Texecom PREMIER 48 User manual

Issue 6
Premier 48/88/168
Installation Manual

Contents Premier 48, 88 & 168 Installation Manual
2 INS176
Contents
Contents .................................................................. 2
1. History.................................................................. 4
2. System Overview ................................................ 5
System Architecture ................................................. 5
Control Panels .......................................................... 5
Remote Keypads ...................................................... 6
Zone Expanders........................................................ 6
Output Expanders..................................................... 6
Communicators ........................................................ 6
Other Devices ........................................................... 7
3. Installation ........................................................... 8
Installation Sequence............................................... 8
Control Panel............................................................ 8
Power Supply Ratings............................................ 12
Connecting AC Mains............................................. 12
Connecting Batteries.............................................. 12
Connecting Devices to the Network ...................... 13
Remote Keypads .................................................... 15
8XP Zone Expander ................................................ 16
4 XP Zone Expander ............................................... 17
iProx Module........................................................... 17
60IXD Zone Expander ............................................. 18
OP16 Output Expander........................................... 19
Zone and Output Numbering ................................. 20
Zone Connections .................................................. 21
Auxiliary Tamper Connections............................... 22
Speaker Connections............................................. 22
External Sounder Connections .............................. 22
Panel Outputs 1 - 5................................................. 23
Digicom Outputs 1 - 8............................................. 23
2-Wire Smoke Detector .......................................... 24
Expander Auxiliary Input ........................................ 24
Plug-on Communicators ........................................ 25
RP9 Radio-Pad........................................................ 26
GSM Module ........................................................... 26
AV Module............................................................... 26
ComIP Module........................................................ 26
PC-Com................................................................... 27
UNI-Com ................................................................. 27
PRINT-Com ............................................................. 27
RPD-Com ................................................................ 27
GSM-Com................................................................ 27
Connecting a Computer ......................................... 27
Connecting a Printer .............................................. 27
4. Commissioning and Troubleshooting ............. 28
Commissioning....................................................... 28
Trouble-Shooting.................................................... 28
Reset and Service Messages................................. 30
5. Programming the Control Panel ...................... 31
Introduction ............................................................ 31
Copying and Pasting.............................................. 33
Log Off Engineer .................................................... 33
Resetting the Engineers Code (User 00)............... 33
5.1 Zone Setup ...................................................... 34
Zone Types ............................................................. 35
Zone Attributes 1 .................................................... 36
Zone Attributes 2 .................................................... 36
Attributes for Moment or Latch Keys..................... 37
Attributes for Custom Zones.................................. 37
Zone Areas.............................................................. 37
Zone Text ................................................................ 37
Zone Chime ............................................................ 37
Remote Test Enable ............................................... 37
Zone Wiring ............................................................ 38
DD 243 .................................................................... 38
5.2 Area Programming.......................................... 39
Timers ..................................................................... 39
Arming Modes ........................................................ 40
Area Arm Suites...................................................... 40
Area Suite Text ....................................................... 41
Suite Arm Modes .................................................... 41
Area Options........................................................... 42
Time Arm Area........................................................ 45
Area Text................................................................. 46
5.3 Global Options ................................................47
System Timers........................................................ 47
System Config. ....................................................... 48
System Options ...................................................... 51
Monitor Hardware................................................... 52
Control Timers........................................................ 52
System Text ............................................................ 53
Part Arm Text.......................................................... 53
Holiday Dates ......................................................... 54
Speaker Tones........................................................ 54
PC Output Text ....................................................... 55
Custom O/P Text .................................................... 55
5.4 Keypad Setup .................................................. 56
Keypad Areas ......................................................... 57
Keypad Zone Mapping ........................................... 57
Keypad Options...................................................... 57
Keypad Speaker Volume........................................ 57
Keypad Sounder Options....................................... 57
5.5 Expander Setup............................................... 58
Expander Areas ...................................................... 59
Expander Location Text ......................................... 59
Expander Auxiliary Input........................................ 59
Expander Speaker Volume..................................... 59
Expander Sounder Options.................................... 59

Contents Premier 48, 88 & 168 Installation Manual
INS176 3
5.6 System Outputs...............................................60
Available Outputs....................................................61
Programming Outputs ............................................61
Output Group - Not Used........................................61
Output Group - System ...........................................61
Output Group - Area................................................63
Output Group - Zone...............................................65
Output Group - User Code Entered........................65
Output Group - Control Timer ................................65
Output Group - PC Control.....................................65
Output Group - Door Control..................................65
Output Attributes.....................................................66
X-10 Outputs............................................................66
Custom Outputs ......................................................66
5.7 UDL/Digi Options.............................................67
Reset Digi ................................................................67
Start Test Call..........................................................67
MSN/Pre-Dial No. ....................................................67
Program Digi ...........................................................68
Digi Options ............................................................71
Area Accounts.........................................................71
UDL Options............................................................72
Radio/SMS Options.................................................74
Com Port Setup.......................................................77
Zone Alarm Reporting Codes .................................78
5.8 Setup Users .....................................................84
Default User Codes.................................................85
Programming New Users........................................85
User Types ..............................................................85
User Functions and Options...................................86
User Options 1 ........................................................87
User Options 2 ........................................................87
User Config. ............................................................88
User Time Lock .......................................................88
User Name Text.......................................................88
Door Control............................................................88
Adding Tags ............................................................88
Deleting Users.........................................................88
5.9 Engineer Utilities.............................................89
View Event Log........................................................89
Do Bell Test.............................................................92
Do Walk Test ...........................................................92
View Zone Status ....................................................93
Do System Tests .....................................................93
Confirm Devices .....................................................94
View RKP Status .....................................................94
Check Exp. Status................................................... 94
Set System Time .....................................................95
Set System Date......................................................95
Change Eng. Code..................................................95
Adjust Volumes .......................................................95
Default NVM Data.................................................... 96
Location Text........................................................... 96
Print Log Data ......................................................... 96
Soak Test Areas......................................................96
View iD Data ............................................................ 97
Configure Radio......................................................97
5.10 Programming Part Arms...............................98
Alter Part Arms........................................................ 98
6. Specifications....................................................99
Control Panel ..........................................................99
Remote Keypads...................................................100
Zone Expanders .................................................... 100
Output Expanders ................................................. 101
Standards..............................................................101
Warranty ................................................................ 101
EN50131 Markings................................................101
Declaration of Conformity ....................................102

System Overview Premier 48, 88 & 168 Installation Manual
4 INS176
1. History
This section shows the key milestones in the product development history, helping to identify when particular features were
implemented.
!To confirm the Panel Type and software version, press !followed by "on the keypad. The panel type and software
version will be displayed.
Version 1.3
•Initial release.
Version 3.0
•Radio-Pad supported.
Allows alarm monitoring using the Paknet network.
•SMS signalling supported.
Version 4.0
•Crestron protocol added.
Allows connection and integration with Crestron
home automation equipment via com port.
Version 6.1
•Stand alone iProx supported.
Version 7.0 – Issue 5 Manual
•EN50131 and DD6662 functionality.
Features required for EN50131 and DD6662 added
– eg keypad blanking.
•Triple EOL (anti mask) supoort.
•8XP Expander input programmable as PSU
Monitor.
Version 7.5
•PSU Monitor support.
PSU monitor option on 8XP Expander auxiliary
input.
Premier PSU Monitor.
Premier PSU200XP monitored power supply.
Version 8.0 – Issue 6 Manual
•500 event Mandatory Log added.
•Additional EOL & TEOL circuits supported.
Alternative End-of-Line and Triple-End-of-Line
resistor values supported for compatibility with
other manufacturers products. These are selectable
per zone in the zone setup menu.
•Importing Prox Tags from any panel.
Prox Tags can now be imported from any Premier
Panel as part of the user set up.
•Radio shock sensor supported.
Support for Intelligent Radio Shock Sensor added
in preparation for future introduction.
•Addition of ‘Black Listed’ user codes.
Up to 16 banned user codes can be included in a
‘Black List’ via Wintex.

Premier 88 & 168 Installation Manual System Overview
INS176 5
2. System Overview
System Architecture
8 Programmable
100mA Outputs
Bell Tamper Input
Auxiliary Tamper Input
5 Programmable
A & 1 Relay)
( and only)
Outputs
(4 x 500m
Premier 88 168
Premier
48/88/168
Premier LCD/LCDP
Premier LCDL/LCDLP
4 Wire Data Network 1
16 Programmable
100mA Outputs
4 Keypads ( )
8 Keypads ( )
16 Keypads ( )
Premier 48
Premier 88
Premier 168
Premier OP16
2 Output Modules ( )
4 Output Modules ( )
8 Output Modules ( )
Premier 48
Premier 88
Premier 168
8 Zone Inputs
Alarm Receiving
Centre
Modem
PC and Modem for
Remote Upload/Download
PC-Com
PC and for
Local Upload/Download
PC-Com
Plug on Digimodem
Plug on
(Com300, Com2400
or ComISDN)
Radio-Pad,
GSM Module
2 Zone
Inputs
1Programmable
100mA Output
2 Zone
Inputs
1Programmable
100mA Output
Speaker
Output
4 Wire Data Network 2
( only)Premier 168
Speaker Output
8 Zone Inputs
Auxiliary Input
Premier 8XP
8 Programmable
100mA Outputs
4 Expanders ( )
8 Expanders ( )
16 Expanders ( )
Premier 48
Premier 88
Premier 168
Wire as Network 1
8 to 48 Zones ( )
8 to 88 Zones ( )
8 to 168 Zones ( )
Premier 48
Premier 88
Premier 168
Power
Info.
Ready
Service
Omi
Power
Info.
Ready
Service
Omit
Bell/Strobe Outputs
Area
Yes
Part
Chime
Omit Reset
Menu
2 abc
No
13
def
6 mno
9 wxyz
5 jkl
8 tuv
0
4
ghi
7 pqrs
Area
Yes
Part
Chime
Omit Reset
Menu
2 abc
No
13
def
6 mno
9 wxyz
5 jkl
8 tuv
0
4
ghi
7 pqrs
Premier
Power
NetworkNo
Address
Zones
Power
NetworkNo
Address
Zones
Control Panels
Premier 48
•8 fully programmable Double Pole or End Of Line zones
•Expandable to 48 zones via keypads and zone expanders
•1 x 4-wire data network (standard 7/0.2 alarm cable)
•Up to 4 keypads and 4 zone expanders
•Up to 2 output modules
•4 independent areas each with 3 part arms
•4 area arm suites
•25 programmable User codes
•500 Event Log (time & date stamped)
•2 programmable panel outputs (2 x 1A )
•1.5 Amp power supply
Premier 88
•8 fully programmable Double Pole or End Of Line zones
•Expandable to 88 zones via keypads and zone expanders
•1 x 4-wire data network (standard 7/0.2 alarm cable)
•Up to 8 keypads and 8 zone expanders
•Up to 4 output modules
•8 independent areas each with 3 part arms
•8 area arm suites
•50 programmable User codes
•1000 Event Log (time & date stamped)
•5 programmable panel outputs (4 x 1A & 3A relay)
•2.0 Amp power supply
Premier 168
•8 fully programmable Double Pole or End Of Line zones
•Expandable to 168 zones via keypads and zone expanders
•2 x 4-wire data network (standard 7/0.2 alarm cable)
•Up to 16 keypads and 16 zone expanders (8 per network)
•Up to 8 output modules (4 per network)
•16 independent areas each with 3 part arms
•16 area arm suites
•200 programmable User codes
•2000 Event Log (time & date stamped)
•5 programmable panel outputs (4 x 1A & 3A relay)
•2.0 Amp power supply
Premier 48, 88, and 168
•32 Event Alarm Log
•500 Event Mandatory Log
•8 programmable digicom outputs (100mA each)
•32 character zone text
•Facility for Plug-on Digimodem (Com300/2400/ComISDN)
•Facility for Plug-on Paknet RP9 Radio-Pad
•Facility for Plug-on GSM Module
•Facility for Plug-on IP Module (ComIP/Chiron/WebWayOne)
•Facility for a plug-on RedCARE/RM8 Relay Module
•PC-Com/printer port

System Overview Premier 48, 88 & 168 Installation Manual
6 INS176
Remote Keypads
Premier LCD
•32 character text display
•2 fully programmable DP or EOL zones
•1 fully programmable output (100mA -ve applied)
•Fully adjustable back-lighting, normally bright, dim or off,
changing to bright during entry or following a key press
•Built in piezo sounder
•Programmable ‘Info.’ LED
Premier LCDL
ALL the features of the Premier LCD plus:
•Larger 32 character text display
•Speaker output
Premier LCDP
•Premier LCD with a built in Proximity Tag Reader
Premier LCDLP
•Premier LCDL with a built in Proximity Tag Reader
Premier RKP8/16Plus
•LED Arming keypad
•2 fully programmable EOL zones
•CANNOT be used for Programming
Zone Expanders
Premier 4XP
•4 fully programmable DP or EOL zones
•2 fully programmable outputs (100mA -ve applied each)
•Remotely wired
Premier 8XP
•8 fully programmable DP or EOL zones
•8 fully programmable outputs (100mA -ve applied each)
•Speaker output
•Programmable auxiliary input
•Remotely wired
Premier 60iXD
•2 loops x 30 fully programmable iD zones
•iD biscuit technology
•Plug-on
“iD” is a registered trade mark of Chloride Safety System Limited.
Output Expanders
Premier OP16
•16 fully programmable outputs (100mA each)
•1 fault output (100mA -ve applied)
•Can be connected to mimic panels to give zone indication
•Can be connected to relays and sounders
Premier RM8 Relay Module
•Plug-on relay card (RedCARE footprint)
•8 separate inputs for stand alone operation
•8 x 3Amp relay outputs (n/o, n/c, com)
•Output ‘ON’ LED indication
Communicators
Com300
•Multi-protocol communicator supporting Fast Format,
Contact ID, SIA Level II and EasyCom Pager protocols
•300-baud modem for remote uploading and
downloading using the Wintex UDL software and a PC
•For use with an analogue telephone line (REN = 1)
Com2400
•Multi-protocol communicator supporting Fast Format,
Contact ID, SIA Level II and EasyCom Pager and SMS
Messaging protocols
•2400-baud modem for remote uploading and
downloading using the Wintex UDL software and a PC
•Sends SMS text messages to mobile phones
•For use with an analogue telephone line (REN = 1)
ComISDN
•Multi-protocol communicator supporting Fast Format,
Contact ID, SIA Level II and EasyCom Pager protocols
•300-baud (analogue) or 19200-baud (digital) Modem for
remote uploading and downloading using the Wintex
UDL software and a PC
•For use with an ISDN telephone line
ComIP
•Multi-protocol communicator supporting Fast Format,
Contact ID and SIA Level II protocols via TCP/IP
•High speed modem for remote uploading and
downloading using the Wintex UDL software and a PC
•For use with ADSL/DSL/Broadband/WAN/LAN etc.
RP9 Radio-Pad
•Paknet radio communicator supporting Fast Format and
Contact ID protocols
•4800-baud modem for remote uploading and
downloading using the Wintex UDL software and a PC
GSM Module
•Provides a GSM telephone path for Premier Digital
Communicators
•Sends SMS text messages to mobile phones
•Arm, Disarm, Reset the alarm, turn outputs on and off,
omit zones and send messages to the control panel
using SMS text messages
•9600-baud modem for remote uploading and
downloading using the Wintex UDL software and a PC

Premier 48, 88 & 168 Installation Manual System Overview
INS176 7
Other Devices
PC-Com
•For connecting a PC to the control panel via an RS232
Serial port allowing local uploading and downloading using
Wintex UDL software
USB-Com
•For connecting a PC to the control panel via a USB 1.0 or
2.0 port allowing local uploading and downloading using
Wintex UDL software
UNI-Com
•For connecting a serial device i.e. PC modem or mobile
phone to the control panel
PRINT-Com
•For connecting a serial printer to the control panel
RPD-Com
•For connecting a RP9 Radio-Pad to the control panel
GSM-Com
•For connecting a ComGSM to the control panel
X10-Com
•For controlling X10 enabled devices on the ring main.
Premier Memory Module
•Fits onto the expansion port to provide a 10,000 event
log.
Premier Battery Splitter
•Allows two backup batteries to be connected to a single
set of battery terminals, and will provide appropriate
monitoring and charging for each.
External Sounders
Texecom supply a range of external sounders

Installation Premier 48, 88 & 168 Installation Manual
8 INS176
3. Installation
Installation Sequence
Before attempting to install the alarm system, read this
section. Once you have an overall understanding of the
installation sequence, carefully work through each step.
1: Design the Layout
Make a rough sketch of the premises to get an idea of where
the alarm detection devices, keypads, zone expanders etc.
are to be located.
2: Mounting the Panel
The control panel should be mounted in a dry area close to
an unswitched AC power source and the incoming telephone
line (if using a communicator).
!You must complete all wiring before connecting the
battery or applying AC mains to the control panel.
3: Install the Keypads and Zone Expanders
Mount and connect the keypads, zone expanders and output
modules to the control panel (see page 13 for wiring details).
4: Install the Alarm Detection Devices
Install the detection devices, PIR’s, Contacts, PA Buttons etc.
and connect them to the control panel (see page 21 for wiring
details).
5: Install the External Sounder
Install the external sounder and connect to the control panel
(see page 22 for wiring details).
6: Other Wiring
Complete all other wiring including speakers, telephone line
and output connections etc. (see pages 22 - 23 for details).
7: Applying Power to the Control Panel
Once steps 1 to 6 are completed, power can be applied to
the control panel.
When applying power for the first time, the factory default
settings must be loaded (see page 28 for details). Power
should always be connected in the following order:
•Connect the red battery lead to the positive terminal of
the battery and then connect the black battery lead to
the negative terminal
!The panel will only become ‘live’ when the AC
Mains is connected or the ‘Battery Kick-start’
button is pressed.
•Connect the AC mains
For a complete list of factory default settings, see the Premier
Quick Reference supplied with your panel.
8: Programming the Control Panel
Please refer to section 5 for instruction on programming the
control panel.
9: Testing the System
Test the system thoroughly to ensure that all features and
functions operate as required (see page 89 for details).
Control Panel
Mounting
Mount the control panel on a flat, plumb wall using at least
three screws of appropriate size.
!It is essential to ensure that none of the fixing slots or
cable entries are accessible after fixing.
Mains cabling must be secured (e.g. with a cable tie) to
one of the anchor points provided.
Wiring the Control Panel
WARNING: ELECTRICITY CAN KILL
BEFORE connecting the control panel ALWAYS
disconnect the supply at the consumer unit.
If in ANY doubt consult a qualified electrician.
"IMPORTANT SAFETY INFORMATION. HAZARDOUS
VOLTAGES INSIDE, NO USER SERVICEABLE PARTS,
NO USER ACCESS.
!ONLY connect the mains supply to the mains terminal
block, NEVER connect the mains supply directly to the
PCB.
ALWAYS refer to National Wiring Regulations when
conducting installation.
An appropriate and readily accessible disconnection
device (e.g. an unswitched fused spur) MUST be
provided as part of the installation.
The disconnection device must NOT be fitted in a
flexible cord.
Where identification of the neutral in the mains supply
is NOT possible a two-pole disconnection device
MUST be used.
The building mains supply MUST incorporate
appropriate short-circuit backup protection (e.g. a fuse
or circuit breaker) of High Breaking Capacity (HBC, at
least 1500A).
Use mains cable of adequate carrying capacity for the
rated current (i.e. at least 0.75mm2).

Premier 48, 88 & 168 Installation Manual Installation
INS176 9
Control Panel Layout
1.5 Amp Mains
Transformer
Control Panel
Circuit Board
Space for
1
2 x 7Ah Batteries
or 1 x 17Ah Battery
x 7Ah Battery
Cable
Entries
Plug-on
Digimodem
(
or
Com300,
Com2400
ComISDN)
Mains Terminal
Block & Cable Entry
Tamper
Switch
Cable
Entries
BT
Cable
Entry
T
R
T1
R1
Com 2
F1
F4
F5
JP7
Aux 12v
1Amp
Network 2
1Amp
Com 1
Heartbeat
JP2
Jp9
Load
Defaults
Expansion
JP6
Engineer
Remote
F3
Network 1
1Amp
Bell/Strb - 1Amp
Kick
Start
Tx1 Rx1 Tx2 Rx2
OP1-
Aux
Ta m p
Ta m p
OP5
N/O COM N/C
Spk+
Spk
-
+12v
Bell -
Strb -
0v
OP2-
OP3+
OP4+
Zone 6
T
A
Zone 7
T
A
Zone 8
T
A
Zone 5
T
A
Zone 3
T
A
Zone 4
T
A
Zone 2
TA
Zone 1
T
A
NETWORK 2NETWORK 1
+ - T R + - T R
Aux v 12
-
+
Box
Tamp
BATT
A.C.
DC+
L/M
R/R
DC
-
2
3
5
6
7
8
4
1
DIGICOM OUTPUTS
+
-
V
1
00mA =
1 Amp

Installation Premier 48, 88 & 168 Installation Manual
10 INS176
Control Panel PCB Layout
Com 2
F1
F4
F5
JP7
Aux 12v
1Amp
Network 2
1Amp
Com 1
Heartbeat
JP2
Load
Defaults
Expansion
JP6
23
13
Engineer
Remote
518
15
F3
Network 1
1Amp
17
14
Bell/Strb - 1Amp
Kick
Start
Tx1 Rx1 Tx2 Rx2
OP1-
Aux
Tamp
Tamp
OP5
N/O COM N/C
Spk+
Spk
-
+12v
Bell -
Strb -
0v
10
21
11
9
12
OP2-
OP3+
OP4+
Zone 6
T
A
Zone 7
T
A
Zone 8
T
A
Zone 5
T
A
Zone 3
T
A
Zone 4
T
A
Zone 2
TA
Zone 1
T
A
NETWORK 2
8
6
NETWORK 1
+ - T R + - T R
Aux v 12
-
+
7
20
19
Box
Tamp
BATT
A.C.
DC+
L/M
R/R
DC
-
2
3
5
6
7
8
4
1
DIGICOM OUTPUTS
1
3
4
2
+
-
V
1
00mA =
1 Amp
22
15
16
1: AC Input
Connected to the 16.5V transformer.
DO NOT CONNECT THE MAINS SUPPLY TO THE AC
INPUT TERMINALS ON THE PCB.
2: Battery Connections
A 12V rechargeable battery must be connected to these
terminals in order to provide continuous system operation in
the event of an AC Mains failure (see page 12 for details).
3: Digicom Power & Inputs
These terminals provide unfused power; remote reset and line
fault inputs and are normally used for connecting a stand-alone
communicator to the control panel (see page 23 for details).
4: Digicom Outputs
Outputs 1 to 8 are low current (100mA ‘-ve’ applied) and
would normally be used when connecting a stand-alone
communicator to the control panel (see page 23 for details).
Each output is fully programmable (see page 61 for details).
5: Engineers Keypad
A portable Engineers keypad can be plugged on here to
allow easier access for programming and testing.
!When using a keypad as an Engineers keypad, the
address must be set to ‘10’ (see page 15 for details).
The keypad zones and lid tamper are not monitored.
6: Network Data Connections
Networks 1 & 2 provide connection for the keypads and
zone expanders (Network 2, Premier 168 only). The ‘+’ and
‘–’ terminals provide power whilst the ‘T’ transmits data and
‘R’ receives data (see page 13 for details).
7: Auxiliary 12V Power
These terminals are for connecting devices that require 12V
power (protected by a 1A fuse).
8: Programmable Zones 1 - 8
These terminals provide the connections for the zones (see
page 21 for wiring details). Each zone is fully programmable
(see page 34 for details).
9: External Sounder Connections
These terminals are used for connecting to an external
sounder unit (see page 22 for details).
10: Auxiliary Tamper Connections
These terminals can be used for monitoring the tamper loop of
an auxiliary device (see page 22 for details).
11: Loudspeaker Connections
These terminals can be used for connecting up to one 16Ω
or two 8Ω loudspeakers (see page 22 for details).
12: Panel Outputs
Outputs 1 & 2 are 500mA ‘-ve’ applied, outputs 3 & 4 are
500mA ‘+ve’ applied and output 5 is a clean contact relay
(see page 23 for wiring details). These outputs are all fully
programmable (see page 60 for details).
!Panel outputs 3, 4 and 5 are only available on the
Premier 88 and 168.
13: Plug-on Communicator Connections
This socket provides connection for Premier plug-on
communicator (see page 25 for details).
14: Box Tamper Connection
The box tamper micro switch is connected here. The micro
switch provides tamper protection for the main control panel in
case of unauthorised access. To disable the box tamper,
remove the micro switch lead and fit a jumper link across the
two pins.

Premier 48, 88 & 168 Installation Manual Installation
INS176 11
15: Plug-on RedCARE/Dualcom Connections
These pins provide connections for a plug-on RedCARE,
Dualcom, Digicom or RM8 Relay module. Each output is fully
programmable (see page 61 for details).
!When a device is plugged on to these pins, not all
outputs may be available, please refer to the relevant
documentation for details.
16: Battery Kick-start Button
When powering up the panel without AC Mains present, this
button must be pressed in order to connect the battery.
!If AC Mains is present this button does not need to be
pressed.
17: Communication Ports
Com Port 1 is a serial communications port and can be used
for connecting a PC running Wintex or any supported serial
device to the control panel (see page 77 for details).
Com Port 2 is a serial communications port and can be used
for connecting a PC running Wintex or any supported serial
device to the control panel (see page 77 for details).
Com Port 3 is a serial communications port and can be used
for connecting a PC running Wintex or any supported serial
device to the control panel (see page 77 for details).
18: Network Data Indicators
The red LED indicates that data is flowing out of the control
panel and normally flashes very quickly. The green LED
indicates that data is flowing into the control panel and
normally flashes slowly, the green LED flashes faster as
more devices are connected (see page 13 for details).
19: Load Defaults Button
Press and hold this button whilst applying power to the
control panel to load the factory default settings. Press and
hold this button for 7 seconds with power already on the
panel to restore just the Engineer code to the factory setting
of #$%".
!Loading the factory defaults can take up to 60
seconds to complete.
Loading defaults will only be possible if the NVM has
not been locked (see page 49 for details).
For a complete list of factory defaults, see the Premier
Quick Reference supplied with your panel.
20: Expansion
The Expansion Port can be used for connecting a 60XPiD
Zone Expander (see page 18 for details) or an AV Module
(see page 26 for details).
21: Heartbeat LED/Power Light
Flashes steadily to indicate that the control panel is
functioning correctly. If the light is ON or OFF all the time,
then there could be a problem (see page 28 for details).
22: Current Reading Pads
To calculate the current draw of the control panel, measure
the voltage across the two pads and multiply by 10 i.e.
Reading = 34mV (x10) = 340mV = 340mA.
23: NVM 1 & 2
All system programming data and the event log is stored in
one or two removable non-volatile memory devices.
F1 - F5: Protection Fuses (Premier 48, 88 and 168)
The following fuses are provided:
•F1 (1Amp) Auxiliary 12V Power fuse
•F2 (1.6 Amp) Battery fuse (electronic PTC)
•F3 (1 Amp) Network 1 fuse
•F4 (1 Amp) Bell/Strobe fuse
•F5 (1 Amp) Network 2 fuse (Premier 168 only)

Installation Premier 48, 88 & 168 Installation Manual
12 INS176
Power Supply Ratings
If installing to PD6662, the system standby times in the event
of a mains power failure vary depending on the grade and
how AC fail is signalled:
System Standby Times
Grade 2 Grade 3
AC Fail signalled
as AC Fail
Grade 3
AC Fail signalled
as Fault
12 Hours 12 Hours 24 Hours
The “Rated Power” of the control panel will depend on the
size of the standby battery, standby time and the installation
grade:
7 Ah Standby Battery
Max Power
Available
from control
panel
Grade 2 –
Rating
Grade 3 –
Rating
AC Fail
signalled as
AC Fail
Grade 3 –
Rating
AC Fail
signalled as
Fault
2 A 580mA 580mA 290mA
17 Ah Standby Battery
Max Power
Available
from control
panel
Grade 2 –
Rating
Grade 3 –
Rating
AC Fail
signalled as
AC Fail
Grade 3 –
Rating
AC Fail
signalled as
Fault
2 A 1.25A 1.25A 710mA
When calculating the current consumption of the system you
must include the current taken by the control panel and all
the devices that it powers. If the total current exceeds the
“Rated Output” for the grade you are installing to then an
additional power supply is required.
Connecting AC Mains
The AC Mains supply is connected to a 3 way ‘Euro Type’
fused terminal block, which is fitted with a 125mA or 500mA
fuse.
!All other wiring MUST be carried out before AC mains
is connected to the control panel.
After connecting the AC Mains, fit the mains cover, this
can be found in the spares bag.
L
E
N
To t r a n s f o r m er
Connecting Batteries
If installing to PD6662: 2004 then only One 12V 7Ah battery
or 12V 17Ah battery can be fitted inside the control panel to
provide continued operation in the event of an AC mains
failure, otherwise, two 12V 7Ah batteries can be connected.
!All other wiring MUST be carried out before the battery
is connected to the control panel.
Connect the red battery lead to the positive terminal of the
battery and then connect the black battery lead to the
negative terminal.
!The panel will only become ‘live’ when the AC Mains is
connected or the ‘Battery Kick-start’ button is pressed.
+
-
Battery
12V 7Ah Battery
+
_
+
-
OR
Battery
12V 17Ah Battery
+
_
+
+
-
-
Battery
12V 7Ah Battery
12V 7Ah Battery
+
_
OR
If not installing to PD6662: 2004
!Two batteries can be fitted and still comply with
PD6662:2004 if the Premier Battery Splitter is used.

Premier 48, 88 & 168 Installation Manual Installation
INS176 13
Connecting Devices to the Network
Before connecting keypads, zone expanders and output
modules, isolate ALL power from the control panel (AC Mains
& Battery). Do not continue if there is still power present on
the control panel.
!Connecting devices with power still present on the
control panel may damage the device or control panel
and invalidate any warranty.
Keypads, zone expanders and output modules are all connected
to the same network terminals located at the bottom left hand
corner of the control panel and may be connected serially (daisy
chain), in parallel (star) or any combination of the two (see
Figure 1, page 14 for details).
!No more than 8 zone expanders, 8 keypads and 4 output
modules can be connected to each network.
The maximum number of devices that can be connected
in total will depend on the control panel fitted.
Whenever new devices are connected to the networks, they
must be confirmed onto the system using the ‘Confirm
Devices’ menu option (see page 94 for details).
Wiring the Network
The networks are made up of four terminals incorporating
power and data. To ensure correct operation, all four
terminals on the device must be connected to the
corresponding terminals on the control panel, or previous
device (see Figure 1, page 14 for details). The table below
shows each terminal and its description:
Terminal Description
+ +12V Supply
- 0V Supply
T Transmit Data
R Receive Data
Devices can be connected using 4-core cable. However, it is
recommended that 6 or 8-core cable is used as the spare cores can
be used to ‘Double Up’ on the power connections if needed.
!Standard 7/0.2 alarm cable can be used for most
installations. However, under certain conditions it may
be necessary to use screened cable.
Cable Distances
The maximum recommended distance for devices when
using standard 7/0.2 alarm cable is:
•250m for each branch when using the star (parallel)
configuration
•When using a daisy chain (series) configuration the
maximum distance will depend on the number of devices
connected on the chain. The more devices that are
connected, the shorter the distance to the last device
(this is due to voltage drop in the cable)
Whichever method of wiring configuration is used, ensure
that the voltage between the ‘+’ and ‘–’ terminals at each
device is no lower than 10.0V when the system is running on
the standby battery.
The table below shows maximum cable runs when one
keypad or expander is installed using standard 7/0.2 alarm
cable with various loads:
Configuration Max. Cable Run
1. Keypad + 2 PIR’s @15mA 250m
2. Expander + 2 PIR’s @15mA 250m
3. Expander + 8 PIR’s @15mA 100m
4. As No. 3 + 16ΩSpeaker 30m
Distances of up to 1km can be achieved between the control
panel and a device. However, a power supply must be installed
close to the device to power it locally, this will help to
overcome voltage drop caused by the long cable run.
Overcoming Voltage Drop
There are several ways to overcome voltage drop:
•Use thicker lower resistance cable. Standard 7/0.2 alarm
cable has a resistance of 8Ωper 100m
•Double up on the power connections – this will require
using a 6 or 8-core cable rather than a 4-core cable
•Install a power supply to power the device locally,
remember to common the two negative connections
Installing a Power Supply
When a power supply is installed, the 0V connections on the
power supply must be connected through to 0V on the
control panel and the +12V connection between the control
panel and the device must be disconnected (see Figure 2,
page 14 for details).
Network Diagnostics
Each network has two LED’s to indicate data flow. The red
LED indicates data flowing out of the ‘T’ terminal and the
green LED indicates data flowing into the ‘R’ terminal. The
table below shows each LED status and its meaning:
LED Status ‘T’ Wire OUT ‘T’ Wire IN
Red LED Flashing Normal Normal
Red LED On Panel Fault Cable Short
Red LED Off Panel Fault Panel Fault
LED Status ‘R’ Wire OUT ‘R’ Wire IN
Green LED Flashing Panel Fault Normal
Green LED On Panel Fault Cable Short
Green LED Off Normal No Data From Devices
!The LED’s are provided as an aid for fault finding and
therefore should not be completely relied upon to
indicate that there is a fault.

Installation Premier 48, 88 & 168 Installation Manual
14 INS176
Figure 1: Network Connections (250m without additional power supply).
Figure 2: Network Connections (1km with additional power supply).

Premier 48, 88 & 168 Installation Manual Installation
INS176 15
Remote Keypads
Keypad Layout
Zone 2
TA
Zone 1
T
A
NETWORK
+
TR
-
O/P
Address
Switch
Output
Network
Terminals
Tamper
Switch Speaker
Output
Zones
Piezo
Sounder
2431
On
SPK
Connecting Keypads
Keypads are connected to the network terminals located at
the bottom left hand corner of the control panel (see pages
13 & 14 for details).
Keypad Addressing
Each keypad must be assigned a different address using the
DIL switches located on the left hand side of the PCB. The
table below shows the keypad addressing:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On or off Off Off Off 2 431
2 Off On Off Off
2 431
3 Off Off On Off 2 431
4 Off Off Off On 2 431
5 * On Off Off On 2 431
6 * Off On Off On 2 431
7 * Off Off On On
2 431
8 * On Off On On
2 431
Engineers On On On On
2 431
!Never set two keypads on the same network to the
same address.
When using a keypad as an Engineer’s keypad, the
DIL switches must all be ‘On’.
* Premier 88 and 168 only
Keypad Zones
The keypad has two programmable zones (see page 21 for
details). Each zone is also fully programmable (see page 34
for details).
Zone Numbering
The table below shows the zone allocation when the keypads
are installed:
Address Zones
(Network 1)
Zones
(Network 2)
1 Unmapped Unmapped
2 Unmapped Unmapped
3 Unmapped Unmapped
4 Unmapped Unmapped
5 * Unmapped Unmapped
6 * Unmapped Unmapped
7 * Unmapped Unmapped
8 * Unmapped Unmapped
!The zones inside the keypads are not seen by the
system until they have been mapped to a zone number
(see page 57 for details).
* Premier 88 and 168 only
Keypad Output
The remote keypad has one programmable output, which
can be used to drive auxiliary devices such as LED’s,
sounders or relays etc. Wire as per Panel Outputs shown on
page 23 (see page 60 for details). The electrical
characteristics for the output are shown below:
Output Max Current Type
1 100mA Switched -ve
Keypad Speaker Output (LCDL/LCDLP Only)
The Premier LCDL and Premier LCDLP keypads have an
output that can be used for driving up to one 16Ωor two 8Ω
loudspeakers (see page 22 for details).
!The speaker volume is also fully adjustable (see page
57 for details).
Programmable ‘Info.’ LED
The ‘Info.’ LED on the front of the keypad can be
programmed to mimic the keypad output or show the armed
status of an area (see page 57 for details).
Adjustable Backlighting
To adjust the keypad backlighting press the YES key for 5
seconds, then with the YES key still pressed use &to
increase or decrease the backlighting until the required
brightness is achieved, then release both keys.
!The backlight can only be adjusted when the keypad is
not in a menu.
Keypad Lid Tamper
The lid tamper of each keypad can be disabled if required
using the relevant keypad option in the Keypad Setup menu
(see page 57 for details).

Installation Premier 48, 88 & 168 Installation Manual
16 INS176
8XP Zone Expander
Expander Layout
Zones
5 & 6
Power LED
Tamper
Switch
Engineers
Keypad
Interface
Network
Terminals
Aux
12V
Aux
12V
Zones
7 & 8
Zones
1 & 2
Zones
3 & 4
Outputs
1 to 8
Speaker
Output
Aux
Input
Com Port
123
OUTPUTS
45678
Zone 6 Zone 5
Aux 12v
-
Zone 8 Zone 7
T
AT
AT
AT
A
NETWORK IN
+-TR +-TR
NETWORK OUT
Remote
Power
Zone 2Zone 1
TA
Aux 12v
-
+
Zone 4Zone 3
TATATA
Aux
Input
-
Spk
-
+
1
ON
2 3 4
PSU
DS
YPE0123456
Tamper
Disable
Address
Switch
Connecting Expanders
Expanders are connected to the network terminals located at
the bottom left hand corner of the control panel (see pages
13 & 14 for details).
Expander Addressing
Each Expander must be assigned a different address using
the DIL switches located in the centre of the PCB. The table
below shows the expander addressing:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On or off Off Off Off 2 431
2 Off On Off Off
2 431
3 Off Off On Off 2 431
4 Off Off Off On 2 431
5 * On Off Off On 2 431
6 * Off On Off On 2 431
7 * Off Off On On
2 431
8 * On Off On On
2 431
!Never set two expanders on the same network to the
same address.
* Premier 88 and 168 only
Expander Zones
The expander has eight programmable zones (see page 21
for wiring details). Each zone is also fully programmable (see
page 34 for details).
Zone Numbering
The table below shows the zone allocation when the
expanders are installed:
Address Zones
(Network 1)
Zones
(Network 2)
1 9 - 16 73 - 80
2 17 - 24 81 - 88
3 25 - 32 89 - 96
4 33 - 40 97 - 104
5 * 41 - 48 105 - 112
6 * 49 - 56 113 - 120
7 * 57 - 64 121 - 128
8 * 65 - 72 129 - 136
!Network 2 can only be used on the Premier 168.
* Premier 88 and 168 only
Expander Auxiliary Input
The expander has one programmable input. This auxiliary input
can be used to monitor auxiliary devices such as tamper loops
etc. Wire as per Aux Tamper shown on page 22 (see page 59
for details). The system will respond as follows:
Input Status System Response
0V Applied Input Secure
0V Removed Input Active
EOL Various *
!For further details on how the input status affects the
system please refer to page 59.
* For wiring details, see page 24.
Expander Outputs
The zone expander has eight programmable outputs, which
can be used to drive auxiliary devices such as LED’s,
sounders or relays etc. Wire as per Panel Outputs shown on
page 23 (see page 60 for details). The electrical
characteristics for the outputs are shown below:
Outputs Max Current Type
1 to 8 100mA Switched -ve
Expander Speaker Output
The expander has an output that can be used for driving up to
one 16Ωor two 8Ωloudspeakers (see page 22 for details).
Expander Com Port
The Com Port can be used to connect a PSU200 montored
power supply or a RadioPlus Inteligent Receiver.
Expander Lid Tamper
The lid tamper of each expander can be disabled if required
by fitting a jumper link across the centre and right hand pins
of the ‘Enable Tamper’ pins (JP2) leaving the left hand pin
free. These pins are located to the left of the address DIL
switch just beneath the fuse.

Premier 48, 88 & 168 Installation Manual Installation
INS176 17
4XP Zone Expander
Expander Layout
NETWORK IN
+-TR +-TR
NETWORK OUT
JP1
Zone
2
Zone
1
TA
Aux 12v
-
+
Zone 4Zone 3
TATATA
1
ON
2 3 4
O/P O/P SPK+ SPK-
2- 1-
Engineers Keypad
JP4
DS
JP2
Network IN
Terminals
Network OUT
Terminals
Outputs 1&2 Loud Speaker Terminals
Tamper Switch
Power LED
Address Switch
Zones
1 & 2
Zones
1 & 2
Aux 12V
Engineers Keypad
Interface
Com Port
Connecting Expanders
Expanders are connected to the network terminals located at
the bottom of the control panel (see pages 13 & 14 for
details).
Addressing
4XP expanders are addressed as one or (normally) two
keypads on the network. Each 4XP has to have a unique
address, which must not conflict with any keypad or any
other 4XP on the same network.
The following table shows the expander addresses & the
keypad slots that each would occupy.
Address DIL 1 DIL 2 DIL 3 DIL 4 Keypads
1 On off off off 1 & 2
2 off On off off 2 & 3
3 off off On off 3 & 4
4 off off off On 4 & 5
5 On off off On 5 & 6
6 off On off On 6 & 7
7 off off On On 7 & 8
8 On off On On 8
Zones
The 4XP provides 4 alarm zones, 2 for each of the 2 keypad
slots it occupies. Each zone is fully programmable (see page
48) and has to be mapped to the system (see page 57).
Outputs
2 Programmable outputs are provided 1 for each of the 2
keypad slots occupied by the expander (see page 60 for
output programming)
Expander Speaker Output
One speaker output is provided for connecting one external
16Ωor 2 8Ωloudspeakers (see page 22 for details).
The speaker volume is programmed through the keypad setup
menu (see page 57)
!The speaker is available on keypad 1 of the two
keypad slots the 4XP occupies. (ie if the 4XP address is
5, the speaker will programmed as belonging to
keypad 5).
Expander Com Port
The Com Port can be used to connect a RadioPlus
Inteligent Receiver.
iProx Module
iProx Layout
PIP0123456
Options
1
ON
2 3 4
1
ON
2 3 4
Address
RTE N/C N/O
Com
+
TR
Spk
+
D0
D1
C1
L1-
C2
L2- L+
Tamper
Ext Coil
Remote LED’s Relay 1
Ext Int Ext Int
Internal Sounder
Off
On
Door Strike
Relay
Request to
Exit Input
Remote
Prox Coil
Connections
Speaker
Volume Adj
Network
Terminals
Wiegand
Interface
Connections
Speaker
Terminals
Option & Address Switches
Connection
The iProx Module is connected to the network terminals
located at the bottom of the control panel (see pages 13 &
14 for details).
Addressing
The iProx Module is addressed as a keypad and will occupy
a keypad slot on the network. The unit must have a unique
address, which must not conflict with keypad or any other
iProx Module on the same network
The following table shows the addressing:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On off off off
2 off On off off
3 off off On off
4 off off off On
5 On off off On
6 off On off On
7 off off On On
8 On off On On
Refer to the iProx Module manual for programming and
operating instructions.

Installation Premier 48, 88 & 168 Installation Manual
18 INS176
60iXD Zone Expander
The 60iXD expander provides the following facilities:
•Two iD loops each supporting up to 30 biscuits
•Fused 12V output for powering detectors
•Engineer’s keypad port for local iD diagnostics
!The 60iXD expander module is only supported on Premier
88/168 control panels from version 5.0 onwards and
Premier 48 from version 2.0 onwards. The Premier 48 can
only support a maximum of 48 zones/biscuits.
Installation
Before connecting the 60iXD expander module, isolate ALL
power from the control panel (AC mains and battery), do not
continue if there is still power present on the control panel.
1. Connect the iD expander to the control panel, see
60iXD installation manual (INS261) for details.
2. Connect the iD devices to the expander module, see
“iD Connections”.
3. Reapply power to the control panel and program the
necessary options on the panel see 60IXD
installation manual (INS261) for details.
iD Connections
Each iD biscuit is connected across a two-wire detector loop.
Apart from observing the correct polarity, any wiring
configuration can be used, as shown in the diagram below:
60iXD
LOOP 1
+-
09 10 11 12 13
03 04 05 0601 02
08
07
14
LOOP 2
+-
As LOOP 1
* The 60iXD expander module is supplied with 4 off 10nF
capacitors in the spares pack. It is recommended that you
connect a 10nF capacitor approximately at the half way
point of each iD spur. It is especially important to do this on
iD spurs that are less than 30 metres.
Cabling Considerations
The iD loop can be wired using standard 4-core alarm cable,
this allows 2 cores to be used for the iD biscuit and 2 cores
for supplying 12V power for PIR's etc.
The number of biscuits that can be connected per cable run
is determined by the impedance of the cable used. Standard
4-core alarm cable (7/0.2mm) has a resistance of
approximately 8 Ohms per 100 metres. The following table
shows the maximum number of biscuits that can be
connected at the end of a single cable run using standard 4-
core alarm cable:
Cable Length Maximum Number of Biscuits
100m 30
200m 15
400m 7
800m 3
If a different type of cable is used, the distances should be re-
calculated. e.g., if 7/0.4mm cable is used, a single run of
200m would support 30 devices on the end as the resistance
of the cable is halved.
When installing the iD loop it is usually more practical to run
several cables from the expander module to the different
areas of protection. This effectively reduces any distance
problems and makes fault finding much easier.
To reduce the risk of induced interference and wherever
possible, cables should not be positioned along side mains
power, telephone or other data transmission cables, or run
within the same ducting or trunking as any other cables.
The wiring for the system’s internal sounders (loudspeakers)
should not be connected in the same multi-core as the iD
loop.
Biscuit Connections
Each iD biscuit is identified by its own number 01 to 30 and
contains its own internal sensor that is continuously
monitored by the expander module. The diagram below
shows the connections to the biscuit for monitoring both
tamper and alarm contacts.
iD Biscuit
Alarm
Ta m p e r
LOOP +
LOOP -
White
Yellow
Blue
Biscuit iD
01
When the tamper switch is opened, the iD biscuit is taken
offline and a tamper condition is generated by the control
panel. If the alarm switch is opened the biscuit's internal
sensor changes state and the control panel will see this as an
active condition and will respond as appropriate.
The diagram below shows the typical wiring of a biscuit to a
standard PIR.
+12V
ALARM TAMPER
From Expander To next detector
Red
Black
Blue
Yellow
Red
Black
Blue
Yellow
White
Blue
Yellow
0V
“iD” is a registered trade mark of Chloride Safety System Limited.

Premier 48, 88 & 168 Installation Manual Installation
INS176 19
OP16 Output Expander
Output Module Layout
Power LED
Ta m p e r
Switch
Network
Te rm i na l s
A
ux 12V
and Tamper
Output
NETWORK IN
+- TR +- TR
NETWORK OUT
Power
1Amp Aux 12v
1
A
mp
2431
BANK 1
Remote
Bank 2
Outputs
1 to 8
1
2
3
4
5
6
7
8
BANK 2
1
2
3
4
5
6
7
8
BANK 1
Bank 1
Outputs
1 to 8
Tmp
-
Aux 12V
++
-
2431
BANK 2
Network
Ter m i na ls
Engineers
Keypad
Interface
Connecting Output Modules
Output modules are connected to the network terminals
located at the bottom left hand corner of the control panel
(see pages 13 & 14 for details).
Output Module Addressing
Each output module must be assigned a different address
using the DIL switches located in the centre of the PCB.
The table below shows the expander addressing:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On or off Off Off Off 2 431
2 Off On Off Off
2 431
3* Off Off On Off 2 431
4* Off Off Off On 2 431
5 ** On Off Off On 2 431
6 ** Off On Off On 2 431
7 ** Off Off On On
2 431
8 ** On Off On On
2 431
* Premier 88 and 168 only
** Premier 168 only
!In order for an output module to mimic zone expander
outputs, the output module must be addressed the
same as the zone expander that it is mimicking.
Any combination of addresses can be used on each
output module i.e. Bank 1 can be addressed to mimic
expander 3 and Bank 2 can be addressed to mimic
expander 8.
Bank 1 switch sets the address of the device that Bank
1 outputs 1 to 8 will mimic.
Bank 2 switch sets the address of the device that Bank
2 outputs 1 to 8 will mimic.
Output Module Numbering
The table below shows the output allocation when the output
modules are installed:
Address Outputs
(Network 1)
Outputs
(Network 2) **
1 Expander 1, 1 - 8 Expander 1, 1 - 8
2 Expander 2, 1 - 8 Expander 2, 1 - 8
3 * Expander 3, 1 - 8 Expander 3, 1 - 8
4 * Expander 4, 1 - 8 Expander 4, 1 - 8
5 ** Expander 5, 1 - 8 Expander 5, 1 - 8
6 ** Expander 6, 1 - 8 Expander 6, 1 - 8
7 ** Expander 7, 1 - 8 Expander 7, 1 - 8
8 ** Expander 8, 1 - 8 Expander 8, 1 - 8
!Network 2 can only be used on the Premier 168.
* Premier 88 and 168 only
** Premier 168 only
Outputs
The output module has 16 programmable outputs, which can
be used to drive auxiliary devices such as LED’s, sounders or
relays etc. Wire as per Panel Outputs shown on page 23 (see
page 60 for details). The electrical characteristics for the
outputs are shown below:
Bank Outputs Max Current Type
1 1 to 8 100mA Switched -ve
2 1 to 8 100mA Switched -ve
Tamper Output
The tamper switch on the output module is connected to the
tamper output at the top of the module. If monitoring of the lid
tamper is required, this output must be connected to a
suitable input on the control panel or zone expander.

Installation Premier 48, 88 & 168 Installation Manual
20 INS176
Zone and Output Numbering
Expander Zones Keypad Zones
Address Zones
Network 1
Zones
Network 2
Address Zones
Network 1
Zones
Network 2
1 9 - 16 73 - 80 1 Unmapped Unmapped
2 17 - 24 81 - 88 2 Unmapped Unmapped
3 25 - 32 89 - 96 3 Unmapped Unmapped
4 33 - 40 97 - 104 4 Unmapped Unmapped
5 * 41 - 48 105 - 112 5 * Unmapped Unmapped
6 * 49 - 56 113 - 120 6 * Unmapped Unmapped
7 * 57 - 64 121 - 128 7 * Unmapped Unmapped
8 * 65 - 72 129 - 136 8 * Unmapped Unmapped
Keypad Zones
Address Zones
Network 1
Zones
Network 2
Zones
Network 3
Zones
Network 4
Zones
Network 5
Zones
Network 6
Zones
Network 7
Zones
Network 8
1 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
2 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
3 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
4 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
5 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
6 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
7 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
8 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
Expander/OP16 Outputs
Address Outputs
Network 1
Outputs
Network 2
Outputs
Network 3
Outputs
Network 4
Outputs
Network 5
Outputs
Network 6
Outputs
Network 7
Outputs
Network 8
1 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8
2 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8
3 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8
4 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8
5 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8
6 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8
7 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8
8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8