Texecom Veritas R8 Plus User manual

o400
USER GUIDE
For Service Call Scorpion Group - 01452 525397
THANK YOU FOR VOTING TEXECOM

User Guide Summary User Guide
2 INS046-8
Scorpion Group Security - 01452 525397
User Guide Summary
Full Set Enter Your Code
Press Full
!!!!
"
Part Set Enter Your Code
Press Part Set Number
Press Part
!!!!
#, $, %or &
'
Unset Enter Your Code !!!!
Omit Zones Enter Your Code
Press Full or (Part Set No &) Part
Press Omit
Press Zone Number(s)
Press Prog
!!!!
"or !'
(
!…
)
Reset Enter Your Code
Press Reset
!!!!
*
Chime Zones Enter Your Code
Press Chime
Press Zone Number(s)
Press Prog
!!!!
+
!…
)
Chime On/Off Press Chime +
Test Sounders
& Strobe
Enter Your Code
Press Prog
Enter 05
Press 3 (Internal Sounder)
Press 2 (Strobe)
Press 1 (Bell)
Press Reset
Press Reset
!!!!
)
,-
%
$
#
*
*
Walk Test Enter Your Code
Press Prog
Enter 06
Conduct Walk Test
Press Reset
Press Reset
!!!!
)
,.
Conduct Walk Test
*
*
Change Code Enter Existing Code
Press Prog
Press 60
Enter New Code
Press Prog
Press Reset
!!!!
)
.,
!!!!
)
*

User Guide
INS046-8 3
User Guide
Setting the System
If any zones are left open (e.g. a door ajar) or are ‘in fault’the display
will illuminate the zone light of these zones and sound a repeating series
of bleeps corresponding to the zone number (i.e. Zone 1 bleeps once,
Zone 2 bleeps twice, etc.). If more than one zone is open the bleeps will
correspond to the highest zone number (i.e. if Zone 2 and Zone 6 are
open the control panel will bleep 6 times).
While one or more zones are open the exit timer is suspended. Open
zones that will be closed during exit (e.g. exit zones, like the front door)
may be disregarded. Other open zones should be closed. The exit tone
and exit timer will resume when all zones are closed. If it is necessary to
leave a zone open then it must be omitted (see “To OMIT Zones During
Setting”below). If an open zone cannot be closed then it may be ‘in
fault’. If the fault cannot be corrected contact your alarm company.
Your Installer can program the system so that it can be set using the
"or 'keys without the need to first enter a User code.
To FULL Set the System
Ensure all zones are closed (e.g. windows and doors). Enter your 4
digit code !!!!. The Unset light will flash. Press ". The exit
tone will sound. Leave the premises. When the system has set the exit
tone will stop.
To PART Set the System
Ensure all zones in the intended Part Set area are closed. Enter
your 4 digit code !!!!. The Unset light will flash. Press the
number of the required Part Set Suite #, $, %or &. Press '.
The quiet exit tone will sound. Leave the protected area. When the
system has set the exit tone will stop.
1. If Part Set Suite 1 is desired then it is NOT necessary to press #
before pressing '.
2. After entering your code the Unset light will flash indicating the
control panel is ready to accept a command (e.g. "or
'). If no valid command is entered the system will revert to
unset after 16 seconds.
3. Excluded zones (whether from part set or manual omit) that are
closed will flash during the exit period.
!
!

User Guide
4 INS046-8
To UNSET the System
Enter via a designated entry route. The slow entry tone will start. Enter
your 4 digit code !!!!. The system will unset and the entry tone
will stop.
During the last 10 seconds of the entry period the entry tone will
change from slow to fast.
To OMIT Zones During Setting
It is possible to exclude (omit) or include individual zones during setting.
Enter your 4 digit code !!!!. Press "or enter Part Set
Suite number #, $, %or &and press '. Press (. The exit
tone and exit timer will stop and the display will illuminate the zones that
are about to be armed. Press the appropriate numbered button(s)
!… of the zone(s) to be omitted or included. Press )to
complete the omitting procedure. The system will revert to exit mode.
The exit tone and exit timer will restart.
1. The system may be programmed so that some zones cannot be
omitted.
2. The system will automatically revert to exit mode 16 seconds
after the last key is pressed.
3. Whilst omitting, included zones that are ‘in fault’are indicated by
flashing.
4. Omitted zones that are not ‘in fault’flash during the exit period.
If a zone is illuminated but the system sounds the exit tone (as
opposed to an error tone) then the open zone is omitted.
To Set the System With a Power Fault
Enter your 4 digit code !!!!. Press "or enter Part Set
Suite number #, $, %or &and press '. The system will
sound a repeating series of 10 bleeps. Press (. The display will
illuminate the zones that are about to be armed. Press ,. The Power
light will turn off. Press ). The exit tone and exit timer will restart.
!
!

User Guide
INS046-8 5
To RESET During an Alarm Activation
To silence the alarm enter your 4 digit code !!!!. The internal
and external sounders will stop but the external strobe will continue to
flash. The display will flash the zone light of the zone which first caused
the alarm activation and illuminate the zone lights of all subsequently
opened zones (if any). To cancel the display and stop the external
strobe press *. The system will chime and return to unset.
To RESET After an Alarm Activation
After an alarm activation the internal and external sounders will stop
after a pre-set time. The system will re-arm but the external strobe will
continue to flash. Enter via a designated entry route. The entry tone
will start. Enter your 4 digit code !!!!. The system will unset and
the entry tone will stop. The display will flash the zone light of the zone
which first caused the alarm activation and illuminate the zone lights of
all subsequently opened zones (if any). To cancel the display and stop
the external strobe press *. The system will chime and return to
unset.
If the System Requires an Anti-Code After an Alarm Activation
The system may be programmed to require an Anti-Code after an alarm
activation. You will still be able to silence the alarm by entering your
code as normal. However you will not be able to reset the system
without first obtaining the Anti-Code. The zone lights will display a
random 4 digit sequence. They will flash each digit in turn and then
pause before repeating. Contact the phone number on the last page
with this sequence in order to obtain a 4 digit Anti-Code which will allow
the system to be reset.
To display the zone(s) which caused the alarm press *. The
zone light of the zone which first caused the alarm activation will
flash, and the zone lights of all subsequently opened zones (if any)
will illuminate. To return to the random sequence display press
*again.
The CHIME Facility
When the system is unset it is possible to set one or more zones to
Chime. When a zone is set to Chime the control panel will sound a tone
whenever the zone is entered.
!

User Guide
6 INS046-8
To Program the Zones which CHIME
To program the zones which will chime, enter your 4 digit code
!!!!. The Unset light will flash. Press +. The display will
illuminate the zones that will Chime. Press the appropriate numbered
button(s) !…of the individual zone(s) to be included or excluded.
Press )to turn Chime on (the system will sound the chime tone)
or press *to turn Chime off (the system will sound an error tone).
To Turn CHIME On or Off
To turn Chime on or off press +. The system will sound the chime tone
when Chime is turned on and an error tone when Chime is turned off.
If no zones have been programmed to Chime then turning Chime
on and off will have no effect.
To Test the Sounders and Strobe
The control panel has a test facility to check the operation of the internal
sounder, the external sounder and strobe. Enter your 4 digit code
!!!!. The Unset light will flash. Press ). All the zone lights
will illuminate. Enter ,-. All the zone lights will turn off. The system
outputs may be tested as follows:
Key System Output
&Internal sounder at high level (alarm level)
%Internal sounder at low level (entry/exit level)
$Strobe
#External sounder (bell)
,Turns off all of the above
The zone light corresponding to the number pressed will illuminate.
Press *. All the zone lights will illuminate. Press *again.
The system will return to unset and all the zone lights will turn off.
To Display Log Events
The control panel is capable of recalling the last 7 alarm activations. The
zone light of the zone which first caused the alarm activation will flash,
and the zone lights of all subsequently opened zones (if any) will
illuminate.
!
!

User Guide
INS046-8 7
Enter your 4 digit code !!!!. Press ). All the zone lights
will illuminate. Press &followed by the number corresponding to the
desired event, #being most recent, /being least recent (e.g. to
recall the second most recent event enter &$). On completion press
*, all the zone lights will illuminate. Press *again. The
system will return to unset and all the zone lights will turn off.
To Walk Test the System
The control panel has a Walk Test facility to check the operation of the
system's detection devices. Enter your 4 digit code !!!!. The Unset
light will flash. Press ). All the zone lights will illuminate. Enter ,..
Initially all the zone lights will turn off and the control panel will sound the
quiet exit tone. When any zone is opened the control panel will illuminate
the corresponding zone light. The control panel will in addition sound a
repeating series of bleeps corresponding to the open zone number (i.e.
Zone 1 bleeps once, Zone 2 bleeps twice, etc.). If more than one zone is
open the bleeps will correspond to the highest zone number (e.g. if Zone 2
and Zone 6 are open the control panel will bleep 6 times).
Conduct a walk test by triggering each of the system’s detection devices
in turn and check that the control panel registers the corresponding
zone as open. To terminate Walk Test press *. All the zone lights
will illuminate. Press *again. The system will return to unset and
all the zone lights will turn off.
To Change Your Code
Before changing your code, it is vital that you memorise or
write down the new code you are about to program. Failure to
remember your new code will require an engineer visit to
re-program a new code for you. This may incur a call-out charge.
Enter your existing 4 digit code !!!!. The Unset light will flash.
Press ). All the zone lights will illuminate. Enter .,. All the zone
lights will turn off. Enter your new 4 digit code !!!!. Zone lights
1, 2, 3 and 4 will illuminate in turn as each digit of the new code is
entered. Press ). The system will chime to confirm the new code
has been accepted and all the zone lights will illuminate. Press *.
The system will return to unset and all the zone lights will turn off.
If Your System is Due for Maintenance
The system has a service timer which may be programmed by the
installer to give a reminder when maintenance is due. The reminder may
be either turning Chime on or preventing the system from being set.
Chime may be turned off as previously described. In either case contact
your installer.
!

Installation Details User Guide
INS046-8
Installation Details www.scorpion-group.co.uk
Installation Engineer:
Installation Company:
Address:
Telephone:
Installation Date:
Zone Allocation
Zone Full Set Part Set
1
Part Set
2
Part Set
3
Part Set
4
Area
Protected
1
2
3
4
5
6
7
8
Tick Zones Included in Full & Part Sets
Service Record - For Service Call Scorpion Group Security - 01452 525397
System Due for
Maintenance System Serviced Servicing Engineer
Anti-Code Phone Number
If Required