Texecom Premier 412 Premier 816 Premier 832 User manual

INSTALLATION MANUAL
Security Control Panels with Integrated
Communicator
INS159-9
THANK YOU FOR VOTING TEXECOM

Contents Premier 412/816/832 Installation Manual
2 INS159
Contents
1. System Overview........................................ 4
System Architecture.........................................................4
Control Panels..................................................................4
Remote Keypads ..............................................................4
Zone Expansion Modules ................................................5
PC-Com Module ............................................................... 5
ComIP Module.................................................................. 5
Speech Module ................................................................5
Radio Receiver Module....................................................5
2. Installation .................................................. 6
Installation Sequence ......................................................6
Control Panel.................................................................... 6
Mounting ...................................................................................... 6
Wiring the Control Panel.............................................................. 6
Control Panel PCB Layout ...............................................7
Connecting Devices to the Data Bus .............................. 8
Wiring the Data Bus ..................................................................... 8
Cable Distances ........................................................................... 8
Overcoming Voltage Drop ........................................................... 9
Installing a Power Supply ............................................................ 9
Installing Remote Keypads............................................ 10
Keypad Layouts ......................................................................... 10
Remote Keypad Connections.................................................... 10
Remote Keypad Address........................................................... 10
Keypad Zones............................................................................ 10
Keypad Output........................................................................... 10
Keypad Speaker Output (LCDL/LCDLP Only)........................... 11
Adjustable Backlighting ............................................................. 11
Keypad Lid Tamper.................................................................... 11
Remote Zone Expander Module .................................... 11
Remote Expander Layout .......................................................... 11
Wiring the Zone Expander ......................................................... 11
Remote Expander Address........................................................ 11
Remote Expander Zones ........................................................... 11
Zone Expander Outputs............................................................. 12
Zone Expander Speaker Driver ................................................. 12
Local Zone Expander Module........................................ 12
Local Expander Layout .............................................................. 12
Local Expander Zones ............................................................... 12
Installing the Local Zone Expander ........................................... 12
Zone Connections .......................................................... 13
Normally Closed......................................................................... 13
Normally Open ........................................................................... 13
Single EOL - N/C & N/O (Burglary)............................................ 14
Single EOL - N/O (Fire).............................................................. 14
Single EOL - N/C........................................................................ 15
Single EOL - O/C Tamper .......................................................... 15
Single EOL – S/C Tamper.......................................................... 15
Double EOL................................................................................ 15
Zone Doubling ........................................................................... 15
Double Pole................................................................................ 16
2-Wire Smoke Detector .................................................. 17
Speaker/Bell Connections ............................................. 17
Speaker Operation..................................................................... 17
Siren/Bell Operation................................................................... 17
Siren/Spk Supervision ............................................................... 17
Telephone Line Connections......................................... 17
Panel Outputs 1 - 8......................................................... 18
Output Wiring ............................................................................. 18
Output Supervision .................................................................... 18
3. Commissioning & Troubleshooting ........ 19
Commissioning .............................................................. 19
Troubleshooting ............................................................. 19
4. Programming the Control Panel.............. 22
Introduction .................................................................... 22
Factory Defaults ......................................................................... 22
Viewing Numeric Data (LED Keypads).......................................22
Programming Text (LCD Only) ...................................................22
Program Menus ..............................................................23
Programming Zones .......................................................24
All Zone Options !" ...................................25
Zone Type !! ...................................25
Zone Wiring !# ...................................26
Zone Attributes 1 !$ ...................................26
Zone Attributes 2 !% ...................................27
Zone Attributes 3 !& ...................................27
Zone Attributes 3 (Key Switch) !& ...................................28
Zone Partitions & Groups !' ...................................28
Zone Text (LCD Only) !( ...................................28
Assign Radio Device !) ...................................28
Programming Partitions .................................................29
Partition Exit Delay #" ...................................30
Partition Entry Delay 1 #! ...................................30
Partition Entry Delay 2 ## ...................................30
Partition Communication Delay #$ ...................................30
Partition Bell Delay #% ...................................30
Partition Bell Duration #& ...................................30
Partition Options #' ...................................30
Partition Auto Arm/Disarm Options #( ............................31
Equipment Areas #) ...................................31
Programming Global Options ........................................32
System Timers $" ...................................34
System Counter/Levels $! ...................................34
System Control Timers $# ...................................35
System Options 1 $$ ...................................35
System Options 2 $% ...................................35
System Options 3 $& ...................................35
Hardware Options $' ...................................36
Auxiliary Input Options $( ...................................36
Miscellaneous Options 1 $) ...................................37
Miscellaneous Options 2 $* ...................................37
Programming Remote Keypads.....................................39
Keypad Options 1 %" ...................................40
Keypad Options 2 %! ...................................40
Keypad Options 3 %# ...................................40
Keypad Options 4 %$ ...................................41
Programming Remote Expanders..................................42
Expander Partitions &" ...................................43
Expander Tones &! ...................................43
Expander Volume Level &# ...................................43
Programming System Outputs.......................................44
Panel Outputs '" ...................................46
Fast Format/Speech Channels '! ...................................46
Expander 1 Outputs '# ...................................46
Expander 2 Outputs '$ ...................................46
Expander 3 Outputs '% ...................................46
Keypad Outputs '& ...................................46
Output Groups and Types..............................................46
Output Attributes.........................................................................48
Programming the Communicator ..................................49
Communicator Options (" ............................51
ARC 1 Communicator Menu (! ............................51
Telephone Numbers (!-".....................52
Account Numbers (!-!.....................52
Protocol Type (!-#.....................52
Dial Attempts (!-$.....................52
Partition Options (!-%.....................53
Reporting Options (!-&.....................53
Pulse Format Options (!-'.....................53
Fast Format Reporting Channels (!-(.....................54
Protocol Options (!-).....................54
ARC 2 Communicator Options (# ............................55
Fast Format Restore Channels ($ ............................55
Fast Format Open/Close Channels (% ............................55
Cancel Call Waiting Sequence (& ............................55
Programming Check List............................................................56
Programming Download Options ..................................57
Download Menu (' ............................58
Download Options ('-".....................58
Call Back Number ('-!.....................59

Premier 412/816/832 Installation Manual Contents
INS159 3
UDL Passcode ('-#....................59
Download Dial Attempts ('-$....................59
Ring Count ('-%....................59
Com1 Device Type ('-&....................59
ComIP Address & Port ('-'....................59
ComIP Gateway Address ('-(....................59
ComIP Subnet Mask ('-)....................59
Programming Reporting Codes.....................................60
Zone Alarm/Restore Codes ((............................61
Zone Bypass/Unbypass Codes ()............................61
Non Zone Alarm/Restore Codes (*............................61
Contact ID and SIA Codes .........................................................61
Programming Users .......................................................62
Program User )"............................64
User Options 1 )!............................64
User Options 2 )#............................64
User Options 3 )$............................65
User Text (LCD Only) )%............................65
Program Standard Users )&............................65
Default ALL Users )'............................65
System Tests & Utilities .................................................66
Walk Test *"............................67
Test Speakers & Outputs *!............................67
Send Test Call *#............................67
Enable Remote/Engineer Access *$............................67
Start Call Back *%............................67
Program Time *&............................67
Program Date *'............................67
Program Banner Text (LCD only) *(............................67
Print 100 Events *)............................67
Log Off Engineer **............................67
Using RadioPlus .............................................................68
5. Operating the Alarm System ................... 70
Introduction ....................................................................70
Arming & Disarming the Alarm System .........................70
Checking if the System is Ready to Arm....................................70
Away Arming...............................................................................70
Stay Arming ................................................................................70
Cancelling the Arming Process..................................................71
Disarming During Entry ..............................................................71
Disarming when not in Entry ......................................................71
Disarming after an Alarm............................................................71
Auto Stay Arming........................................................................71
Changing between Delayed and Instant Stay............................71
Arming and Disarming Partitions ..................................72
Away Arming Partitions...............................................................72
Stay Arming Partitions ................................................................72
Disarming Partitions ...................................................................72
Changing to another Partition ....................................................73
Bypassing Zones ............................................................73
Manually Bypassing Zones ........................................................73
Unbypassing Zones....................................................................73
Group Bypass.............................................................................73
Quick Bypass and Arm...............................................................74
Reset Alarms ..................................................................74
Last Alarm Log................................................................74
Service Faults .................................................................75
Anti-code Reset ..............................................................76
Toggle Chime On and Off ..............................................76
Change User Code .........................................................76
View Log (LCD Only) ......................................................76
Abort Communications ..................................................76
6. Specifications ........................................... 77
Control Panel and Remote Keypads .............................77
Remote and Local Zone Expander ................................78
Safety Notes ...................................................................78
European Standards.......................................................78
Warranty..........................................................................79
7. Quick Reference Guide ............................ 80
Notes...............................................................................84
System Overview
Installation
Control Panel PCB Layout
Installing Remote Keypads & Expanders
Zone Connections
Siren/Bell, Telephone and Panel Outputs
Commissioning & Troubleshooting
Programming Menus
Programming Zones
Programming Partitions
Programming Global Options
Programming Remote Keypads
Programming Remote Expanders
Programming System Outputs
Programming the Communicator
Programming Download Options
Programming Reporting Codes
Programming Users
System Tests, Utilities and Using RadioPlus
Operating the Alarm System
Specifications
Quick Reference Guide

System Overview Premier 412/816/832 Installation Manual
4 INS159
1. System Overview
System Architecture
Premier 412/816/832
Onboard
Communicator/
modem
EOL Zone Inputs
= 4Premier 412
Premier 816 = 8
Premier 832 = 8
Data Bus
6 Programmable
100mA Outputs
2 Programmable
1A Outputs
Siren Driver
Aux Input
6 Remote Keypads (max)
Alarm Receiving
Centre
Modem
PC and Modem for
Remote Upload/Download
PC-Com
PC and for
Local Upload/Download
PC-Com
Premier 8XE
Local Zone Expander
Premier Bell Module
OR
Premier RKP4/8/16
Remote Keypad
456
123
7890
Armed
Zones
87654321
Ready
Alarm
Service
ARM
STAY
DISARM
BY
PASS
MENU
AREA
Com1
2 EOL Zones
4 ghi
2 abc
3 def
7 pqrs
Area
5 jkl
8 tuv
0
6 mno
9 wxyz
1
Yes
Stay
Chime
Bypass Reset
Menu
No
Bypass Service
Power
Armed
Ready
Premier 832
12:55.22 21/11
1 Output
(100mA)
Premier LCD/LCDP
Remote Keypad
2 EOL Zones
4 ghi
2 abc
3 def
7 pqrs
Area
5 jkl
8 tuv
0
6 mno
9 wxyz
1
Yes
Stay
Chime
Bypass Reset
Menu
No
Bypass Service
Power
Armed
Ready
Premier 832
12:55.22 21/11
1 Output
(100mA)
Premier LCDL/LCDLP
Remote Keypad
Speaker Driver
Premier RKP8/16 Plus
Remote Keypad
4 ghi
2 abc
3 def
7 pqrs
Area
5 jkl
8 tuv
0
6 mno
9 wxyz
1
Yes
Stay
Chime
Bypass Reset
Menu
No
Alarm Armed
Service Ready
Stay
Fire
12345678
910 11 12 13 14 15 16
Bypass Instant
2 EOL Zones ( )RKP16 Plus
8 EOL Zone Inputs
Premier 8X Remote
Zone Expander
2 Programmable
100mA Outputs
Speaker Driver
Remote Expanders
Premier 412
Premier 832
= 1
= 3
Premier 816 = 1
Control Panels
The Premier 412, 816 and Premier 832 are highly
sophisticated security control panels with Integrated Multi-
protocol Digital Communicator/Modem. The control panels
have the following features:
Features 412 816 832
Zones 4 8 8
Max. Zones when expanded 12 16 32
Partitions 2 4 4
User Codes 32 32 64
Event Log 750 750 1000
Touch Tone Remote Control - - !
Programmable Aux. Input !!!
Supervised Siren/Bell Output !!!
2 x 1A Supervised Outputs !!!
6 x 100mA Outputs !!!
Printer/UDL Port !!!
Integrated Modem/Communicator !!!
Remote Keypads
The control panels will accept up to a maximum of 6 remote
keypads. All remote keypads require a 4-wire connection to
the data network and have a built in piezoelectric sounder.
The following remote keypad models are available:
Premier RKP4/8/16
A cost effective range of remote keypads with either 4, 8 or
16 zone indicator lights.
•4-wire connection to data network.
•Built in piezoelectric sounder.
•Dual level back-lighting, normally dim, switching to
bright for 8 seconds after any key press
•Dedicated status lights for “Alarm”, “Service”, “Armed”
and “Ready”.
Premier RKP8/16 Plus
A professional range of LED remote keypads with either 8 or
16 zone indicator lights.
•2 programmable EOL zones.
•4-wire connection to data network.
•Built in piezoelectric sounder.

Premier 412/816/832 Installation Manual System Overview
INS159 5
•Fully adjustable back-lighting, normally bright, dim or
off, changing to bright whenever a keypad is used and
during the entry mode
•Dedicated status lights for “Alarm”, “Service”, “Armed”,
“Ready”, “Fire”, “Bypass”, “Instant” and “Stay”
Premier LCD/L
The Premier LCD remote keypad has a standard 32
character back-lit LCD display, whereas the Premier LCDL
has a large 32 character back-lit LCD display.
•2 programmable EOL zones
•1 programmable low current (100mA) output
•4-wire connection to data network.
•Built in piezoelectric sounder.
•Fully adjustable back-lighting, normally bright, dim or
off, changing to bright whenever a keypad is used and
during the entry mode
•Dedicated status lights for “Power”, “Armed”, “Ready”,
“Service” and “Bypass”
•Speaker driver output (Premier LCDL Only).
Premier LCDLP
•Premier LCDL keypad with built-in proximity tag reader
Premier LCDP
•Premier LCD keypad with built-in proximity tag reader
Zone Expansion Modules
Either system can be expanded using one of the following
zone expansion modules:
Premier 8X Remote Zone Expander
This module comes supplied in its own enclosure and is
connected to the control panel data network to provide
remote expansion of the system. This module provides the
following additional facilities:
•8 programmable EOL zones
•2 programmable low current (100mA) outputs
•Speaker driver output with electronic volume control.
Premier 8XE Local Zone Expander
This module comes supplied as a PCB and simply plugs
onto the main control panel circuit board. This module
provides 8 programmable EOL zones.
PC-Com Module
This module plugs on to the Premier 412,816 and Premier
832 control panel to provide an RS232 interface, which can
be used for:
•Connection of a serial printer to print the event log
•Upload/download the system programming via Wintex
UDL software and PC.
ComIP Module
This module plugs on to Com1 of the control panel to
provide the following:
•Alarm event reporting via TCP/IP (WAN/LAN).
•High speed upload/download of system programming
via WAN/LAN using Wintex UDL software.
Speech Module
This module plugs on to the control panel to provide the
following:
•2 recordable messages (12 seconds each).
•Each message can be assigned to a specific output
function, e.g. Alarm or Fire.
This manual does not cover the full installation of this device;
please refer to the instructions supplied with the Speech
Module.
Radio Receiver Module
The control panel will accept either the Texecom RadioPlus
receiver module and radio devices or the Inovonics EE4000
radio receiver and ES1200 series devices. The receiver
module plugs on to Com1 of the control panel to provide the
following:
•32 wireless devices, such as PIR, Door Contacts,
Remote FOBs etc.
•RF supervision of each device.
•Battery supervision of each device.
This manual does not cover the full installation of these
devices; please refer to the instructions supplied with the
radio receiver module.

Installation Premier 412/816/832 Installation Manual
6 INS159
2. Installation
Installation Sequence
Before attempting to install the alarm system, read this
section. Once you have an overall understanding of the
installation sequence, carefully work through each step.
1: Design the Layout
Make a rough sketch of the premises to get an idea of where
all alarm detection devices, keypads and other modules are
to be located.
2: Mounting the Panel
The control panel should be mounted in a dry area close to
an unswitched AC power source and the incoming
telephone line.
!You must complete all wiring before connecting the
battery, or applying AC to the panel.
!Some versions of the control panel are not supplied
with an integral mains transformer. If this is the case a
suitable external mains transformer will be required
(see page 77)
3: Install the Keypads
Mount and connect the keypads to the control panel.
4: Zone Wiring
Install detection devices and connect to control panel.
5: Other Wiring
Complete all other wiring including bells or sirens and
telephone line connections.
6: Apply Power to the Control Panel
Once steps 1 to 5 are completed, apply power to the control
panel. First, connect the red battery lead to the positive
terminal and the black lead to negative. Then, connect the
AC.
7: Complete the Installation Records & Defaults Booklet
Supplied with the control panel is the “Installation Records
and Defaults” booklet. This booklet allows you to record all
programming data and also lists all program defaults. It is
recommended that the booklet is filled in before attempting
to program the system.
8: Program the System
Using the Programming Worksheets program the control
panel in accordance with the procedures in Section 3.
9: Testing the System
Test the system thoroughly to ensure that all features and
functions are operating as required.
Control Panel
Mounting
Mount the control panel on a flat, plumb wall using at least
three appropriate screws. The rear casing has been
designed with a central key-hole slot so that mounting is
possible without removing the Printed Circuit Board (PCB).
The angled slot in the lower corner has been provided to
allow the panel to be levelled easily. If the PCB has to be
removed, carefully pull back the two front PCB securing
clips, lift the front of the PCB and slide it downward. To
replace the PCB simply reverse the above procedure.
!It is essential to ensure that none of the fixing slots or
cable entries are accessible after fixing.
Mains cabling must be secured (e.g. with a cable tie)
to one of the anchor points provided.
Wiring the Control Panel
WARNING: ELECTRICITY CAN KILL
BEFORE connecting the control panel
ALWAYS disconnect the supply at the consumer unit.
If in ANY doubt consult a qualified electrician.
ONLY connect the mains supply to the mains
terminal block, NEVER connect the mains supply
directly to the PCB.
The system installation MUST be carried out in
accordance with the national safety standards, for
example EN 60950: 1992.
ALWAYS refer to National Wiring Regulations when
conducting installation.
An appropriate and readily accessible
disconnection device (e.g. an unswitched fused
spur) MUST be provided as part of the installation.
The disconnection device must NOT be fitted in a
flexible cord.
Where identification of the neutral in the mains
supply is NOT possible, a two-pole disconnection
device MUST be used.
The building mains supply MUST incorporate
appropriate short-circuit backup protection (e.g. a
fuse or circuit breaker) of High Breaking Capacity
(HBC, at least 1500A).
Use mains cable of adequate carrying capacity for
the rated current (i.e. at least 0.75mm2).
"

Premier 412/816/832 Installation Manual Installation
INS159 7
Control Panel PCB Layout
Com 1
2-Wire
Smoke Det.
Enable
Load
Defaults
Box
Tamper
Panel
Outputs
1
Siren
2
Strb
Input
Aux
34 5678
A.C. Z1 Z3
COM
COM
Z2 Z4
+Batt- +
+
+
TR
Siren/Spk
-
-
-
Aux12
Data
TRT1R1
2 3 54 6 7 10
9
8
11
12
1516 1317
19
20
Z5 Z7
COM
COM
Z6 Z8
Tamper
Disable
1
Batt
14
1
Kick Start
Eng Keypad
Tx Rx
21
24
F4 Fault
Network
F3 Fault
Siren
F2 Fault
Aux
F2F3F4
F1
2318 22
SK1
1: Earth Ground Connection
Earth ground. Connect to earth or an earth rod.
Failure to fit an earth cable may prevent proper
operation of the system and will invalidate the
Texecom warranty and product approvals.
2: AC Input
Connect to a 16.5V transformer.
Do NOT connect the mains supply to the AC
input terminals.
3: Battery Connections
A 12V rechargeable battery must be connected to these two
terminals in order to provide continuous system operation in
the event of mains failure. The battery output is protected by
fuse F1 (1.6 Amp).
4: Data Bus Connections
The data bus terminals provide connections to the remote
keypads and Premier 8X Remote Zone Expander. The + and
– terminals provide power whilst the T and R terminals are
transmit and receive data.
5: Siren/Spk output
These terminals are used for driving speakers, sirens or
bells. The output can be programmed for speaker driver or
for Siren/bell driver (see page 35). This output is supervised,
if no warning devices are fitted, either fit a 1KΩresistor
between these two terminals or disable the siren
supervision, see page 36.
6: Auxiliary 12V Power
These terminals provide auxiliary power for devices that
require 12V power. The auxiliary output is protected by fuse
F2 (1 Amp).
7: Zone Inputs 1 to 8
These terminals provide the connections to the zone inputs.
The Premier 816 and Premier 832 have 8 zone inputs,
whereas the Premier 412 has only 4 zone inputs. There are
several ways to wire a zone (see page 12). Each zone is fully
programmable, see page 24 for information on
programming zones.
8: Two-Wire Smoke Detector Enable
Set this link as shown when connecting 2-wire smoke
detectors to Panel Output 1.
Output 1 is enabled for 2-wire smoke detectors
Output 1 is normal
9: Aux Input
This is a programmable input, it can be used for monitoring
auxiliary tamper devices etc, see page 36 for programming
details.
10: Panel Outputs 1 to 8
These are programmable outputs. Panel outputs 1 and 2 are
high current (1 Amp) supervised outputs. If panel outputs 1
or 2 are not used, either fit a 1KΩresistor between the
unused output and Auxiliary 12V + or disable the output
supervision, see page 36. Panel outputs 3 to 8 are low
current (100mA) outputs.
"#
"#

Installation Premier 412/816/832 Installation Manual
8 INS159
11: Communication Port
The serial communication port is used for connecting to a
printer or PC for local downloading.
12: Load Defaults
Short between the centre and either of the outer pins during
power up to restore the control panel default program
parameters. These pins can also be used to reset the
Engineer code back to its default value, see page 67.
!Do not leave these pins shorted, otherwise the control
panel event log will be erased.
13: Box Tamper Disable
Fit link as shown:
Box Tamper Disabled
Box Tamper Enabled
14: Local Zone Expander
The Premier 8XE Local Zone Expander can be plugged on to
the main PCB. The local expander provides an additional 8
programmable zones (see page 12).
15: Speech Module
A two channel Speech Module can be plugged on to the
main PCB (SK1). This connector is only fitted on the Premier
816Plus and Premier 832 control panels.
16: Box Tamper Switch
Box tamper protection for the main control panel.
17: Power Light
On steady when either AC or standby battery is present.
Flashes when the on-board communicator is dialling or
sending data.
18: Electronic Fuses
The PCB is protected using electronic PTC fuses:
•F1 (1.6 Amp) Battery fuse
•F2 (1 Amp) Auxiliary 12V power fuse
•F3 (1 Amp) Siren/Bell output fuse
•F4 (1 Amp) Network fuse
19: Telephone Line Connections
Telephone line connections (see page 17).
20: RJ11 Telephone Line Connector
An RJ11 connector is provided so that the panel can be
connected to the telephone line via a standard RJ11 patch
lead.
21: Engineers Keypad Connection
An engineers keypad (Premier LCD keypad and interface
lead) can be temporarily plugged onto this connector to
allow system programming and testing.
22: Network Data Indicator LEDs
The red transmit (Tx) LED indicates that data is flowing out
of the control panel and normally flashes very quickly. The
green receive (Rx) LED indicates that data is flowing into the
control panel. The green LED flashes faster as more devices
are connected to the data network.
23: Electronic Fuse Fault Indicator LEDs
Electronic fuses F2-F4 have red indicator LEDs, which light
up when the relevant fuse is open circuit (fault).
24: Battery Kick Start Pins
The control panel has a deep discharge protection circuit
that prevents the standby battery from being fully
discharged. When powering up the control panel without AC
Mains (battery only), the centre and either outer pins must
be shorted together in order to bring the battery into circuit.
Connecting Devices to the Data Bus
Before connecting remote keypads and zone expanders,
isolate ALL power from the control panel (AC Mains &
Battery). Do not continue if there is still power present on the
control panel.
!Connecting devices with power still present on the
control panel may damage the device or control panel
and invalidate any warranty.
Remote keypads and zone expanders are all connected to
the same data terminals located at the bottom left hand
corner of the control panel and may be connected serially
(daisy chain), in parallel (star) or any combination of the two.
Wiring the Data Bus
The data bus is made up of four terminals incorporating
power and data. To ensure correct operation, all four
terminals on the device must be connected to the
corresponding terminals on the control panel, or previous
device (see page 9 for wiring details). The table below
shows each terminal and its description:
Terminal Description
+ +12V Supply
- 0V Supply
T Transmit Data
R Receive Data
Cable Distances
The maximum recommended distance for devices when
using standard 7/0.2 alarm cable is:
•250m for each branch when using the star (parallel)
configuration
•When using a daisy chain (series) configuration the
maximum distance will depend on the number of
devices connected on the chain. The more devices that
are connected, the shorter the distance to the last
device (this is due to voltage drop in the cable)
Whichever method of wiring configuration is used, ensure
that the voltage between the ‘+’ and ‘–’ terminals at each
device is no lower than 10.0V when the system is running on
the standby battery.

Premier 412/816/832 Installation Manual Installation
INS159 9
The table below shows maximum cable runs when one
keypad or expander is installed using standard 7/0.2 alarm
cable with various loads:
Configuration Max. Cable Run
1. Keypad + 2 PIR’s @15mA 250m
2. Expander + 2 PIR’s @15mA 250m
3. Expander + 8 PIR’s @15mA 100m
4. As No. 3 + 16ΩSpeaker 30m
Overcoming Voltage Drop
There are several ways to overcome voltage drop:
•Use thicker lower resistance cable. Standard 7/0.2
alarm cable has a resistance of 8Ωper 100m
•Double up on the power connections – this will require
using a 6 or 8-core cable rather than a 4-core cable
•Install a power supply to power the device locally,
remember to common the two negative connections
Installing a Power Supply
When a power supply is installed, the 0V connections on the
power supply must be connected through to 0V on the
control panel and the +12V connection between the control
panel and the device must be disconnected (see figure
below).
Control Panel
+
TR
Remote Keypad
-
Data
Data Bus
+
TR
-
+
TR
Remote Keypad
-
Data
+
TR
Remote Keypad
-
Data
Remote Expander
+
TR
-
Data To additional
devices
250 metres
Control Panel
Data Bus
+
TR
-
+
TR
Remote Keypad
-
Data
+
TR
Remote Keypad
-
Data
+
TR
Remote Keypad
-
Data
12V Power Supply
+-
To additional
devices
1 Kilometre
Disconnect +12V
from control panel
250 metres
Data Bus Connections (250m without additional power supply).
Data Bus Connections (1Km with additional power supply).

Installation Premier 412/816/832 Installation Manual
10 INS159
Installing Remote Keypads
Keypad Layouts
TR
+
-
Premier RKP8/16 Plus Layout
Z1
COM
Z2
1
2
3
5
4
456
123
790
DISARM
BY
PASS
MENU
+
TR
-
8AREA
1
ARM
STAY
24
3
Premier RKP4/8/16 Layout
Zone 1
TA
Zone 2
T
A
NETWORK
+
TR
-
O/P-
Premier LCD/LCDL/LCDP/LCDLP Layout
1
2
3
5
4
6
SPK-
7
2431
ON
2431
ON
$Address DIL Switch
%Tamper Switch
&Piezo Sounder
'Data Bus Connections
(Programmable Zones 1 and 2
)Speaker Output (Premier LCDL/LCDLP Only)
*Programmable Output
Remote Keypad Connections
The remote keypad is connected to the data bus terminals
located at the bottom left hand side of the PCB. (See pages
7 to 9).
Remote Keypad Address
Each remote keypad must be assigned a different address
using the Address DIL switch ($). The table below shows
how to set the address:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On/Off Off Off Off
2431
ON
2 Off On Off Off
2431
ON
3 Off Off On Off
2431
ON
4 Off Off Off On
2431
ON
5 On Off Off On
2431
ON
6 Off On Off On
2431
ON
Keypad Zones
The Premier RKP8/16 Plus and all LCD remote keypads have
two programmable zone inputs (see page 13 for wiring
details). Each zone is also fully programmable (see page 24
for programming details). The table below shows the zone
allocation when using the Premier RKP8/16 Plus or Premier
LCD remote keypads:
Premier 412 Premier 816/832
Address
Zone 1 Zone 2 Zone 1 Zone 2
1 Zone 05 Zone 06 Zone 09 Zone 10
2 Zone 07 Zone 08 Zone 11 Zone 12
3 Zone 09 Zone 10 Zone 13 Zone 14
4 Zone 11 Zone 12 Zone 15 Zone 16
5 N/A N/A N/A N/A
6 N/A N/A N/A N/A
!The onboard remote keypad zones are not seen by
the system until they have been enabled. To enable
the onboard keypad zones (see page 41 for details).
Keypad Output
All Premier LCD remote keypads have one programmable
output, which can be used to drive auxiliary devices such as
LED’s, sounders or relays etc. Wire as per Panel Outputs
shown on page 18 (see page 46 for programming details).

Premier 412/816/832 Installation Manual Installation
INS159 11
Keypad Speaker Output (LCDL/LCDLP Only)
The Premier LCDL and LCDLP keypads has an output that
can be used for driving up to one 8Ωor two 16Ω
loudspeakers (see page 17 for wiring details).
!The speaker volume is also fully adjustable (see page
34 for details).
Adjustable Backlighting
To adjust the keypad backlighting press the YES key, then
with the YES key still pressed use +to increase or
decrease the backlighting until the required brightness is
achieved, then release both keys.
!The backlight can only be adjusted when the keypad
is not in a menu.
Keypad Lid Tamper
The lid tamper of each keypad can be disabled if required
using the relevant keypad option in the Keypad Options 4
menu (see page 41 for details).
Remote Zone Expander Module
The Premier 8X Remote Zone Expander provides 8 additional
detection zones, two programmable outputs and a speaker
driver output.
Remote Expander Layout
+-
TR
62
-
+
Z2
COM
Z1
1
Z4
COM
Z3
-
+
Z6
COM
Z5
Z8
COM
Z7
+-
OP1
SPK OP2
Tamp Disable
2431
1234
2
4
53 3
78
9
+
$Data Bus Connections
%Auxiliary 12V
&Programmable Zone Inputs
'Programmable Outputs 1 and 2
(Speaker Driver Output
)Power LED
*Disable Tamper Jumper
+Tamper Switch
,Address DIL Switch
Wiring the Zone Expander
The Remote Zone Expansion Module is connected to the
data bus terminals located at the bottom left hand side of
the PCB. (See pages 7 to 9).
Remote Expander Address
Each remote expander must be assigned a different address
using the Address DIL switch (,). The table below shows
how to set the address:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On/Off Off Off Off
2431
ON
2 Off On Off Off
2431
ON
3 Off Off On Off
2431
ON
!Only one remote expander can be connected to the
Premier 412 &816 control panels (Address = 1).
Remote Expander Zones
The Premier 8X Remote Expander has eight programmable
zone inputs (see page 13 for wiring details). Each zone is
also fully programmable (see page 24 for programming
details).
The table below shows the system zone allocation when one
or more modules are installed:
Remote Expander Zone Inputs
Address
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8
1 09 10 11 12 13 14 15 16
2 17 18 19 20 21 22 23 24
3 25 26 27 28 29 30 31 32
!When the system is expanded above 8 zones, it
MUST be fitted with a suitable remote keypad. For
systems up to 16 zones a Premier RKP16 or Premier
RKP16 Plus should be installed. For systems above 16
zones a LCD remote keypad should be installed.
The system will only support one type of expansion
device for zones 09 - 16, i.e., you can fit either a
Premier 8X Remote Expander (Address = 1) or a
Premier 8XE Local Expander, you cannot fit both.

Installation Premier 412/816/832 Installation Manual
12 INS159
Zone Expander Outputs
The Zone Expander module has two programmable outputs,
which can be used to drive auxiliary devices such as relays,
LED’s, smoke detectors etc. The table below shows the
electrical characteristics for each output:
No Supervised Max Current Type
1 No 100mA Switched –ve
2 No 100mA Switched –ve
Wire as per Panel Outputs shown on page 18.
Zone Expander Speaker Driver
The Zone Expander has a Speaker driver output and can be
used for driving 8 or 16 Ohm loud speakers as shown on
page 17.
Local Zone Expander Module
The Premier 8XE Local Zone Expander plugs onto the
control panel to provide 8 additional programmable
detection zones.
Local Expander Layout
Z9 Z11
COM
COM
Z10 Z12
+-
Aux12
3
2
Z13 Z15
COM
COM
Z14 Z16
1
$Zone Inputs 9 to 16
These terminals provide the connections to the zone inputs.
%Auxiliary 12V Power
These terminals provide auxiliary power for devices that
require 12V power. The auxiliary output is protected by fuse
F2 (1 Amp) on the control panel.
&Plug-On Connector
The Premier 8XE Local Zone Expander plugs onto the
control panel via this connector and is held in place by four
plastic pillars located in each corner.
Local Expander Zones
The Premier 8XE Local Zone Expander has eight
programmable zone inputs (see page 13 for wiring details).
Each zone is also fully programmable (see page 24 for
programming details).
The table below shows the zone allocation when the module
is installed:
Panel Panel Zones Expander Zones
Premier 412 1 to 4 9 to 16
Premier 816 1 to 8 9 to 16
Premier 832 1 to 8 9 to 16
!When the system is expanded above 8 zones, it
MUST be fitted with a suitable remote keypad. For
systems up to 16 zones a Premier RKP16 or Premier
RKP16 Plus should be installed. For systems above 16
zones a Premier LCD/LCDL should be installed.
The system will only support one type of expansion
device for zones 09 - 16, i.e., you can fit either a
Premier 8X Remote Expander (Address = 1) or a
Premier 8XE Local Expander, you cannot fit both.
Installing the Local Zone Expander
"To install the Local Zone Expander proceed as follows:
1. Ensure that all power is removed from the control panel
(mains and battery) before attempting to fit the
expander.
2. Push the four support pillars (supplied) into the four
locating holes on the control panel PCB.
3. Align the Local Expander Connector with the 8 way plug
(JP2) on the control panel. Push expander into place,
ensuring that all four pillars clip into the four locating
holes on the local expander.

Premier 412/816/832 Installation Manual Installation
INS159 13
Zone Connections
Each zone on the system is fully programmable to allow for
maximum flexibility (see page 24 for Zone Programming
details). The program options for a zone will also determine
how the zone may be wired. The following wiring options are
available:
Type Zone Status Response
Shorted Secure
-Normally Closed > 20K Active
Shorted Active
$Normally Open > 20K Secure
0 - 1K Active
1.1K - 4.7K Secure
%Single EOL - N/C
& N/O (Burglary)
> 4.8K Active
0 - 1K Active
1.1K - 4.7K Secure
&Single EOL - N/O
(Fire)
> 4.8K Trouble
0 - 1K Trouble
1.1K - 4.7K Secure
'Single EOL - N/C
> 4.8K Active
0 - 1K Secure
1.1K - 4.7K Active
(Single EOL - O/C
Tamper
> 4.8K Tamper
0 - 1K Tamper
1.1K - 4.7K Secure
)Single EOL - S/C
Tamper
> 4.8K Active
0 - 1K* Tamper
1.1K - 4.4K Secure
4.5K - 20K Active
*Double EOL
> 20K Tamper
Shorted Zones A & B Trouble
1.0K - 2.2K Zones A & B Secure
4.8K - 6.0K Zone A Violated
2.3K - 4.7K Zone B Violated
+Zone Doubled
Open Zones A & B Violated
0 - 1K Tamper
1.1K - 4.0K Secure
4.1K - 5.6K Trouble (Fault)
5.7K - 8.0K Active
8.1K - 20K Trouble (Masked)
,Triple EOL
> 20K Tamper
* This value may vary depending on the country variant.
Normally Closed
Use this wiring configuration when connecting normally
closed detection devices to the zone. Ensure that the zone
is programmed for Normally Closed operation (see page
26). The zone must be wired as follows:
2 Normally
Closed Contacts
1 Normally
Closed Contact
Premier LCD/LCDL
Keypads
Zx Com Zx Com
AT
Zone x
Control Panel &
Expanders
AT
Zone x
Normally Open
Use this wiring configuration when connecting normally
open detection devices to the zone. Ensure that the zone is
programmed for Normally Open operation (see page 26).
The zone must be wired as follows:
2 Normally
Open Contacts
1 Normally
Open Contact
Zx Com Zx Com
Premier LCD/LCDL
Keypads
AT
Zone x
Control Panel &
Expanders
AT
Zone x

Installation Premier 412/816/832 Installation Manual
14 INS159
Single EOL - N/C & N/O (Burglary)
Use this wiring configuration when connecting a mixture of
normally closed and normally open detection devices to the
zone. Ensure that the zone is programmed for Single EOL -
N/C & N/O operation (see page 26). The zone must be wired
as follows:
Normally
Open Contact
Zx Com Zx Com
Normally
Closed Contact
E.O.L
3.3 K
E.O.L
3.3 K
2 Normally
Open and 2 Normally
Closed Contacts
Zx Com Zx Com
1 Normally
Closed and 1
Normally Open
Contact
E.O.L
3.3 K
E.O.L
3.3 K
Premier LCD/LCDL
Keypads
Control Panel &
Expanders
AT
Zone x
AT
Zone x
Premier LCD/LCDL
Keypads
Control Panel &
Expanders
AT
Zone x
AT
Zone x
Single EOL - N/O (Fire)
Use this wiring configuration when connecting a 4-wire
smoke detector to the zone. Ensure that the zone is
programmed for Single EOL - N/O (Fire) operation (see
page 26). The zone must be wired as follows:
Program as
Sensor Reset
O/P1or2 Zx
Power Supervision Relay
e.g ESL #204A or equivalent
4-Wire
Smoke
Detector
4-Wire
Smoke
Detector
Com Aux 12V +
E.O.L
3.3 K
In In
Out Out
Alarm
(+)
(+)
(-)
(-)
In In
Out Out
Alarm
(+)
(+)
(-)
(-)
Premier LCD/LCDL
Keypads
Control Panel &
Expanders
AT
Zone x

Premier 412/816/832 Installation Manual Installation
INS159 15
Single EOL - N/C
Use this wiring configuration when connecting just normally
closed detection devices to the zone. Ensure that the zone
is programmed for Single EOL - N/C operation (see page
26). The zone must be wired as follows:
Zx Com
Normally
Closed Contact
E.O.L
3.3 K
2 Normally
Closed Contacts
Zx Com
E.O.L
3.3 K
Premier LCD/LCDL
Keypads
Control Panel &
Expanders
AT
Zone x
AT
Zone x
Single EOL - O/C Tamper
Use this wiring configuration when connecting just normally
closed detection devices to a zone and when a tamper
response is required in the event of an open circuit. Ensure
that the zone is programmed for Single EOL - O/C Tamper
operation (see page 26). The zone must be wired as follows:
2 Normally
Closed Contacts
Zx Com Zx Com
Normally
Closed Contact
E.O.L
3.3 K
E.O.L
3.3 K
Premier LCD/LCDL
Keypads
Control Panel &
Expanders
AT
Zone x
AT
Zone x
Single EOL – S/C Tamper
Use this wiring configuration when connecting just normally
closed detection devices to the zone and when a tamper
response is required in the event of a short circuit. Ensure
that the zone is programmed for Single EOL - S/C Tamper
operation (see page 26). Wire Single EOL - S/C Tamper
zones as shown for Single EOL - N/C.
Double EOL
Use this wiring configuration when connecting detection
devices to a zone that requires alarm/tamper monitoring.
Ensure that the zone is programmed for Double EOL
operation (see page 26). The zone must be wired as follows:
Zx Com Zx Com
1 Detection Device
2 Detection Devices
Alarm Alarm Tamper Tamper
E.O.L
3.3 K
E.O.L
3.3 K
3.3 K
3.3 K
Alarm
3.3 K
Tamper
Premier LCD/LCDL
Keypads
Control Panel &
Expanders
AT
Zone x
AT
Zone x
Zone Doubling
This wiring option allows you to wire two detection devices
into one set of zone connections. However, the system will
treat each device, as if it were connected to a separate zone,
i.e., each device is fully programmable.
!When using this configuration, the system must be
fitted with the appropriate keypad, Premier RKP16 on
the Premier 816 and the Premier RKP8 on the Premier
412.
When a zone is configured for “Zone Doubled” it must be
wired as follows:
Any Z
Terminal (Panel)
Zx
Any Com
Terminal
Com
Normally Closed Contact
Zone A
4.7 K
3.3 K
Zone B
Normally Closed Contact

Installation Premier 412/816/832 Installation Manual
16 INS159
The following table shows how each physical zone is
mapped when using the “Zone Doubled” configuration:
Premier 412
Panel Zone Zone A Zone B
1 1 5
2 2 6
3 3 7
4 4 8
Premier 816/832
Panel Zone Zone A Zone B
1 1 9
2 2 10
3 3 11
4 4 12
5 5 13
6 6 14
7 7 15
8 8 16
!Zones above 9 on either the Premier 8X/8XE Expander
MUST not be configured for “Zone Doubled”.
The Premier 8X/8XE Expander cannot be used on the
Premier 816/832 control panels if any of zones 1 - 8
are configured as “Zone Doubled”.
Triple EOL
This wiring option is designed to be used with Texecom
detectors that support Triple EOL (T-EOL) wiring. Ensure
that the zone is programmed for Triple EOL operation (see
page 26). The zone must be wired as follows:
Control Panel/Expander
Aux 12
+ -
Zx
COM
Zy
Prestige AM
T-EOL Detector
0V 12V T-EOL RLED
Spare
SETTEST
Optional Optional
Selectable EOL Values
2k2 4k7 2k2
LCD Keypad
Network
+ -
AZone x T
Prestige AM
T-EOL Detector
0V 12V T-EOL RLED
Spare
SETTEST
Optional Optional
Selectable EOL Values
2k2 4k7 2k2
TR
Zx Com
Fault
E.O.L
2.2 K
2.2 K
Alarm
4.7 K
Tamper
Premier LCD/LCDL
Keypads
Control Panel &
Expanders
AT
Zone x
!Triple EOL wiring can only be used on remote
keypads and remote expanders that are fitted with
V7.1 software or above..
Double Pole
This wiring configuration can only be used on the Premier
LCD/LCDL remote keypads. It provides monitoring for alarm
and tamper using normally closed detection devices. Ensure
that the zone is programmed for Double EOL operation (see
page 26). The zone must be wired as follows:
2 Normally
Closed Contacts
1 Normally
Closed Contact
Premier LCD/LCDL
Keypads
AT
Zone x
AT
Zone x
Tamper
Alarm
Alarm
Tamper
Tamper
Alarm

Premier 412/816/832 Installation Manual Installation
INS159 17
2-Wire Smoke Detector
Compatible 2-wire smoke detectors such as the ESL429AT
or System Sensor 2100TS can be connected as shown:
Output 1 Must be
Enabled for 2 Wire
Smoke Detectors
O/P 1
2-Wire
Smoke
Detector
Aux 12V +
E.O.L
1K
In In
Out Out
(+)
(+)
(-)
(-)
!Panel Output 1 must be enabled for 2-wire smoke
detection (see page 35 for details).
The jumper link fitted across JP1 (Enabled 2-Wire
Smoke Det.) MUST be removed.
The maximum number of detectors is 20.
Speaker/Bell Connections
The Siren/Spk output terminals on the main PCB can be
configured for Speaker or Siren/Bell operation.
Speaker Operation
When configured as speaker operation the output can be
used for driving 8 or 16 Ohm loud speakers as shown:
Siren/Spk
8 Ohm Speaker
Siren/Spk
8 Ohm Speaker
8 Ohm Speaker
8W
8W
8W
!The Siren/Spk output must be enabled for speaker
driver (see page 35 for details).
Siren/Bell Operation
When configured as bell operation the output terminals
provide up to 750mA of power for driving bells as shown:
Siren/Spk
Bell/Siren
+
-
The Siren/Spk output must be enabled for bell
driver (see page 35 for details).
Siren/Spk Supervision
The Siren/Spk output is supervised, if no warning devices
are fitted, either disable Siren Supervision (see page 36 for
details) or connect a 1KΩresistor between the Siren
terminals as shown:
Siren/Spk
1K
if no warning devices are fitted,
connect a 1K resistor as shown.
Telephone Line Connections
The control panel has a built in digital communicator and
modem, which is used for communicating with an alarm
receiving centre and for downloading. If either of these
features are used, a telephone line must be connected to
the control panel as shown:
TRT1R1
In from telephone provider
Out to premises telephone
Connect to earth or an earth rod
Failure to fit an earth cable may prevent proper
operation of the system and will invalidate the
Texecom warranty and product approvals.
!
"

Installation Premier 412/816/832 Installation Manual
18 INS159
Panel Outputs 1 - 8
The control panel has eight programmable outputs, which
can be used to drive auxiliary devices such as relays, LED’s,
smoke detectors etc. The table below shows the electrical
characteristics for each output:
No Supervised Max Current Type
1 Yes 1 Amp Switched –ve
2 Yes 1 Amp Switched –ve
3 No 100mA Switched –ve
4 No 100mA Switched –ve
5 No 100mA Switched –ve
6 No 100mA Switched –ve
7 No 100mA Switched –ve
8 No 100mA Switched –ve
Output Wiring
The figure below shows some typical wiring examples:
LED
1K
Panel Outputs
Aux 12
123
LED Indication
12V Buzzer
Panel Outputs
Aux 12
123
Relay Driver
Diode
(IN4148)
Relay
Panel Outputs
Aux 12
123
Output Supervision
Panel outputs 1 and 2 are supervised, if either output is
unused, either disable the relevant output supervision (see
page 36 for details) or connect a 1KΩresistor between the
relevant output terminal and Auxiliary 12V+ as shown:
1
1K
If output 1 or 2 is unused,
connect a 1K resistor as shown.
2
1K
Panel Outputs
Aux 12

Premier 412/816/832 Installation Manual Commissioning & Troubleshooting
INS159 19
3. Commissioning & Troubleshooting
Commissioning
Once ALL connections have been made to the control panel
and power is ready to be applied, you should read this
section before continuing.
When applying power for the first time, the factory
default settings will automatically be loaded. The default
settings ensure that the control panel software is reset
and all programming information is loaded into memory.
For a complete list of factory default settings, please
refer to the accompanying “Installation Records and
Defaults” booklet.
!The control panel will only load the default values if
the lid tamper is open.
•Connect the black battery lead to the negative (–)
terminal of the standby battery and the red battery lead
to the positive (+) terminal of the standby battery. The
green power light on the main PCB will flash whilst the
default values are being loaded.
•If the system has gone into an alarm condition, enter the
default Master User code &'(). The alarm
tone will then stop.
•To access the Engineer Programming Menu, enter the
default Engineer code !#$% and press
,followed by *. All the zone lights will illuminate.
•Program the system date and time, see page 67.
•Program the system as described in the next section
(Programming the Control Panel).
•Perform a walk test as described on page 67.
Remember that some powered detectors (e.g. PIRs and
combined technology detectors) take several minutes to
warm up and become operational.
•Test the internal sounder, external sounder and strobe
as described on page 67.
•Replace the lid and secure with the two lid screws
supplied - do not over-tighten.
•Replace the screw covers.
•Press ,to leave the programming menus. All the
zone lights will turn off.
•The Service light will be flashing to indicate that action
is required. Switch on the mains supply to the control
panel. The Service light will stop flashing and stay on
continuously.
Installation is now complete and the system is
ready for use.
Troubleshooting
Power Faults
No Power to Unit (mains only)
•Check the mains block fuse and replace if blown.
•Check for any loose wires at the mains block, the
transformer and the AC terminals on the PCB.
•Check the mains block is connected correctly; live to
live (brown), neutral to neutral (blue).
No Power to Unit (battery only)
•Make sure the “Kick Start” pins have been shorted
together.
•Check for any loose wires at the BATT terminals on the
PCB.
•Check that the battery wires are connected correctly;
red from BATT+ to the battery positive [+], black from
BATT- to the battery negative [–].
Remote Keypads
Keypad Does Not Operate at All
•Check that the remote keypad is wired correctly from
the control panel.
•Check that the network fault indicator is off. If the
indicator is on, the electronic fuse has activated
indicating a short circuit across the [+] and [–] of the
network terminals.
Keypad Does Not Accept Access Codes
•If the system has more than one remote keypad check
that each keypad is addressed differently, see page 10
for details. The address of a keypad can be checked by
pressing the -and .keys together, the address is
displayed by the relevant zone light.
•Check that the remote keypad is wired correctly from
the control panel.
•If the remote keypad is on a cable run that is longer
than 100m, check the voltage between the [+] and [–]
terminals at the remote and ensure that it measures no
less than 10.0V.
•Check that you are using the correct Access code. The
default Engineer code is !#$% and the
default Master User code is &'().
•Check that the User code you are using is not “Time
Locked”, if the User code is time locked then the
Access code will only be accepted when Control Timer
1 is off, see page 64 for further details.

Commissioning & Troubleshooting Premier 412/816/832 Installation Manual
20 INS159
Keypad Does Not Generate Alarm Tones etc.
•Each keypad can be configured so that the alarm, entry,
exit, chime tones etc. can be enabled or disabled.
Check that the keypad has been programmed correctly,
see page 40 for details.
Keypad Emergency Keys Do Not Operate
•Each keypad can be configured so that the emergency
keys FIRE, POLICE and MEDICAL can be enabled or
disabled. Check that the keypad has been programmed
correctly, see page 40 for details.
Remote Expander
Expander Does Not Operate at All
•Check that the expander is wired correctly from the
control panel.
•Check that the network fault indicator is off. If the
indicator is on, the electronic fuse has activated
indicating a short circuit across the [+] and [–] of the
network terminals.
System Does Not Recognise Zones 9 to 16
•If the expander is on a cable run that is longer than
100m, check the voltage between the [+] and [–]
terminals at the remote and ensure that it measures no
less than 10.0V.
The Speaker Output Does Not Work
•The expander can be configured so that the alarm,
entry, exit, chime tones etc. can be enabled or disabled.
Check that the expander has been programmed
correctly, see page 43 for details.
•The speaker volume on the expander is electronically
adjustable. Check the volume is set to the desired level,
see page 43 for details.
Zones
One or More Zones Show an Alarm
•Each zone on the system can be configured for different
wiring options. Check that the zones are programmed
for the correct wiring configuration, see page 26 for
further details.
•Check that the zone is wired correctly, see page 13 for
further details.
Service Faults
If the Service light is on or flashing then the system has
detected one or more fault conditions, for details on how to
view and acknowledge Service Faults see page 75.
On Power-Up the Service Light is On
•When the system is powered-up the system date and
time are incorrect. This will cause a Date/Time Loss
fault, to clear this fault, program the system date and
time, see page 67.
•If the battery presence check is enabled the system will
check the battery every 30 seconds. If the system does
not have a battery connected then a battery fault will be
generated. To clear this fault either connect a battery or
disable the battery presence check, see page 35.
•Panel outputs 1 and 2 are supervised outputs, if you
have not connected a device to either of these outputs
the system will generate an output fault. To clear this
fault either fit 1K load resistors between the outputs and
+12V, see page 18 or disable the monitoring of outputs
1 and 2, see page 36.
•The Siren output is a supervised output, if you have not
connected a device to this output the system will
generate a siren fault. To clear this fault either fit 1K load
resistors between the siren terminals, see page 17 or
disable the monitoring of the siren output, see page 36.
Communicator
The Communicator Will Not Dial
•By default the communicator is disabled, check that the
communicator is enabled, see page 51.
•Check that the telephone line has been correctly wired
to the control panel.
•Check that the primary telephone number is
programmed correctly, see page 52.
•Check that the primary account number is programmed
correctly, see page 52.
•Check that the primary protocol is programmed
correctly, see page 52.
•Check that the primary dial attempts is not programmed
as zero, see page 52.
•Check that the primary reporting partitions have been
programmed correctly, see page 53.
•Check that the primary reporting options have been
programmed correctly, see page 53.
Communicator Dials But Does Not Communicate
•Check that the primary telephone number is
programmed correctly, see page 52.
•Check that the primary account number is programmed
correctly, see page 52.
•Check that the primary protocol is programmed
correctly, see page 52.
•If you are using either Pulse or Express formats check
that the protocol is configured correctly, see page 53.