2
J1
VSUPPLY_EXT
GND
1
2
3
4
5
6
7
8
9
11 10
J7
59.0
R8
59.0
R9
1nF
50V
C9
www.ti.com Board Layout
17
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
Figure 20. TPS929120EVM Schematic Diagram

Board Layout www.ti.com
18 SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
4.2 BOM
Table 3 lists the TPS929120EVM BOM.
Table 3. Bill of Materials (BOM)
DESIGNATOR DESCRIPTION MANUFACTURER PART NUMBER QTY
C1 CAP, CERM, 4.7 uF, 16 V, +/- 10%,
X7R, AEC-Q200 Grade 1, 0805 MuRata GCM21BR71C475KA73K 1
C2, C3, C11, C12 CAP, CERM, 0.5 pF, 50 V, +/- 50%,
C0G/NP0, 0603 Kemet C0603C508C5GACTU 4
C4 CAP, CERM, 2.2 uF, 10 V, +/- 10%,
X5R, 0805 AVX 0805ZD225KAT2A 1
C5, C7, C10 CAP, CERM, 0.1 uF, 16 V, +/- 10%,
X7R, 0603 Kemet C0603C104K4RACTU 3
C6 CAP, CERM, 4.7 µF, 50 V,+/- 10%,
X7R, AEC-Q200 Grade 1, 1206 TDK CGA5L3X7R1H475K160AE 1
C8 CAP, CERM, 0.01 uF, 50 V, +/- 10%,
X7R, 0603 Kemet C0603C103K5RACTU 1
C9 CAP, CERM, 1000 pF, 50 V, +/- 5%,
X7R, AEC-Q200 Grade 1, 0603 Kemet C0603C102J5RACAUTO 1
C13 CAP, CERM, 4700 pF, 100 V, +/- 10%,
X7R, AEC-Q200 Grade 1, 0603 TDK CGA3E2X7R2A472K080AA 1
C14, C15, C16, C17, C18,
C19, C20, C21, C22, C23,
C24, C25, C26, C27, C28,
C29, C30, C31, C32, C33,
C34, C35, C36, C37, C38,
C39, C40, C41, C42, C43,
C44, C45, C46, C47, C48,
C49, C50, C51, C52, C53,
C54, C55, C56, C57, C58,
C59, C60, C61
CAP, CERM, 1000 pF, 50 V, +/- 10%,
X7R, AEC-Q200 Grade 1, 0402 TDK CGA2B2X7R1H102K050BA 48
D1 DIODE, SCHOTTKY, 60V, 3A,
DO214AC Micro Commercial Co SK36A-LTPMSCT-ND 1
D2 LED, Red, SMD OSRAM LS R976-NR-1 1
D3, D13, D23, D33 LED, RGB, SMD OSRAM LRTB GVSG-UEVE-
24+AMAQ-29+SCUC-HR 4
D4, D5, D6, D7, D8, D9,
D10, D11, D12, D14, D15,
D16, D17, D18, D19, D20,
D21, D22, D24, D25, D26,
D27, D28, D29, D30, D31,
D32, D34, D35, D36, D37,
D38, D39, D40, D41, D42
LED, Super Red, SMD OSRAM LS G6SP-CADB-1-1-Z 36
H1, H3, H5, H7, H9, H11 HEX STANDOFF 4-40 ALUMINUM
3/4" Keystone 2204 6
H2, H4, H6, H8, H10, H12 Machine Screw, Round, #4-40 x 1/4,
Nylon, Philips panhead B&F Fastener Supply NY PMS 440 0025 PH 6
H13, H14, H15, H16 Standoff, Hex, Male/Female, 4-40,
Nylon, 1/2" Keystone 4802 4
H17 CABLE ASSY DB09 SHLD BEIGE 2M Assmann WSW
Components AK152-2 1
H18
LED Diffuser Panel (2.42" X 5" X
0.125" UL 94V0 polycarbonate
transparent gray or bronze material.
Must meet or exceed UL94-V0 Lexan
9600 or Makrolon FI or equivalent
ANY MCH044 1
J1 WR-DC DC Power Jack, R/A, TH Wurth Elektronik 694106301002 1
J2, J12, J13, J14, J15 Header, 100mil, 3x1, Gold, TH Sullins Connector
Solutions PBC03SAAN 5
J3 Header(shrouded), 2.54mm, 5x2, Gold,
R/A, TH Sullins Connector Solutions SBH11-PBPC-D05-RA-BK 1

www.ti.com Board Layout
19
SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
TPS929120EVM User's Guide
Table 3. Bill of Materials (BOM) (continued)
DESIGNATOR DESCRIPTION MANUFACTURER PART NUMBER QTY
J4, J5, J6, J8, J9, J10, J11,
J21, J22, J23, J24, J25,
J26, J27, J28, J29, J31,
J32, J33, J34, J35, J36,
J37, J38, J39, J41, J42,
J43, J44, J45, J46, J47,
J48, J49, J50, J51, J52,
J53, J54, J55, J56, J57,
J58
Header, 100mil, 2x1, Gold, TH Sullins Connector
Solutions PBC02SAAN 43
J7 D-Sub, 2.77mm, 9 Pos, Tin, R/A, TH Assman WSW A-DS 09 A/KG-T2S 1
J16 Header, 100mil, 8x2, Gold, TH Samtec TSW-108-07-G-D 1
J17 Header, 100mil, 4x2, Gold, TH Samtec TSW-104-07-G-D 1
J18 Header(shrouded), 2.54mm, 5x2, Gold,
TH Sullins Connector Solutions SBH11-PBPC-D05-ST-BK 1
J19 Header, 100mil, 12x1, Gold, TH Samtec TSW-112-07-G-S 1
J20, J30, J40 Header, 100mil, 12x2, Gold, TH Samtec TSW-112-07-G-D 3
R1, R2 RES, 47.0 k, 1%, 0.1 W, 0603 Yageo RC0603FR-0747KL 2
R3 RES, 8.25 k, 1%, 0.1 W, 0603 Yageo RC0603FR-078K25L 0
R4 RES, 1.00 k, 1%, 0.1 W, 0603 Panasonic ERJ-3EKF1001V 1
R5 RES, 100 k, 5%, 0.1 W, AEC-Q200
Grade 0, 0603 Panasonic ERJ-3GEYJ104V 1
R6 RES, 4.7 k, 5%, 0.1 W, AEC-Q200
Grade 0, 0603 Panasonic ERJ-3GEYJ472V 1
R7 RES, 31.6 k, 1%, 0.1 W, 0603 Yageo RC0603FR-0731K6L 1
R8, R9 RES, 59.0, 1%, 1 W, AEC-Q200 Grade
0, 2512 Stackpole Electronics Inc RMCF2512FT59R0 2
SH-J1, SH-J2, SH-J3, SH-
J4, SH-J5, SH-J6, SH-J7,
SH-J8, SH-J9, SH-J10,
SH-J11, SH-J12, SH-J13,
SH-J14, SH-J15, SH-J16,
SH-J17, SH-J18, SH-J19,
SH-J20, SH-J21, SH-J22,
SH-J23, SH-J24, SH-J25
Shunt, 100mil, Flash Gold, Black Sullins Connector
Solutions SPC02SYAN 25
TP1, TP2 Terminal, Turret, TH, Double Keystone 1502-2 2
U1 Automotive Fault Protected CAN Transceiver With Flexible Data-Rate,
D0008A (SOIC-8) Texas Instruments TCAN1042HGDRQ1 1
U2 8-Bit Bidirectional Voltage-Level Shifter For Open-Drain And Push-Pull
Application, RGY0020A (VQFN-20) Texas Instruments TXS0108ERGYR 1
U3 12-Channel Automotive FlexWire
Driver, PWP0024P (HTSSOP-24) Texas Instruments TPS929120QPWPRQ1 1

Revision History www.ti.com
20 SLVUBM2B–April 2019–Revised December 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Revision History
Revision History
Changes from A Revision (May 2019) to B Revision ...................................................................................................... Page
• Updated Section 3.2.2.................................................................................................................... 8
• Updated Section 3.3 ...................................................................................................................... 9
• Updated Figure 20....................................................................................................................... 16