Texecom Veritas R8 Plus User manual

INS045-14
Veritas R8 Plus/Veritas Excel
Installation Manual

Contents Veritas R8 Plus &Excel Installation Manual
2 INS045-14
Contents
1. Quick Reference and Factory Settings................ 4
Programming Guide ................................................................. 4
Reference Table ........................................................................ 5
Miscellaneous Options ............................................................. 6
2. System Overview .................................................. 7
System Architecture.................................................................. 7
Control Panels........................................................................... 7
Veritas R8 Plus & Excel ....................................................... 7
Remote Keypads....................................................................... 7
Veritas R8 Remote Keypad.................................................. 7
Veritas Excel Remote Keypad ............................................. 7
3. Installation............................................................. 8
Installation Sequence ............................................................... 8
Control Panel ............................................................................ 8
Mounting the Control Panel ................................................ 8
Wiring the Control Panel........................................................... 8
Control Panel PCB Layout........................................................ 9
Connecting AC Mains ............................................................. 10
Connecting Batteries .............................................................. 10
Installing Remote Keypads..................................................... 10
Cable Distances ...................................................................... 10
Keypad Addressing ................................................................ 10
Addressing for Excel Keypad............................................ 10
Addressing for Standard R8 Keypad ................................ 10
Configuring the Keypads........................................................ 10
Zone Connections................................................................... 11
Magnetic Contacts and Panic Buttons ............................. 11
Powered Detectors ............................................................ 12
End Of Line Technology......................................................... 13
10K/22K/33K ...................................................................... 13
4K7/2k2 .............................................................................. 13
Global System Tamper ........................................................... 14
Speaker Connections ............................................................. 14
Internal Siren(s)....................................................................... 14
Wiring the External Sounder................................................... 15
Popular SAB Wiring Diagrams .......................................... 15
Wiring a Communicator.......................................................... 15
Wiring Example.................................................................. 15
Connecting a Computer ......................................................... 15
PC-Com................................................................................... 16
Commissioning (Initial Power Up).......................................... 16
Servicing the System .............................................................. 16
Trouble Shooting .................................................................... 17
No Power to the Unit (Mains Only) ................................... 17
No Power to the Unit (Battery Only).................................. 17
No Power to the Unit (Mains & Battery)............................ 17
Unit Does Not Accept Code .............................................. 17
Unit Will Not Set and Bleeps 10 Times ............................. 17
Unit Will Not Set and Bleeps 9 Times ............................... 17
Remove ALL Temporary Links. ......................................... 17
Unit Will Not Set and Bleeps 1 - 8 Times.......................... 17
Unit Goes Into False Alarm ............................................... 17
Unit Makes No Sound ....................................................... 18
System Operates but Keypad Makes No Sound ............. 18
External Sounder/Strobe Does Not Work......................... 18
The Panic Button Does Not Work ..................................... 18
Service Timers Cannot Be Programmed.......................... 18
4. Programming the Control Panel ........................ 19
Introduction ............................................................................. 19
The Programming Menu -  ............................. 19
Programming With an LCD Keypad.................................. 19
Available LCD Menus.............................................................. 19
The Miscellaneous Selections -  ........................... 20
Miscellaneous Selections Zero ................. 20
Miscellaneous Selections One .............. 20
Miscellaneous Selections Two .............. 21
Miscellaneous Selections Three ............ 22
Number of Alarm Activations (Re-arms) ..................... 22
Testing the Sounders, Strobe ..................................... 23
Walk Testing or ................................................... 23
Re-Loading the Factory Settings................................. 23
Programming the SW+ Output................................... 24
Configuring Remote Keypads ..................................... 24
Programming Zone Types -  ................................. 25
Description of Zone Types ................................................ 25
Push To Set........................................................................ 25
Inhibited Entry.................................................................... 25
Guard ................................................................................. 25
Fire ..................................................................................... 25
Tamper............................................................................... 25
Entry/Exit ............................................................................ 25
Personal Attack.................................................................. 25
Keyswitch ........................................................................... 25
24 Hour Zone Types.......................................................... 26
Programming the Zone Type - ...................... 26
Changing Part Set Zone Types -  ......................... 26
Programming Part Sets Zone Changes ............... 27
Changing Zones to Entry/Exit .............................. 27
Changing Zones to Inhibited Entry...................... 27
Changing Zones to Guard .................................. 27
Programming the Date and Time -  ...................... 27
Programming the Date ........................................ 27
Programming the Time ....................................... 28
Programming the Service Timers -  ...................... 28
Programming Service Timer One ........................ 28
Programming Service Timer Two ........................ 28
Programming Service Timer Three...................... 28
Programming EOL Values........................................... 28
Programming System Timers -  ............................ 29

INS045-14 3
The Seven Event Basic Log -  ............................... 29
Clearing the Seven Event Basic Log ................... 29
Displaying the Seven Event Basic Log..........
 -  ..... 29
Programming the Suites -  .................................... 29
Programming the Zone Disable Suite .................. 30
Programming the Zone Soak Test Suite .............. 30
Programming the Full Set Suite ........................... 30
Programming the Part Set Suites -  ................ 30
Programming the Chime Suite............................. 31
Programming the Cleaner Suite .......................... 31
Programming the Double Knock Suite ................. 31
Programming the Manual Omit Suite ................... 31
Programming the Zone Invert Suite..................... 31
Assigning Access Codes -  ..................... 32
User Number...................................................................... 32
Access Code...................................................................... 32
Access Level ...................................................................... 32
Access Types .......................................................................... 33
Changing Your Own Access Code........ 33
Assigning New Access Codes - ..................... 33
Programming Access Codes .....................
 -  ..... 33
Programming Access Levels .....................
 -  ..... 33
Displaying User Information  &  ...................... 34
Displaying Your User Number ........................... ..... 34
Displaying Your Access Level............................ ..... 34
The Communicator Interface -  ............................. 34
Programming Communicator Selections34
Testing the Communicator Interface ..... 35
The 250 Event Extended Log ................................. 35
Viewing the Extended Log ................................ 35
Event Log Descriptions ..................................................... 35
Programming Text - .................................... 36
Programming Zone Text ........................ 36
Programming User Name Text ............... 36
Banner Text........................................ 36
Broadcast Text ...................................... 36
Default Text........................................ 36
5. Specifications...................................................... 37
Control Panel........................................................................... 37
Power supply ..................................................................... 37
Electrical............................................................................. 37
Physical .............................................................................. 37
Environmental .................................................................... 37
Keypads ............................................................................. 37
Safety Notes....................................................................... 37
Warranty ............................................................................. 37
European Standards............................................................... 37
EN 50131............................................................................ 37
6. Installation Records............................................ 38
Installation Details.................................................................. 38
Maintenance & Call-Out Record............................................. 38
Access Code Table................................................................. 39

Quick Reference and Factory Settings Veritas R8 Plus &Excel Installation Manual
4 INS045-14
1. Quick Reference and Factory Settings
Programming Guide
Programming Option Option Code Programming Procedure Factory Setting
Miscellaneous Selections Zero  Select/De-select Option Number(s) to Press 
Miscellaneous Selections One  Select/De-select Option Number(s) to Press 
Miscellaneous Selections Two  Select/De-select Option Number(s) to Press 
Miscellaneous Selections Three  Select/De-select Option Number(s) to Press 
Number of Alarm Activations  Enter Number of Alarm Activations  Press 03
Test Sounders, Strobe, SW+  Press  in Turn Press 
Walk Test (Non-Latching)  Conduct Walk Test Press 
Re-Load Factory Settings  Press 
Switched Positive Output  Select Function to Press Set +Ve with Reset (6)
Configure Remote Keypads  View Display Press 

Zone 1 Zone Type  Select Zone Type to Press Entry/Exit (6)
Zone 2 Zone Type  Select Zone Type to Press Inhibited Entry (2)
Zone 3 Zone Type  Select Zone Type to Press Guard (3)
Zone 4 Zone Type  Select Zone Type to Press Guard (3)
Zone 5 Zone Type  Select Zone Type to Press Guard (3)
Zone 6 Zone Type  Select Zone Type to Press Guard (3)
Zone 7 Zone Type  Select Zone Type to Press Guard (3)
Zone 8 Zone Type  Select Zone Type to Press Guard (3)
Walk Test (Latching)  Conduct Walk Test Press 
Part Sets Which Change Zone Types  Select Part Set(s) to Press Parts Sets 1 & 3
Change into Entry/Exit Suite  Select Zone Number(s) to Press Zone 2 Included
Change into Inhibited Entry Suite  Select Zone Number(s) to Press No Zones Included
Change into Guard Suite  Select Zone Number(s) to Press Zone 1 Included
Program Current Date  Enter Date DD/MM/YY Press 
Program Current Time  Enter Time HH:MM:SS Press 
Program Service Timer 1 Date  Enter Date DD/MM/YY Press 
Program Service Timer 2 Date  Enter Date DD/MM/YY Press 
Program Service Timer 3 Date  Enter Date DD/MM/YY Press 
EOL Resistor Values  Select/De-select Option Number(s) or Press 

Full Set Exit Time (sec)  Enter Exit Time  Press 30 sec
Part Set Exit Time (sec)  Enter Exit Time  Press 30 sec
Full Set Entry Time (sec)  Enter Entry Time  Press 30 sec
Part Set Entry Time (sec)  Enter Entry Time  Press 30 sec
Bell Cut-Off Time (min)  Enter Cut-Off Time  Press 15 min
Error Tone Suspension Time (sec)  Enter Suspension Time  Press 10 sec
Bell Delay Time (min)  Enter Delay Time  Press 00 (Instant Bells)
Confirmation Time (min)  Enter Second Intruder Time  Press 45 min
Zone Soak Test Time (days)  Enter Soak Test Time  Press 14 days
Clear Seven Event Basic Log  Press 
Basic Log Event 1 (most recent)  View Display (Press for Extended Display) Press 
Basic Log Event 2  View Display (Press for Extended Display) Press 
Basic Log Event 3  View Display (Press for Extended Display) Press 
Basic Log Event 4  View Display (Press for Extended Display) Press 
Basic Log Event 5  View Display (Press for Extended Display) Press 
Basic Log Event 6  View Display (Press for Extended Display) Press 
Basic Log Event 7 (least recent)  View Display (Press for Extended Display) Press 

Veritas R8 Plus &Excel Installation Manual Quick Reference and Factory Settings
INS045-14 5
Programming Option Option Code Programming Procedure Factory Setting
Zone Disable Suite  Select Zone Number(s) to Press No Zones Included
Zone Soak Test Suite  Select Zone Number(s) to Press No Zones Included
Full Set Suite  Select Zone Number(s) to Press All Zones Included
Part Set Suite 1  Select Zone Number(s) to Press Zones 5, 6, 7 Omitted
Part Set Suite 2  Select Zone Number(s) to Press Zones 5, 6, 7 Omitted
Part Set Suite 3  Select Zone Number(s) to Press Zones 5, 6, 7 Omitted
Part Set Suite 4  Select Zone Number(s) to Press Zones 5, 6, 7 Omitted
Chime Suite  Select Zone Number(s) to Press No Zones Included
Cleaner Suite  Select Zone Number(s) to Press No Zones Included
Double Knock Suite  Select Zone Number(s) to Press No Zones Included
Manual Omit Suite  Select Zone Number(s) to Press Zone 1 Omitted
Zone Invert Suite  Select Zone Number(s) to Press No Zones Included
Program Your Own Code PIN  Enter New Code PIN  Press 
Program Code 1 PIN  Enter New Code PIN  Press 
Program Code 2 PIN  Enter New Code PIN  Press 
Program Code 3 PIN  Enter New Code PIN  Press 
Program Code 4 PIN  Enter New Code PIN  Press 
Program Code 5 PIN  Enter New Code PIN  Press 
Program Code 6 PIN  Enter New Code PIN  Press 
Program Code 7 PIN  Enter New Code PIN  Press 
Program Code 8 PIN  Enter New Code PIN  Press 
Display Your Own User Number  View Display Press 
Display Panel Type  View Display Press Z1, Z2, Z3 On
Program Code 1 Access Level  Select Access Level to Press Master User (5)
Program Code 2 Access Level  Select Access Level to Press Boss Engineer (8)
Program Code 3 Access Level  Select Access Level to Press Null (7)
Program Code 4 Access Level  Select Access Level to Press Null (7)
Program Code 5 Access Level  Select Access Level to Press Null (7)
Program Code 6 Access Level  Select Access Level to Press Null (7)
Program Code 7 Access Level  Select Access Level to Press Null (7)
Program Code 8 Access Level  Select Access Level to Press Null (7)
Display Your Own Access Level  View Display Press 
Communicator Interface Selections  Select/De-select Option Number(s) to Press 
Test Communicator Interface  Toggle Channel(s) to Press 
Reference Table
Number Test Outputs  SW= Function  Zone Types  Extended Display
0 All Off
1 Bell Set +Ve Push To Set Bell & Global Tamper
2 Strobe Alarm +Ve & Reset Inhibit Entry Power
3 Sounder Lo Reset Guard Lid Tamper (inc. RKP)
4 Sounder Hi Tamper Fire Line Monitor
5 SW+ Mains Fail Tamper RKP Off-Line
6 Engineer Hold Off Set +Ve & Reset Entry/Exit Code PIN Tamper
7 Walk Test PA Keypad PA
8 Entry/Exit Keyswitch EOL Tamper

Quick Reference and Factory Settings Veritas R8 Plus &Excel Installation Manual
6 INS045-14
Miscellaneous Options
Option Miscellaneous Selections Zero  Factory Setting
1 Cancel Strobe with Bell Off
2 Keypad PA (pressing and together causes PA alarm) Off
3 Single Button Setting On
4 Silent Part Set Confirmation Tone Off
5 EN 50131-1 Requirements Off
6 Time Limit Engineer Access Off
7 Reset Button Cancels Setting On
8 Automatically Omit a Mains Fail Condition (Auto-Omit AC Off) Off
Option Miscellaneous Selections One  Factory Setting
1 Internal Sounders Only on Unset Tamper Alarm On
2 Internal Sounders Only on Part Set Zone Alarm On
3 Internal Sounders Only on Part Set Tamper Alarm On
4 Silent Part Set (no exit tone on part set) Off
5 High Level Chime (chime at full volume) Off
6 Invert Bell Output (negative removed instead of negative applied, useful for SCBs) Off
7 Final Door Set (system sets 3 seconds after final door closure) Off
8 Unlock Engineer Code (re-loading factory settings restores default Engineer code) On
Option Miscellaneous Selections Two  Factory Setting
1 Engineer Reset on Any Alarm (see page 21) Off
2 Engineer Reset on Tamper Alarm (see page 21) Off
3 Disable User Ability to Omit Tamper Off
4 Code PIN Tamper (tamper alarm after 16 invalid key presses when unset) Off
5 Random Number Remote Reset (RNRR, see page 21) Off
6 Push To Set (see page 22) Off
7 Strobe Flash on Full Set (see page 21) On
8 Invert Switched Positive Output (off = negative removed, on = negative applied) Off
Option Miscellaneous Selections Three  Factory Setting
1 Mains Frequency (off = 50Hz, on = 60Hz) Off
2 EOL Tamper Alarm on Zone Short Circuit (S/C) Off
3 EOL Tamper Alarm on Zone Open Circuit (O/C) Off
4 Enable DD 243:2002 Options (see page 22) Off
5 Enable Confirmation Signal After Entry Time Out Off
6 Operation of a Keyswitch Zone is Momentary (Momentary KEYSW) Off
7 Automatically Omit Zone on Alarm Off
8 Automatically Omit Keyswitch Zone when EOL Tampered Off
Option Communicator Selections  Factory Setting
1 Communicator Outputs Latch until System is Reset On
2 Line Monitor Input causes Tamper Alarm on Line Cut Off
3 Invert Communicator Outputs (off = active low, on = active high) Off
4 Invert Remote Reset Input (off = active if negative removed, on = active if negative applied) Off
5 Remote Reset Input Silences Internal Sounder during Alarm Off
6 Remote Reset Input Clears Engineer Reset (see page 21) Off
7 Silent PA Off
8 Enable 90 Second Abort Time Limit On

Veritas R8 Plus &Excel Installation Manual System Overview
INS045-14 7
2. System Overview
System Architecture
Control Panels
Veritas R8 Plus & Excel
8 fully programmable Single Pole with Global Tamper
or End Of Line zones
8 User Codes
LED and/or LCD keypads
Up to 6 keypads
Engineer keypad facility
4-wire data network (standard 7/0.2 alarm cable)
4 Part Suites plus Full Set
8 communicator outputs
10 character zone text
16 character Banner Message
8 character User Name text
Remote Keypads
Veritas R8 Remote Keypad
LED keypad (8 zone indicators, tamper, power and unset)
Solid keypad buttons
Keypad cover
Keypad PA (3 & 9)
4-wire connection to remote keypad network
Built in Piezo sounder
Veritas Excel Remote Keypad
32 Character LCD keypad (power and unset indicators)
Tactile sealed rubber keypad
Keypad cover
Keypad PA (3 & 9)
4-wire connection to remote keypad network
Built in Piezo sounder
4 Part Suites plus Full Set
8 x 100mA
Outputs
Bell Tamper Input
Auxiliary Tamper Input
Veritas R8 Plus
Veritas Excel
Veritas Excel Keypad
4 Wire Keypad Network
6 Keypads (mixed)
8 Zone Inputs
PC-Com
PC and for
Local Upload/Download
PC-Com
Unset
Bell/Strobe Outputs
Omit
Yes
Part
Chime
Full Prog
Reset 2 abc
No
13 def
6 mno
9 wxyz
5 jkl
8 tuv
0
4
ghi
7 pqrs
Veritas Excel


456
123
7890
Unset
Zones
87654321
Tamp er
FULL
PART
PROG
OMIT
RES ET

Installation Veritas R8 Plus &Excel Installation Manual
8 INS045-14
3. Installation
Installation Sequence
Before attempting to install the alarm system, read this section.
Once you have an overall understanding of the installation
sequence, carefully work through each step.
1. Design the Layout
Make a rough sketch of the premises to get an idea of where the
alarm detection devices, keypads etc. are to be located.
2. Mounting the Panel
The control panel should be mounted in a dry area close to an
unswitched AC power source.
You must complete all wiring before connecting the battery
or applying AC mains to the control panel.
3. Installing the Keypads
Mount and connect the keypads to the control panel (see page 10
for wiring details).
4. Installing the Alarm Detection Devices
Install the detection devices, PIR’s, Contacts, PA Buttons etc. and
connect them to the control panel (see page 11).
5. Install the External Sounder
Install the external sounder and connect to the control panel (see
page 15).
6. Other Wiring
Complete all other wiring including speakers and output
connections etc. (see pages 14 - 15 for wiring details).
7. Applying Power to the Control Panel
Once steps 1 to 6 are completed, power can be applied to the
control panel.
If you need to load the factory default settings (see page
16).
Power should always be connected in the following order:
Connect the red battery lead to the positive terminal of the
battery and then connect the black battery lead to the
negative terminal.
Connect the AC mains.
8. Programming the Control Panel
Please refer to section 4 for instruction on programming the
control panel.
9. Testing the System
Test the system thoroughly to ensure that all features and functions
operate as required (see page 23).
Control Panel
Mounting the Control Panel
Mount the control panel on a flat, plumb wall using at least three
appropriate screws. The rear casing has been designed with a
central key-hole slot so that mounting is possible without removing
the Printed Circuit Board (PCB). The angled slot in the lower
corner has been provided to allow the panel to be levelled easily. If
the PCB has to be removed, carefully pull back the two front PCB
securing clips, lift the front of the PCB and slide it downward. To
replace the PCB simply reverse the above procedure.
It is essential to ensure that none of the fixing slots or cable
entries are accessible after fixing.
Mains cabling must be secured (e.g. with a cable tie) to one
of the anchor points provided.
Wiring the Control Panel
WARNING: ELECTRICITY CAN KILL
BEFORE connecting the control panel
ALWAYS disconnect the supply at the
consumer unit. If in ANY doubt consult
a qualified electrician.
ONLY connect the mains supply to the mains terminal
block, NEVER connect the mains supply directly to the PCB.
ALWAYS refer to National Wiring Regulations when
conducting installation.
An appropriate and readily accessible disconnection device
(e.g. an unswitched fused spur) MUST be provided as part
of the installation.
The disconnection device must NOT be fitted in a flexible
cord.
Where identification of the neutral in the mains supply is
NOT possible a two-pole disconnection device MUST be
used.
The building mains supply MUST incorporate appropriate
short-circuit backup protection (e.g. a fuse or circuit
breaker) of High Breaking Capacity (HBC, at least 1500A).
Use mains cable of adequate carrying capacity for the rated
current (i.e. at least 0.75mm2).

Veritas R8 Plus &Excel Installation Manual Installation
INS045-14 9
Control Panel PCB Layout
Z1 Z3Z2 Z4
+
TR
-
F1
1 2
Z5 Z7
Z6 Z8
123456
F3 F4
F2
F5
78
4 5 7
SAB
0V +12V (Unfused) Zone Lockout Abo r t Intruder Se t/U ns e t PA Fire Line Monitor Remote Reset Duress Confirmed
1: AC Input
Connected to the 16.5V transformer.
DO NOT CONNECT THE MAINS SUPPLY TO THE AC INPUT
TERMINALS ON THE PCB.
2: Battery Connections
A 12V rechargeable battery must be connected to these terminals in
order to provide continuous system operation in the event of an AC
Mains failure (see page10).
3: External Sounder Connections
These terminals are used for connecting to an external sounder unit
(see page 11 for wiring details).
4: Loudspeaker Connections
These terminals can be used for connecting up to one 16or two
8loudspeakers (see page 14).
5: Auxiliary 12V Connections
These terminals are for connecting devices that require 12V power
(protected by a 1A fuse F1).
6: SW+ Connections
These terminals are for connecting devices that require 12V power
(protected by a 1A fuse F1).
7: Auxiliary Tamper Connections
These terminals can be used for monitoring the box tamper of
auxiliary devices such as power supplies etc. (see page 14).
8: Keypad Network Connections
These terminals provide connection for the keypads. The ‘+’ and ‘–’
terminals provide power whilst the ‘T’ transmits data and ‘R’
receives data (see page 10).
9: Programmable Zones 1 - 8
These terminals provide the connections for the 8 zones (see page 11).
Each zone is also fully programmable (see page 25).
10: Com1
A portable Engineers keypad or a computer (using a
PC-Com) can be plugged on here to make programming and
testing the system easier.
When using a keypad as an Engineers keypad, the keypad’s
address must all be set to 6 (see page 10).
11: Low Volume Control
This variable resistor controls the volume level of advisory
(entry/exit) tones (turn anticlockwise to increase volume).
12: Communicator Interface
These terminals provide UNFUSED 12V power; a remote reset input,
a line fault input and 8 low current (100mA ‘-ve’ applied) outputs and
would normally be used when connecting a stand-alone
communicator to the control panel (see page 15).
13: Power Indicator
This LED will be ON when AC mains is present on the control panel
and will flash when there is no AC mains present on the control
panel.
14: Box Tamper Switch
This switch provides tamper protection for the main control panel in
case of unauthorised access. To disable the box tamper, fit a
jumper link across the box tamper pins (if fitted).
F1 - F5: Protection Fuses
The following fuses are provided:
Fuse Description Rating
F1 Battery 1 Amp
F2 Bell and Strobe 1 Amp
F3 Auxiliary 12V and Speaker 500mA
F4 Keypad Network 500mA
F5 Power Supply 1.6 Amp

Installation Veritas R8 Plus &Excel Installation Manual
10 INS045-14
Connecting AC Mains
The AC Mains supply is connected to a 3 way ‘Euro Type’ fused
terminal block, which is fitted with a fuse (see page 37).
All other wiring MUST be carried out before AC mains is connected to the control
panel.
After connecting the AC Mains, fit the mains cover, this can be found in the spares
bag.
Connecting Batteries
Up to one 12V 7Ah battery can be fitted inside the control panel to
provide continued operation in the event of an AC mains failure.
All other wiring MUST be carried out before the battery is connected to the control
panel.
Connect the red battery lead to the positive terminal of the battery
and connect the black battery lead to the negative terminal of the
battery.
+
-
Battery
12V
2.1Ah - 7Ah
Battery
+
_
EN50131 Battery Installation (8 & R8 only)
Step 1: Screw 2 x battery clamps into holes provided in the rear
of the panel.
Step 2: Fit battery into place, position the clamps against the
top face of the battery and tighten screws.
Installing Remote Keypads
A maximum of 6 remote keypads can be connected to the keypad
network. The Veritas R8 Plus and the Veritas Excel supports both
LED and LCD keypads.
The networks are made up of four terminals incorporating power and
data. To ensure correct operation, all four terminals on the device must
be connected to the corresponding terminals on the control panel, or
previous keypad. The table below shows each terminal and its
description:
Terminal Description
+ +12V Supply
- 0V Supply
T Transmit Data
R Receive Data
Devices can be connected using 4-core cable. However, it is recommended
that 6 or 8-core cable is used as the spare cores can be used to ‘Double Up’
on the power connections if needed.
Standard 7/0.2 alarm cable can be used for most installations. However, under
certain conditions it may be necessary to use screened cable.
Cable Distances
The maximum recommended distance for devices when using
standard 7/0.2 alarm cable is:
100m for each branch when using the star (parallel)
configuration
When using a daisy chain (series) configuration the maximum
distance will depend on the number of devices connected on
the chain. The more devices that are connected, the shorter
the distance to the last device (this is due to voltage drop in
the cable)
Whichever method of wiring configuration is used, ensure that the
voltage between the ‘+’ and ‘–’ terminals at each device is no lower
than 10.0V when the system is running on the standby battery.
Keypad Addressing
Each keypad MUST be given a different address using the DIP
switch on the PCB as follows:
Addressing for Excel Keypad
Address DIP 1 DIP 2 DIP 3 DIP 4
1 N/
A
Off Off Off
2 N/
A
Off Off On
3 N/
A
Off On Off
4 N/
A
Off On On
5 N/
A
On Off Off
6 N/
A
On Off On
Addressing for Standard R8 Keypad
Address DIP 1 DIP 2 DIP 3 DIP 4
1 N/
A
Off Off Off
2 Off On Off On
3 Off Off On Off
4 Off Off Off On
5 On Off Off On
6 Off On Off On
NEVER set two RKPs to the same address. Keypads are factory set to Address 1. If
the keypad is powered but offline (i.e. T and R not connected) it will display its
address. If an invalid address is selected, the keypad will sound an error tone.
Configuring the Keypads
Configuring keypads is described on page 24
L
E
N
To t r a n s f o r m e r
FUSE

Veritas R8 Plus &Excel Installation Manual Installation
INS045-14 11
Zone Connections
Detection devices such as PIR’s, Door Contacts, PA Buttons etc. are all connected to the 8 zone terminals on the Veritas R8 Plus and Veritas
Excel control panel.
If a zone is not being used it should be either linked out or disabled (see page 30).
Magnetic Contacts and Panic Buttons
These are connected to one of the eight terminal pairs labelled Z1 to Z8 on the control panel.
Figure 1 - Wiring Magnetic Contacts
Figure 1a - Wiring a Single Magnetic Contact to a Zone (see also Figure 4).
Figure 1b - Wiring Multiple Magnetic Contacts to a Zone (see also Figure 4).
Mixing powered detectors and magnetic contacts on one zone is easiest if the wiring is taken from the control panel to the powered
detectors first.

Installation Veritas R8 Plus &Excel Installation Manual
12 INS045-14
Powered Detectors
Always consult the manufacturer's connection instructions. Powered detectors are connected to one of the eight terminal pairs labelled Z1 to Z8
on the control panel and are powered from the two terminals labelled AUX on the control panel as follows:
Terminal Connect To Suggested Colour
AUX+ Detector Positive Supply (+12V) White
AUX- Detector Negative Supply (0V) Green
Figure 2 - Wiring Powered Detectors
Power is wired in parallel, whereas normally closed alarm loops are wired in series, (normally open alarm loops are wired in parallel).
Mixing powered detectors and magnetic contacts on one zone is easiest if the wiring is taken from the control panel to the powered
detectors first.
BS 4737 requires that if two or more powered detectors are connected to one zone, they must each have an audible or visual latching
indication or both, except on an entry/exit route.
Figure 2a - Wiring a Single Powered
Detector to a Zone
(see also Figure 4).
Figure 2b - Wiring Multiple Powered
Detectors to a Zone
(see also Figure 4).

Veritas R8 Plus &Excel Installation Manual Installation
INS045-14 13
End Of Line Technology
Those already familiar with End of Line (EOL) Technology
(sometimes referred to as Balanced Zones) may wish to skip this
section.
End of Line Resistance is a technique which, by adding resistance
at the last detector in the loop, provides each loop with its own 24
hour tamper protection.
The panel can use two different types of EOL resistors, traditional
Texecom 4K7/2K2, or Veritas values 10K/22K/33K. See page 28
for programming details.
10K/22K/33K
The panel can distinguish up to four possible states; low
resistance (10k) is interpreted as zone clear, high resistance
(33k) is interpreted as zone in fault. Short circuit may optionally
be interpreted as tampering or zone clear. Open circuit may
optionally be interpreted as tampering or zone in fault.
Resistors are coded with coloured bands to identify the different
values, as follows:
Resistor Colour Code
10kBrown, Black, Orange, Brown
22kRed, Red, Orange, Brown
33kOrange, Orange, Orange, Brown
Thus there are four possible configurations depending on the
options selected. These include normally closed operation (a
Global System Tamper zone is provided) and become
progressively more secure, as follows:
The control panel is supplied with links fitted across the eight zones
(Z1 - Z8), the Global System Tamper (TAMP) and Bell Tamper (SAB
C, D) to simulate closed circuits.
These links are removed during installation as each zone is
connected.
The Global System Tamper zone will typically only be used with
normally closed operation.
If a zone is not required then the link should be left in place.
If EOL operation is selected and a zone is not required then the zone
link should be replaced with a 10K resistor (supplied).
When wiring a 24 Hour zone (Fire, PA and Tamper), such as a panic
button, it may be more convenient to fit the EOL resistor(s) in the
panel than in the detector.
Figure 3 - EOL Wiring
Miscellaneous Option 3.2 (S/C = Tamper) Off
Miscellaneous Option 3.3 (O/C = Tamper) Off
ALARM LID
ZONE TAMPER
Figure 3a - Normally Closed Operation.
Miscellaneous Option 3.2 (S/C = Tamper) On
Miscellaneous Option 3.3 (O/C = Tamper) Off
10K ALARM LID
ZONE
Figure 3b - "American" Operation.
Miscellaneous Option 3.2 (S/C = Tamper) Off
Miscellaneous Option 3.3 (O/C = Tamper) On
33K
ALARM LID
ZONE
Figure 3c - "European" Operation (one detector
per zone).
Miscellaneous Option 3.2 (S/C = Tamper) On
Miscellaneous Option 3.3 (O/C = Tamper) On
22K
10K ALARM LID
ZONE
Figure 3d - High Security Operation (one detector
per zone).
4K7/2k2
2 Normally
Closed Devices
1 Normally
Closed Device
Ta m p e r
E.O.L
Ala rm
Zone 1
4k7

2k2

Ta m p e r
E.O.L
Alar m
Zone 1
4k7

Ta m p e r
E.O.L
Alar m
4k7

2k2


Installation Veritas R8 Plus &Excel Installation Manual
14 INS045-14
Global System Tamper
This is connected to the terminal pair labelled TAMP on the control panel. All the individual zone tamper loops should be
wired in series.
Figure 4 - Wiring the Global System Tamper
The control panel is supplied with a link fitted across the Global System Tamper to simulate a closed circuit. This link would usually be
removed during installation. However the Global System Tamper will typically only be used with normally closed operation, with EOL
operation the tamper link would usually be left in place.
Speaker Connections
This output can be used for driving up to one 16or two 8loudspeakers as shown below:
The total load including the built-in speaker must not be less than 16
 (e.g. 1 x 16  speaker, 2 x 8  speakers in series, etc.).
The polarity of extension speakers is usually unimportant, however, the polarity of the L/S terminals is indicated by a + and -.
Internal Siren(s)
If required these are connected to two of the external sounder connections, in addition to the external sounder, as follows:
Terminal Connect To
A Siren Positive Supply (+12V)
B Siren Negative Activate/Negative Supply (0V)

Veritas R8 Plus &Excel Installation Manual Installation
INS045-14 15
Wiring the External Sounder
Always consult the manufacturer's connection instructions. The
external sounder and strobe are connected to the five terminals
labelled SAB on the control panel as follows:
Terminal Description
A Permanent Positive Supply (+12V)
B Switched Negative to Activate Sounder
C Negative Tamper Return
D Permanent Negative Supply (0V)
S Switched Negative to Activate Strobe
Figure 5 - Typical SAB Connections
An external sounder is often referred to as a 'bell' or 'bell-box'
even when it is actually an electronic siren.
The control panel is supplied with a link fitted across the Bell
Tamper to simulate a closed circuit. This link would usually
be removed during installation.
If the strobe is a separate unit take the strobe positive supply
from 'A' as well.
A self-activating bell/sounder (SAB) has a built-in battery.
After connecting this battery the sounder will usually sound
until its cover is fitted and it is supplied with power from the
control panel.
Terminal B may be programmed as switched negative
removed rather than switched negative applied to activate
sounder (see page 21). This is useful for SCBs where B
would then be used to provide the permanent negative
supply.
Popular SAB Wiring Diagrams
The following diagrams illustrate how to connect the control panel
to the most popular makes of SAB:
Texecom Odyssey.
Figure 6d - Volumatic Flashguard.
Wiring a Communicator
The control panel has eight outputs, which can be used for
connecting to a stand-alone communicator. The table below shows
the characteristics for each output:
Terminal Type Current Operation
1 Fire 10mA Switched 0V
2 PA 10mA Switched 0V
3 Intruder 10mA Switched 0V
4 Set/Unset 10mA Switched 0V
5 Abort 10mA Switched 0V
6 Zone Lockout 10mA Switched 0V
7 Duress 10mA Switched 0V
8 Confirmed 10mA Switched 0V
L/M Line Monitor N/A 0V removed = Fault
R/R Remote Reset N/A 0V applied to reset
The operation of ALL outputs can be inverted if required (see
page 34).
It is NOT possible to invert the individually outputs.
Following an alarm, the Zone Lockout output will activate at
the end of the 2nd Intruder time if any zone remains open.
Do not use non-latching communicator outputs if selecting
Automatic Omit (see page 22).
The operation of the R/R input may be inverted from 0V to
reset to 12V to reset if required (see page 34).
The L/M input should be connected to 0V (AUX-) if not
required, otherwise Bell Delay will not operate.
Wiring Example
The diagram below shows a typical wiring example:
Control
Panel
Power
134
5
678
12V 0V
Stand Alone
Communicator
C
DC+ L/M
DC-
1
345678
Channel Inputs
Programmed
as Positive
Removed
Line Fault
Communicator
Interface
For details on testing the communicator outputs, see page
35.
Connecting a Computer
The Veritas R8 Plus and Veritas Excel both support local uploading
and downloading between the control panel and a PC running Veritas
UDL software. Uploading and Downloading can be used to program
and interrogate the control panel.
PC-Com
Box
Tamp er
F1
Com1
PL1
Remote
Keypad
F3 F4
F2
F5
Power
LED1
Aux&
Speaker
S D C B A
Tamp
Strb 0V Bell+12V Tamp SW+
+ -
Aux
+ -
LS
- +
Batt A.C.
SW1
JP1
Batter y
PowerSu pply
Bell
&Str o be

Installation Veritas R8 Plus &Excel Installation Manual
16 INS045-14
PC-Com
In order to connect a computer to the control panel, a PC-Com lead
is required.
The PC-Com has a plug at either end of the cable. The
9-way D-type connector is for connection to a serial port on a
computer and the 5-way Molex connector is plugged onto Com 1
on the control panel.
Commissioning (Initial Power Up)
ALWAYS Ensure the mains is off
BEFORE removing the front cover
Connect the black battery lead to the negative (-) terminal of the
standby battery and the red battery lead to the positive (+) terminal
of the standby battery. All the indicator lights will come on. After 10
seconds the zone lights will turn off and a repeating 9 bleep error
tone will start.
To Load Factory Settings
Apply power to the control panel and press
OR press and release the lid tamper
spring 3 times BEFORE the zone lights turn off
and the repeating 9 bleep error tone starts
Enter the factory set User code . The error tone
will stop.
Enter the factory set Engineer code  and press
to access the Programming Menu and disable 24
Hour zones (Fire, PA and Tamper) via the Engineer code. All
the zone lights will illuminate.
Perform a Walk Test as described in on page 23. Remember
that some powered detectors (e.g. PIRs and Combined
Technology Detectors) take several minutes to warm up and
become operational.
Test the internal sounder, external sounder and strobe as
described on page 23. To adjust the low-level volume use the
control 'pot' on the PCB (see page 9), volume increases
anti-clockwise. If the system fails to operate as expected check
that the mounting and wiring are as per the instructions.
Correct any mistakes and repeat the test (see page 17, Trouble
Shooting).
Replace the lid and secure with the two lid screws supplied -
do not over-tighten.
Fit the screw covers, these can be found in the spares bag.
Press to leave the Programming Menu. All the zone
lights will turn off.
The Power light will be flashing to indicate that action is
required. Switch on the mains supply to the control panel. The
Power light will stop flashing and stay on continuously. If the
factory settings (see page 4) are not appropriate then re-
program the system as described on see page 19.
If you have a meter:
Disconnect the battery & check the total non-alarm current
is less than 1A.
Reconnect the battery & check the total alarm current is
not more than 1A.
The total current is measured as follows:
Set your meter to DC current.
Connect your meter across F5 (power supply fuse).
Remove F5.
Record the current drain.
Replace F5.
Remove your meter.
To avoid accidentally powering down the system be sure to
follow all the above steps in order.
Installation is now complete and
the system is ready for use.
If the battery is flat or faulty the RKP may not accept key
presses.
When the system is full set, after the exit period, the external
strobe will flash for approximately 6 seconds (this option can be
de-selected, see page 21).
Servicing the System
ALWAYS Ensure the mains is off
BEFORE removing the front cover
The Power light on the control panel is a status indicator for
the battery charging circuit, a steady light meaning normal. A
flashing light means action required - mains power can still
be present. ALWAYS use a suitable mains test instrument to
confirm that mains power is no longer present.
The transformer and heatsink may be hot during and after
use - do NOT touch.
Test the internal sounder, external sounder and strobe as
described on page 23. Perform a Walk Test as described on
page 23. Basic Log events may be viewed by following the
procedure described on page 29.
If it is necessary to remove the lid, first switch off the mains
supply to the control panel. Ensure that the Power light is
flashing, then use a suitable mains test instrument to confirm
mains power is no longer present.
Enter the 4 digit Engineer code  and press
to access the Programming Menu and disable 24
Hour zones via the Engineer code. All the zone lights will
illuminate.
Remove the screw covers by inserting a screwdriver into the
screw cover slot and turning anti-clockwise whilst applying
pressure outwards.
Unscrew the lid screws and remove the lid.
On completion replace the lid and secure with the lid screws -
do not over-tighten.


Veritas R8 Plus &Excel Installation Manual Installation
INS045-14 17
Replace the screw covers.
Press to leave the Programming Menu. All the zone
lights will turn off.
Switch on the mains supply to the control panel. The Power
light will stop flashing and stay on continuously.
Trouble Shooting
ALWAYS Ensure the mains is off
BEFORE removing the front cover
When replacing a fuse always observe the specified rating and
type - failure to do so is dangerous and will invalidate the warranty.
Fuses should comply with IEC 127.
No Power to the Unit (Mains Only)
Check the mains block fuse and replace if blown.
Check for any loose wires at the mains block, the transformer
and the AC terminals on the PCB.
Check the mains block is connected correctly; live to live
(brown), neutral to neutral (blue).
No Power to the Unit (Battery Only)
Check the battery fuse F1 and replace if blown.
Check for any loose wires at the BATT terminals on the PCB.
Check that the battery wires are connected correctly; red from
BATT+ to the battery positive (+), black from BATT- to the
battery negative (-).
No Power to the Unit (Mains & Battery)
Check the power supply output fuse F5 and replace if blown.
Disconnect all wires from the control panel SAB A and AUX+
terminals.
Check that links are only fitted in the correct places.
Check there are no wires shorting to the underside of the PCB.
Repeated blowing of the battery fuse F1 may indicate a faulty
battery.
Unit Does Not Accept Code
If using more than one RKP, check that each RKP has a
different address.
If using one or more RKPs, check that they are wired correctly.
If the remote keypad was connected after the control panel was
powered up, disconnect all power momentarily and reconnect.
This automatically configures all remote keypads on the system,
(also see page 24).
Check you are using the correct codes. Factory-set Engineer
code is . Factory-set User code is .
If using one or more RKPs on battery only, try using mains as
the battery may be flat.
Check that the codes have not been changed. If the codes
have been lost (see page 23).
Check that the membrane keypad tail is all the way home in its
connector on the PCB.
Unit Will Not Set and Bleeps 10 Times
The Power light on the panel will be flashing to indicate a power
fault, either mains fail or battery low volts.
The mains frequency may be set incorrectly (see page 22).
The procedure for setting the system in the event of a power
fault is described in the User Guide.
Unit Will Not Set and Bleeps 9 Times
The system has a tamper fault and the Tamper light will be on.
Using the extended display during Walk Test (see page 23) identify
the cause of the tamper fault:
If the extended display identifies the fault as an EOL tamper
then identify the zone(s) from the normal display and check
the zone wiring.
If the extended display identifies the fault as bell box tamper,
then the cause may either be Bell Tamper or Global System
Tamper. Temporarily replace the system tamper link (TAMP):
If the tamper fault persists then it is due to the Bell Tamper
- check the bell wiring, the bell lid and/or screw tamper,
and the bell wall tamper (if fitted).
If the tamper fault clears then it is due to the system
tamper. Remove the system tamper link and the tamper
fault will reappear - check the system tamper wiring and
the lid tamper on all detectors.
Remove ALL Temporary Links.
If the extended display identifies the fault as lid tamper, it may
refer either to the control panel or the remote keypad(s). Try
stretching the springs and ensure all connections are secure.
To set the system with a tamper fault use the following
procedure:
Enter the User code . Press or
. The system will sound a repeating series of
9 bleeps. Press . The display will illuminate the zones that
are about to be armed. Press . The Tamper light will turn
off. Press . The exit tone and exit timer will start.
To prevent repeated false alarms due to an intermittent tamper
fault when the system is unset, omit Tamper as described
above, then abort the setting procedure by re-entering the
User code.
To prevent Tamper from being omitted (see page 21).
Unit Will Not Set and Bleeps 1 - 8 Times
The system has one or more zone faults and the corresponding
zone light(s) will be on.
Ensure that the zone is closed (doors shut, no movement in
PIR detection area).
Check the zone wiring and ensure all connections are secure.
Check that detectors are powered correctly (i.e. correct
polarity).
Unit Goes Into False Alarm
Check that the terminal screws are fully down on all terminals
but do not over tighten.
If you have a meter use it to check the loop resistance (wires
that run under carpets are easily damaged).


Installation Veritas R8 Plus &Excel Installation Manual
18 INS045-14
Unit Makes No Sound
Check that the variable resistor (pot) on the PCB which
controls the volume of low level tones is NOT turned fully
clockwise. The volume increases as the pot is turned anti-
clockwise.
Check the auxiliary fuse F3 and replace if blown.
Check the speaker connections to the L/S terminals on the
PCB.
System Operates but Keypad Makes No Sound
If an older version remote keypad has been fitted the system
must be programmed for old style sounds as follows: Enter
the Engineer code , press , enter
, press , press , press .
External Sounder/Strobe Does Not Work
Check wiring connections by referring to the diagrams on page
15.
Check the bell/strobe fuse F2 and replace if blown.
To check the external sounder make a temporary connection
between SAB B and D.
To check the strobe make a temporary connection between
SAB S and D.
The Panic Button Does Not Work
Check that the Zone Type of the zone to which the panic button
is connected is programmed as PA (see page 26).
Check that the zone to which the panic button is connected is
not omitted in part set (see page 30).
Check that the Zone Type of the zone to which the panic button is
connected is not changed in part set (see page 26).
Older version remote keypads do NOT support Keypad PA
(pressing and together), see System Operates but
Makes No Sound, above.
Service Timers Cannot Be Programmed
Programming the service timers (, , ) is prevented
unless the current date () has been programmed since the last
power-up (see page 27).

Veritas R8 Plus &Excel Installation Manual Programming the Control Panel
INS045-14 19
4. Programming the Control Panel
Introduction
Programming is usually unnecessary as the factory settings have
been carefully selected to suit most installations without alteration.
However all functions are fully programmable for Complete
Control.
The Programming Menu  - 
The Programming Menu can only be accessed when the control
panel is unset.
The display will normally look like this:
123 4 56 7 8 Unset
Tamper
Zones


Enter your 4-digit Engineer code (factory set to ).
The display will look like this:
12345678 Unset
Tamper
Zones


If no keys are pressed, the display will revert back to normal
after 16 seconds.
Press , the display will look like this:
12345678 Unset
Tamper
Zones




The various programming options are then selected by entering a
2-digit Option code . The Programming Procedure then
depends upon the programming option selected as detailed in the
following sections. On completion, each programming option
reverts to the Programming Menu, allowing other programming
options to be accessed. To exit the Programming Menu press
, the system will revert to unset.
To abort programming at any stage (and preserve the
original setting) press , the system will revert to the
Programming Menu.
24 Hour zones (Fire, PA and Tamper) are disabled when the
Programming Menu is accessed via an Engineer code.
To omit zones, set chime or change the User code, refer to
the User Guide.
The system programming is retained even in the event
of complete loss of power.
Programming With an LCD Keypad
There are two ways to select options whilst in the Programming
mode:
1. Select an option directly by entering a 2-digit Option code
.
All of the programming examples shown in this section
use this method of programming.
2. Using the key to scroll up and down through the menu
options and then pressing or to access the
menu options.
Wherever a symbol appears on the display, the
key can be used to search through the various
menu options. The or key can then be
used to select the displayed option.
Available LCD Menus
There are two ways to select options whilst in the Programming
mode:

 




































Programming the Control Panel Veritas R8 Plus &Excel Installation Manual
20 INS045-14
The Miscellaneous Selections  - 
There are four sets of Miscellaneous Selections that control the
behaviour of various system functions.
Miscellaneous Selections Zero 
From the Programming Menu, enter .The display will show
the options currently selected.
12345678 Unset
Tamper
Zones


Press the appropriate numbered button(s) to select or de-
select the corresponding option(s) as shown on the display.
To display an explanation of the Misc. options associated with
a particular number, press and hold the corresponding key
(LCD Keypad only).
Press .The system will chime to confirm that the new
options have been accepted. The system will then automatically
revert to the Programming Menu.
Option Miscellaneous Selections Zero Default
1 Cancel Strobe with Bell Off
2 Keypad PA,
and Off
3 Single Button Setting On
4 Silent Part Set Confirmation Tone Off
5 EN50131-1 Requirements Off
6 Time Limit Engineer Access Off
7 Reset Button Cancels Setting On
8 Auto Omit AC Off
Option 1 - Cancel Bell With Strobe
When ‘ON’ the strobe will stop when the bell timer expires.
Option 2 - Keypad PA, and 
When ‘ON’ Pressing 3 and 9 together will generate a keypad PA
alarm.
Option 3 - Single Button Setting
When ‘ON’ The system can be set using the or 
keys without the need to first enter a User code.
Option 4 - Silent Part Set Confirmation Tone
When ‘ON’ a confirmation tone is generated to indicate that the
alarm has set, Will only function if Silent Part Set (see page 20) is
also selected.
Option 5 - EN 50131-1 Requirements
When ‘ON’ the following features are enabled (see page 37).
1. Reset (after an alarm) requires the use of a User code.
2. An entry alarm (defined as an entry timeout or, a Guard zone
activation during the entry period) invokes a 30 second delay
during which the communicator output and external sounder
are suppressed (i.e. the alarm response is limited to the
internal sounder(s) and external strobe for the first 30
seconds).
3. On unsetting the system the unset light will extinguish after 30
seconds.
4. On unsetting the system omitted zones are re-included.
Option 6 - Time Limit Engineer Access
When ‘ON’ the control panel will only accept Engineer codes for
the first 30 seconds after the system is unset (i.e. while the Unset
light is on if Option 5 is also selected).
Option 7 - Reset Button Cancels Exit
When ‘ON’ setting can be aborted by pressing the 
button. It is particularly useful if Single Button Setting (Option 3) is
selected but may be used independently.
Option 8 - Auto Omit AC
When ‘ON’ an AC Mains fail is automatically omitted at the time of
arming.
This option alleviates the need, for the customer to manually
omit an AC Mains Fail, fault condition.
Miscellaneous Selections One 
From the Programming Menu, enter . The display will show
the options currently selected.
12 345678Unset
Tamper
Zones


Press the appropriate numbered button(s) to select or de-
select the corresponding option(s) as shown on the display.
To display an explanation of the Misc. options associated with
a particular number, press and hold the corresponding key
(LCD Keypad only).
Press . The system will chime to confirm that the new
options have been accepted. The system will then automatically
revert to the Programming Menu.
Option Miscellaneous Selections One Default
1 Internals Only on Unset Tamper Alarm On
2 Internals Only on Part Set Zone Alarm On
3 Internals Only on Part Set Tamper Alarm On
4 Silent Part Set (no exit tone on part set) Off
5 High Level Chime (chime at full volume) Off
6 Invert Bell Output Off
7 Final Door Set Off
8 Unlock Engineer On
Option 1 - Internals Only on Unset Tamper Alarm
When ‘ON’ a tamper alarm when unset will only activate the
internal sounders.
Option 2 - Internals Only on Part Set Zone Alarm
When ‘ON’ an alarm when part set will only activate the internal
sounders.
Option 3 - Internals Only on Part Set Tamper Alarm
When ‘ON’ a tamper alarm when part set will only activate the
internal sounders.
Option 4 - Silent Part Set
When ‘ON’ no exit tones will be heard when the alarm is being part
set.
Option 5 - High Level Chime
When ‘ON’ chime tones are always full volume.
Option 6 - Invert Bell Output
When ‘ON’ the bell output will be negative removed instead of
negative applied.
Option 7 - Final Door Set
When ‘ON’ the alarm will set 3 seconds after the entry/exit door is
closed.