Texecom PREMIER 48 User manual

Issue 6
Premier 48/88/168
Quick Reference Guide
& System Records

Factory Defaults Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide
2 INS222
1. Factory Defaults
Menu Option Default
User Codes
Setup Users User 00 (Engineer) 1234
User 01 (Master) 5678
All Other Users Not Defined
1. Zone Setup
Zones Types 1 Entry/Exit 1
2 Guard Access
3 - 8 Guard
All Other Zones Not Used
Zone Areas All Zones Area A
Zone Text All Zones Not Defined
Zone Chime All Zones Silent
Remote Test All Zones Off
2. Area Programming
Timers Exit Delay - All Areas 030 Seconds
Entry Delay 1 - All Areas 045 Seconds
Entry Delay 2 - All Areas 045 Seconds
2
nd Entry Dly - All Areas 000 Seconds
Bell Delay - All Areas!000 Minutes
Bell Duration - All Areas 015 Minutes
Coms Delay - All Areas 000 Seconds
Part Bell Dly - All Areas 000 Seconds
Arming Modes All Areas!Entry/Exit
Area Arm Suites All Suites!No Areas
Area Suite Text All Suites!Not Defined
Suite Arm Modes All Suites!Timed
Area Options 1: Auto Part Arm!No Areas
2: Part Arm Instant!No Areas
3: Part Arm Silent!No Areas
4: Remote Arm All Areas
5: Remote Disarm!All Areas
6: Panel Tamper!Area A
7: Bell Tamper!Area A
8: Auxiliary Tamper!Area A
9: Panel Speaker!All Areas
10: Bell & Strobe op!All Areas
11: Alarm Eng Reset!No Areas
12: Confirmation Reset!All Areas
13: Tamper Eng Reset!All Areas **
14: Anti-code Reset!All Areas
15: Phone Line Fault!Area A
16: Arm With L/Fault!Area A
17: AC Mains Fail!Area A
18: Arm With AC Fail Area A
19: Full Arm Coms!All Areas
20: Part Arm Coms!No Areas
21: Unarm Fire Coms!No Areas
22: Unarm Tamper Coms!No Areas **
23: Auto Arm Areas!No Areas
24: Area A Foyer!No Areas
25: Log Part Omits!No Areas
26: Multi Knock Area!No Areas
27: UDL Keypad!All Areas
28: Auto Chime (C2A)!No Areas
29: Confirm In Entry!No Areas
30: Conf. After Entry!All Areas
31: Part Arm Enabled!ALL Areas
32: Bell Squawk!No Areas
33: Fob After Entry!No Areas
34: Armed = Coms !No Areas
35: 2 Wire Smoke!No Areas
36: Faults Eng Reset!All Areas **
37: L/Fault Eng Rst!All Areas **
38: AC Fail Eng Rst!No Areas
39: Anti-Masking when Armed No Areas
Area Text All Areas!Not Defined
Menu Option Default
3. Global Options
System Timers 1: Exit Settle Time 008 Seconds
2: Global Bell Dly. 000 Minutes
3: Global Bell Dur. 015 Minutes
4: Double Knock Dly 007 Seconds
5: Beam Pair Time 060 Seconds
6: Activity Delay 024 Hours
7: Abort Delay 180 Seconds
8: Courtesy Time 030 Seconds
9: Defer Arming By 030 Minutes
10: Auto Arm Delay 030 Minutes
11: Menu Time Out 180 Seconds
12: Pulse Period 1 010 Seconds
13: Pulse Period 2 020 Seconds
14: Pulse Period 3 030 Minutes
15: Line Fault Delay 000 Minutes
16: AC Off Delay 005 Minutes
17: Batt Test Period 024 Hours
18: Batt Test Time 010 Seconds
19: Soak Test Time 014 Days
20: Service Interval 000 Weeks
21: Test Call Every 000 Hours
22: Min Random Time 000 Seconds
23: Max Random Time 060 Seconds
24: Door Strike Time 005 Seconds
25: Zone Response 008x08mSec.
26: Keypad PA Delay 060 Seconds
27: Confirmation Dly 060 Minutes
28: Warning Delay 000 Minutes
29: Keypad Lock time 090 Seconds
30: Eng. Log Off Dly 060 Minutes
31: Fire Bell Delay 000 Minutes
32: Forced Entry Dly 005 Seconds
33: Supervision Time 120 Minutes
34: Poll IP Every 000 Minutes
System Config. 00: Bell on Arm Fail No Bell
01: Bell is an SCB SAB
02: Clock is 12Hr 24Hr
03: Manual BST/GMT Auto
04: Hide Armed Areas View
05: Area Bell Time Global
06: 24Hr Omit Local Global
07: Leave Omits Remove
08: Enforce Com Delay Override
09: NVM is Locked Unlocked
10: Engineer Only User + Engineer
11: Chime Visible Audible
12: Omit Tampers NO YES **
13: Offline Printing Online
14: View Act. Fault Hide
15: Hide Exit Errors Hide
16: Code Tampers Enable
17: Code Tamp Alarms Locks **
18: Areas 1-8 & I-P A-H & I-P
19: Man. Area Select Auto
20: Normal Text Predictive
21: Zone Short = Active Tamper
22: R/R=Silence/RST Reset Only
23: User Code Latch Pulse
24: Test Call = CT4 Timed
25: Batt Test = Disarm Timed
26: Bell = 2nd Alarm 1st Alarm
27: SNDR = 2nd Alarm 1st Alarm
28: Conf. = Delayed Instant
29: Abort = User Reset Eng.
30: Manual AV Output Auto

Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide Factory Defaults
INS222 3
Menu Option Default
3. Global Options Continued
Config. Options 31: Clock = Crystal 50Hz
Continued 32: 40 Column Print 80
33: Enable Text Disable
34: EN50131 Disabled Enabled
35: 1st Zone=Confirm 2nd
36: Keypads Local Global
37: Panel Grade 2 Grade 3 *
38: Enable RF FOB PA Disable
39: Mask When Armed Fault
System Options 1: Advisory Volume 6
2: Chime Volume 3
3: No. of Re-Arms 03
4: Anti-code Resets 03
5: Multi Knocks 05
6: Clock Adjustment 50 (no adjustment)
7: Quick Count 4
8: Modem Level 0
Monitor Hardware 1: Phone Line Fault Enabled
2: Power Failure Enabled
3: Aux Fuse Blown Enabled
4: Bell Tamper Enabled
5: Aux Tamper Enabled
6: Panel Lid Tamper Enabled
7: Battery Faults Enabled
Control Timers 1 – 8 Not Defined
System Text Reset Message Call Engineer to
Reset System
Anti-code Message Call ARC Centre
to Reset System
Service Message Call Alarm Co.
For Service
Location Text No Location Text
Has Been Setup
Banner Message Not Defined
Part Armed Banner * PART ARMED *
Printer Header Not Defined
Part Arm Text Part Arm 1 Evening Arm
Part Arm 2 Bedtime Arm 1
Part Arm 3 Bedtime Arm 2
Holiday Dates 1 - 8 Not Defined
Speaker Tones All Tones Enabled
PC Output Text All Text Not Defined
Custom O/P Text All Text Not Defined
4. Keypad Setup
Areas All Keypads Area A
Zone Mapping All Keypad zones Not Mapped
Options 1: PA Enabled Disabled
2: Fire Enable Disabled
3: Medical Enabled Disabled
4: Tamper Disabled Enabled
5: PA Audible Silent
6: PA Delayed Instant
7: Quick Arm Keys Off
8: Info.LED> Output Armed
Volume All Keypads 4
Sounder Options All Tones Enabled
5. Expander Setup
Areas All Expanders Area A
Text All Expanders Not Defined
Auxiliary Input All Expanders Not Used
Volume All Expanders 4
Sounder Options All Tones Enabled
Menu Option Default
6. Output Setup
Panel Outputs 1 - 5 Not Used
Digi Outputs 1 *** Tamper *
2 *** Fault Present *
3 *** AC Mains Fail *
4 *** Not Used *
5 *** Not Used *
6 *** LED Control *
7 *** Armed *
8 *** Detector Test *
Com? Channels 1 Fire
2 PA
3 Alarm
4 Armed
5 Zones Locked Out
6 Not Used
7 Confirmed Alarm
8 Abort
RedCARE Pins 1 Fire
2 PA
3 Intruder Alarm
4 Armed
5 Zones Locked Out
6 Abort
7 Confirmed Alarm
8 Not Used
Keypads 1-8 Outputs LED Control LED Control
Expanders 1-8 Outputs 1 LED Control
2 Armed
3 Detector Test
4 - 8 Not Used
Custom O/P 1 1 Control Timer 1
2 - 8 Not Used
Custom O/P 2 1 - 4 Not Used
5 Entry
6 Not Used
7 - 8 Always ON
Custom O/P 3 1 - 8 Not Used
Custom O/P 4 1 - 8 Not Used
X-10 Outputs 1 - 8 Not Used
7. UDL/Digi Options
Reset Digi N/A N/A
Test Com? N/A N/A
Set Call Waiting Number Not Defined
Program Digi ARC 1 Not Defined
ARC 2 Not Defined
ARC 3 Not Defined
Digi Options Digi is Enabled Disabled
Pulse Dialling Tone
Pulse After 3 Always Tone
Blind Dialling Wait Dial Tone
Call Waiting On Off
Dial All Numbers Dial Any
UDL Options Call Back Number 1 Not Defined
Call Back Number 2 Not Defined
Call Back Number 3 Not Defined
UDL Password Not Defined
DL Attended Unattended
Auto Call-Back Manual
Call Defeat Off On
DL Arm Limited At Anytime
Any Area Armed Fully Armed
DL Keypad not OK OK
Rings Required 005
UDL Dial Attempts 003
Area Accounts All Areas Not Defined

Factory Defaults Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide
4 INS222
Menu Option Default
7. UDL/Digi Options Continued
Setup Modules
Setup Radio-Pad ARC 1 Pri. No. Not Defined
ARC 1 Sec. No. Not Defined
ARC 1 Prefix Not Defined
ARC 2 Pri. No. Not Defined
ARC 2 Sec. No. Not Defined
ARC 2 Prefix Not Defined
ARC 3 Pri. No. Not Defined
ARC 3 Sec. No. Not Defined
ARC 3 Prefix Not Defined
Radio Pad Attempt 03
Setup AV Module? AV No.1> Not Defined
AV No. 2> Not Defined
AV No. 2> Not Defined
AV Dial Attempts 03
AV Re-Dial Delay 30 Minutes
Setup IP Data? ComIP Address Not Defined
ComIP Port 10001
ComIP Gateway Not Defined
Subnet Mask 255.255.255.0
Polling Address Not Defined
ComIP Name Not Defined
SMS Centre Pri. 07860980480
SMS Centre Sec. Not Defined
Modem Setup Stg. Not Defined
Modem Speed 2400
Com Port Setup Onboard Digi Com300
Com 1 No Module Fitted
Com 2 No Module Fitted
Expansion Port No Module Fitted
8. User Codes
Setup Users User 00 (Engineer) 1234
User 01 (Master) 5678 ****
All other Users Not Defined ****
* This options can alter the Programming as defined
below.
** These options are enabled/disabled when Config.
Option 37 is programmed as ‘Grade 2’.
*** These outputs will default to the same as the Com
Channels when Config. Option 37 is programmed as
‘Grade 2’. (see Note below)
**** All users except the engineer are defaulted to lock out
during entry.
"To quickly change the programming for the ‘Digi
Outputs’ between Grade 2 and Grade 3 without
having to manually program each output, go to
‘System Config.’ Which is in the ‘System Options’
menu and select the required Grade (option 37), then
go to ‘Default NVM’ which is in the ‘Engineer Utils’
menu, select ‘Digi Outputs’ and then press ‘YES’ to
default them.
This will only default the Digi Outputs on the control
panel, no other programming will change.

Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide Quick Reference Guide
INS222 5
2. Quick Reference Guide
!Log Off Engineer
"# Press "to log out of the Engineer Programming menu
$Zone Setup
"#Zone Types
Use $- %to enter zone number, &to edit, !- 'or (to select a
zone type, "to accept
#!Not Used (Medical
#!$Entry/Exit 1 (24Hr Gas
#!)Entry/Exit 2 (Auxiliary
#!*Guard (Tamper
#!+Guard Access (Exit Terminator
#!,24Hr Audible (Moment Key
#!-24Hr Silent (Latching Key
#!.PA Audible (Security
#!%PA Silent (Omit Key
#!'Fire (Custom
"#Zone Attributes 1 Press &to edit, $- %to select an attribute, "to accept
#$O= Omittable ,3= Part 3 Omit
#!)F= Force Omit -A= Access
#!*1= Part 1 Omit .E= Entry/Exit 2
#!+2= Part 2 Omit %G= Guard
"#Zone Attributes 2 Press &to edit, $- %to select an attribute, "to accept
#$D= Double Knock ,R= Reset
#!)B = Beam Pair -A= Auto Re-arm
#!*S= Soak Test .Q= Quick Resp.
#!+F= Activity %E= Eng. Alarm
"#Key Attributes Press &to edit, $- ,to select an attribute, "to accept
#$I= Instant Arming ,S= Silent Arming
#
(only applicable for
keyswitch zone types)!)P= Part Arming -T= Time Arm Disable
#!*F= Full Disable .K= Key Tube (Monitor Only)
#!+D= Disarm Only
"#Custom Attributes Press &to edit, $- ,to select an attribute, "to accept
#$B= Bell/Strobe +C= Enable Coms
#
(only applicable for
custom zone types)!)I=Internals ,W= Warning
#!*M= Monitor 24Hr
"Zone Areas
Press &to edit, $- %to select an area, (!= all areas, /= areas A – H and
I –P), "to accept.
"#Zone Text
Press &to edit, !- 'to select characters (press the required key the appropriate
number of times), "to accept
#$. , ? ! 1 @ “ - -M N O 6 (Move Cursor
#!)A B C 2 .P Q R S 7 0Copy Text to Memory
#!*D E F 3 %T U V 8 1Paste Text from Memory
#!+G H I 4 'W X Y Z 9 &
#!,J K L 5 !0 _
Upper, Lower Case, Predictive
Text and Numerical
"#Zone Chime Press &to alter chime tone, "to accept
&# Silent &Chime 1 &Chime 2 &Chime 3
"#Zone Mask Press &to alter Mask option, "to accept
"# Zone Wiring Press &to alter wiring type, "to acce
p
t
#!!Normally Open *Triple EOL -2K2/4K7/(6K8)
#!$# Normally Cosed +1K/1K/(3K) .4K7/4K7
#!)# Double Pole EOL ,4K7/6K8(12K) %WD Monitor

Quick Reference Guide Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide
6 INS222
)Area Programming
!Timers Use (to select an area, "to select a timer, !- 'to enter a value, "to accept
Premier 48 Premier 88 Premier 168
1:!Exit Dly for Areas: A – D (1 – 4) A – H (1 – 8) A to P (9 – 16)
2:!Entry Dly 1 for Areas: A – D (1 – 4) A – H (1 – 8) A to P (9 – 16)
3:!Entry Dly 2 for Areas: A – D (1 – 4) A – H (1 – 8) A to P (9 – 16)
4: 2nd Entry Dly for Areas: A – D (1 – 4) A – H (1 – 8) A to P (9 – 16)
5:!Bell Dly for Areas:!A – D (1 – 4) A – H (1 – 8) A to P (9 – 16)
6: Bell Duration for Areas: A – D (1 – 4) A – H (1 – 8) A to P (9 – 16)
7:!Coms Dly for Areas: A – D (1 – 4) A – H (1 – 8) A to P (9 – 16)
8:!Part Bell Dly for Areas: A – D (1 – 4) A – H (1 – 8) A to P (9 – 16)
$Use (to select an area, $- ,to select arming an mode, "to acceptArming Modes
$Entry/Exit +Instant
)Exit Term. ,Deferred
*Timed Exit
)Area Arm Suites
Use (to select a suite, &no to edit, $- %to select an area, (!= all areas, /
= areas A – H and I –P), "to accept
*#
#
Area Suite Text Use $- %to select a suite, &to edit, !- 'to select characters (press the
required key the appropriate number of times), "to accept
#$. , ? ! 1 @ “ - -M N O 6 (Move Cursor
#!)A B C 2 .P Q R S 7 0Copy Text to Memory
#!*D E F 3 %T U V 8 1Paste Text from Memory
#!+G H I 4 'W X Y Z 9 &
#!,J K L 5 !0 _
Upper, Lower Case, Predictive
Text & Numerical
+Use (to select an area, $- ,to select an arming mode, "to acceptSuite Arm Mode
$Entry/Exit +Instant
)Exit Term. ,Deferred
*Timed Exit
,Area Options
Use (to select an option, &to edit, $- %to select an area, (!= all areas,
/= areas A – H and I –P), "to accept
01:!Auto Part Arm!21: Unarm Fire Coms
02:!Part Arm Instant!22: Unarm Tamper Coms
03:!Part Arm Silent!23: Auto Arm Areas
04: Remote Arm 24: Area A Foyer!
05:!Remote Disarm!25: Log Part Omits!
06: Panel Tamper!26: Multi Knock Area
07:!Bell Tamper!27: UDL Keypad
08:!Auxiliary Tamper!28: Auto Chime (C2A)
09:!Panel Speaker!29: Confirm in Entry
10:!Bell & Strobe op!30: Conf. After Entry
11:!Alarm Eng Reset!31: Enable Part Arms
12: Confirmation Reset!32: Bell Squawk
13: Tamper Eng Reset!33: Fob After Entry
14:!Anti-code Reset!34: Armed = Coms
15: Phone Line Fault 35: 2-Wire Smoke
16:!Arm With L/Fault 36: Fault Eng Reset
17:!AC Mains Fail 37: L/Fault Eng Rst
18: Arm With AC Fail 38: AC Fail Eng Rst
19:!Area Arm Coms 39 Anti-Masking When Armed
20: Part Arm Coms
-Time Arm Areas
Use (to select an area, "to toggle between the arm and disarm timer, $- %to
select timers, "to accept
.Area Text
Use (to select an area, &to edit, !- 'to select characters (press the required
key the appropriate number of times), "to accept

Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide Quick Reference Guide
INS222 7
*Global Options
!#System Timers Use (to select a timer, !- 'to enter a value, "to accept
#01: Exit Settle Time!13: Pulse Period 2!25: Zone Response
#!02: Global Bell Dly.!14: Pulse Period 3!26: Keypad PA Delay
#!03: Global Bell Dur.!15: Line Fault Delay!27: Confirmation Dly
#!04: Double Knock Dly!16: AC Off Delay 28: Warning Delay
#05: Beam Pair Time!17: Batt Test Period 29: Keypad Lock Time
#!06: Activity Delay!18: Batt Test Time 30: Eng. Log Off Dly
#!07: Abort Delay!19: Soak Test Time 31: Fire Bell Delay
#!08: Courtesy Time!20: Service Interval 32: Forced Entry Dly
#09: Defer Arming By!21: Test Call Every 33: Supervision Time
#!10: Auto Arm Delay!22: Min Random Time 34: Poll IP Every
#!11: Menu Time Out!23: Max Random Time
#!12: Pulse Period 1!24: Door Strike Time
$#System Config.!Use (to select an option, &to change the option, "to accept
#!00: (No Bell/Bell on) Arm Fail!20: (Predictive/Normal) Text
#!01: Bell is an (SAB/SCB)!21: Zone Short=(Active/Tamper)
#!02: Clock is (12Hr/24Hr)!22: R/R=(Reset Only/Silence/RST)
#!03: (Manual/Auto) BST/GMT!23: User Codes (Pulse/Latch)
#!04: (Hide/View) Armed Areas!24: Test Call = (Timed/Timed)
#!05: (Area/Global) Bell Time!25: Batt Test = (Timed/Disarm)
#!06: 24Hr Omit (Global/Local)!26: Bell = (1st Alarm/2nd Alarm)
#!07: (Leave/Remove) Omits!27: SNDR = (1st Alarm/2nd Alarm)
#!08: Away (Override/Enforce) Delay 28: Conf. = (Instant/Delayed)
#!09: NVM is (Unlocked/Locked)!29: Abort = (Eng. Reset/User Reset)
#!10: Engineer (Only/+ User)!30: (Auto/Manual) AV Outputs
#!11: Chime (Audible/Visible)!31: Clock = (50Hz/Crystal)
#!12: Omit Tampers (NO/YES)!32: (40/80) Column Printer
#!13: (Offline/Online) Printing 33: (Enable/Disable) Text
#!14: Activity Fault (View/Hide)34: EN50131 (Disabled/Enabled)
#!15: (Hide/View) Exit Errors 35: (2nd Zone /1st Zone) = Confirm
#!16: (No/Enable) Code Tampers 36: (Global/Local) Keypads
#!17: Code Tamp (Alarms/Locks)37: Panel Grade (2/3)
#!18: Areas (1-8/A-H) & I-P 38: (Enable/Disable) RF FOB PA
#!19: (Auto/Manual) Area Select 39: Mask=(Fault/Alarm)
)#System Options!Use (to select an Option, !- 'to enter a value, "to accept
#!1: Advisory Volume!4:!Anti-code Resets 7: Quick Count
#!2: Chime Volume!5:!Multiple Knocks 8: Modem Level
#!3:!Number Of Re-Arms!6: Adjust Clock
*#Monitor Hardware!Press &to edit, (to select an option, &to change the option, "to accept
#!$P= Line Fault!+B= Bell Tamper!.B= Battery Faults
#!)A= AC Power ,A= Aux Tamper
#!*F= Aux Fuse Blown!-L= Panel Lid
+#Control Timers Use (to select an area, !- 'to enter the 1st On time, "to accept
Use $- .to select the 1st On time days of operation, "to accept
Use !- 'to enter the 1st Off time, "to accept
Use $- .to select the 1st Off time days of operation, "to accept
,#System Text Use (to select a message, !- 'to select characters (press the required key the
appropriate number of times), "to accept
-#Part Arm Text Use (to select a Part Arm, &to edit the Part Arm text, !- 'to select characters
(press the required key the appropriate number of times), "to accept
.#Holiday Dates Use (to select a holiday date, !- 'to enter the required date
(223344),"to accept
%#Speaker Tones Use (to select a tone type, &to turn the tone on/off, "to accept
'#PC Output Text Use (to select an Output, &to edit, !- 'to select characters (press the required
key the appropriate number of times), "to accept
(#Custom O/P Text Use (to select an Output, &to edit, !- 'to select characters (press the required
key the appropriate number of times), "to accept

Quick Reference Guide Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide
8 INS222
+Keypad Setup
"#Areas!Use $- %to select keypad, !to select network, &to edit, $- %to select
an area, (!= all areas, /= areas A – H and I –P), "to accept
"#Zone Ma
pp
in
g
!Press &to edit, $-%to enter zone number, "to acce
p
t, Re
p
eat for 2nd zone
"#Options!Press &to edit, (to select an option, &to change the option, "to accept
#!$P= PA Enabled!,A= PA is Audible
#!)F= Fire Enabled!-D= PA is Delayed
#!*F= Medical Enabled!.Q= Quick Arm On
#!+T= Tamper Enabled!%O= Info.LED>Output
"#Volume!Press &to edit, !- %to enter a value, "to accept
"#Sounder Options!Press &to edit, (to select an option, &to change the option, "to accept
#!$F= Fire Tones Enabled!,E= Entry Tones Enabled
#!)A= Alarm Tones Enabled!-X= Exit Tones Enabled
#!*F= Fault Tones Enabled!.C= Chime Tones Enabled
#!+S= Service Tones Enabled!%K= Use Keypad Areas
,Expander Setup
"#Areas!Use $- %to select expander, !to select network, &to edit, $- %to select
an area, (!= all areas, /= areas A – H and I –P), "to accept
"#Text!Press &to edit text, !- 'to select characters (press the required key the
appropriate number of times), "to accept
#$. , ? ! 1 @ “ - -M N O 6 (Move Cursor
#!)A B C 2 .P Q R S 7 0Copy Text to Memory
#!*D E F 3 %T U V 8 1Paste Text from Memory
#!+G H I 4 'W X Y Z 9 &
#!,J K L 5 !0 _
Upper, Lower Case, Predictive
Text & Numerical
"#Auxiliary Input!Press &to edit, !- .to select an input type, "to accept
#!!Not Used!-Silence Sounders
#!$Auxiliary Tamper!.Global Omit Key
#!)Bell Tamper!%Local Omit Key
#!*Remote Reset!'PSU Monitor
#!+Line Fault +ve!(Defer Auto Arming
#!,Line Fault -ve
"#Volume!Press &to edit, !- %to enter a value, "to accept
"#Sounder Options!Press &to edit, (to select an option, &to change the option, "to accept
#!$F= Fire Tones Enabled!,E= Entry Tones Enabled
#!)A= Alarm Tones Enabled!-X= Exit Tones Enabled
#!*F= Fault Tones Enabled!.C= Chime Tones Enabled
#!+S= Service Tones Enabled!
-System Outputs
!#Panel Outputs!
$#Digi Outputs
)#Com? Channels
*#RedCARE Pins
Use $- %to select an output, &to edit, $- .to enter an output group,
!- 'to enter output type, "to accept
+#Keypad Outputs
,#Expander Outputs
Use $- %to select device, !to select network, (to select an output, &to
edit, $- .to enter an output group, !- 'to enter output type, "to accept
-#Custom Outputs Use !to select output, $- %to select a switch, &to edit, $- .to enter an
output group, !- 'to enter output type, "to accept
.#X-10 Outputs Use $- %to select an output, &to edit, $- .to enter an output group,
!- 'to enter output type, !- 'to enter House/device Number, "to accept

Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide Quick Reference Guide
INS222 9
Key Output Group Outputs Types
!#Not Used: Press "to accept
$#System:!Use !- 'to enter an output type or use (to search, "to accept
#!00: Phone Line Fault 18: UDL Lockout!35: Custom 4 Stage A
#01: Mains Power Off 19: UDL Call Active!36: Custom 4 Stage B
#02: Aux Fuse Fault 20: UDL Enabled 37: Custom 4 Stage AB
#03: Auxiliary Tamper 21: Confirmed Alarm 38: Com 1 Fault
#04: Bell Tamper 22: Custom 1 Stage A 39: Com 2 Fault
#05: Panel Lid Tamper 23: Custom 1 Stage B 40: Com 1 No Signal
#!06: Engineer Working 24: Custom 1 Stage AB 41:!Com 2 No Signal
#!07: Confirm Devices 25: Custom 2 Stage A 42: Coms Fault
#!08: Service Required 26: Custom 2 Stage B 43: Radio Jamming
#!09: Bell Fuse Blown 27: Custom 2 Stage AB 46:!Radio RX Tamper
#!10: Battery Fault!28: Radio-Pad Failed 47: Detector Test
#!11: Battery Test On!30: No Radio Signal 48: ATS Remote Test
#!12: Courtesy Light!31: Radio-Pad Lost 49: Dual Path Fault
#!13: System Open!30: No Radio Signal 50: CIE Fault
#!14: Fully Arm!31: Radio-Pad Lost 51: PSU Fuse Blown
#!15: Digi Failed!32: Custom 3 Stage A 52: PSU Battery Flt
#!16: Digi Successful!33: Custom 3 Stage B 53: WD Test Active
#!17: Digi Active!34: Custom 3 Stage AB
)#Area: Use !- 'to enter an output type or use (to search, $- %to select an area,
(!= all areas, /= areas A – H and I –P), "to accept
#00: Intruder Alarm 23: Part Armed!46: Time Arming
#01: Guard 1 Alarm 24: Part Arming!47: 1st Code Entered
#02: Guard 2 Alarm 25: Force Arm!48: 2nd Code Entered
#03: Entry Alarm 26: Force Arming!49: Area Secured
#04: Confirmed Alarm 27: Arm Fail!50: Part Armed 1
#05: 24Hr Audible 28: Bell SAB!51: Part Armed 2
#06: 24Hr Silent 29: Bell SCB!52: Part Armed 3
#07: 24Hr Gas 30: Strobe!53: Custom Alarm
#!08: PA Audible 31: Switch 12 Volts!54: Zone Warning
#09: PA Silent 32: Detector Reset!55: Arm Fail Warning
#10: Duress 33: Walk Test Active!56: Forced Entry
#11: Fire Alarm!34: Zones Omitted 57: Zones Locked Out
#12: Medical 35: 24Hr Zones Omit 58: All Armed
#13: Auxiliary Alarm!36: Reset Required 59: Auto Arm Disable
#14: Tamper Alarm!37: Door Strike 60: Armed / Alarm
#15: Alarm Abort!38: Chime Mimic 61: Intruder Alarm
#16: Ready!39: Chime Enabled 62: Speaker Mimic
#17: Entry Mode!40: DK First Knock 63: Full Arm/Exit
#18: 2nd Entry Mode!41: BP First Knock 64: Detector Fault
#19: Exit Mode!42: On Test 65: Detector Mask
#20: Entry/Exit Mode!43: Test Fail 66: Fault Present
#21: Armed!44: Internal Alarm 67: LED Control
#22: Full Arm!45: Auto Arming 68: Full Armed Entry
*#Zone: Use $- %to enter a zone number or use (to search, !- ,to select a zone
output type, "to accept
#$Mimic *Alarm ,MimicLatch
#)MimicArm +Tamper!-Omitted
+#User: Use $- %to select a User code or use (to search, "to accept
,#Control Timer: Use $- %to select a Control Timer, "to accept
-#PC Control: Use $- %to select a PC Control, "to accept
.#Door Control: Use $- %to select a Door Control, "to accept
%#X-10: Use $- %to select a an X-10 Output, "to accept

Quick Reference Guide Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide
10 INS222
Key Attributes Attribute Types
"#Attributes!Press "to edit, $- %to select attributes, "to accept
#$U= User Test ,2= Use Pulse Timer 2
#)I= Inverted -3= Use Pulse Timer 3
#*L= Latching .C= Custom Output 1, Stage A
#+1= Use Pulse Timer 1 !%R= Random
.UDL/Digi Options
!#Reset Digi Press "to reset communicator
$#Test Com? Press "to send test call to the ARC, $- *to initiate a call to the remote UDL
computer (using Call Back numbers 1, 2 or 3)
)#Set Call Waiting Press &to edit, enter call waiting number, "to accept
#!- '= Numbers 0 to 9 0Insert a ‘#’
#&then "= Clear Screen 1,(3 Second pause)
#5Insert a ‘*’/W (10 Second pause)
*#Program Digi Use (to select ARC sets 1 - 3, &to edit
#Protocol Press &to edit, !- +to select protocol, "to accept
#!Disabled )Contact ID +EasyCom Pager
#$Fast Format *SIA Level II ,SMS
#Telephone Number 1 Press &to edit, !- 'to enter telephone number, "to accept
#Telephone Number 2 Press &to edit, !- 'to enter number, "to accept
#Account Number Press &to edit, !- 'to enter number, "to accept
#Dialling Attempts Press &to edit, !- 'to enter number, "to accept
#Reporting Channels Press &to edit, $- %to select channels, "to accept
(only available for Fast Format)
#Restoring Channels Press &to edit, $- %to select channels, "to accept
(only available for Fast Format)
#Open/Close Channels Press &to edit, $- %to select channels, "to accept
(only available for Fast Format)
#Reporting Areas#Press &to edit, $- %to select an area, (!= all areas, /= areas A – H
and I –P), "to accept (only available for Contact ID, SIA Level II, EasyCom Pager and
SMS Messaging)
#Reporting Options Press &to edit, $- %to select option, "to accept
(only available for Contact ID, SIA Level II, EasyCom Pager and SMS Messaging)
#$P= Priority Alarms ,M= Maintenance
#)A= Normal Alarms -T= Tamper Alarms
#*C= Open/Close .C= Test Calls
#+O= Omits & Reinstates %R= Restores
#Config. Press &to edit, $- %to select option, "to accept
(only available for Contact ID, SIA Level II, EasyCom Pager & SMS Messaging)
#$A= Use Area Acc ,A= Activate AV
#)S= Use SIA I -F= Use GSM First
#*R= Enable RadioPad .I= Connect Via IP
#+G= Enable GSM
+#Digi Options Press &to edit, (to select an option, &to change the option, "to accept
#$E= Digi is Enabled +B= Blind Dialling
#)P= Pulse Dialling ,W= Call Waiting On
#*3= Pulse after 3 -A= Dial All Numbers

Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide Quick Reference Guide
INS222 11
.UDL/Digi Options Continued
,#UDL Options Press &to edit Call Back number 1, enter the number, "to accept
#!- '= Numbers 0 to 9 0Insert a ‘#’
#&then "=Clear Screen 1
,
(
3 Second
p
ause
)
#5Insert a ‘*’/W (10 Second pause)
#Call Back Number 2 Press &to edit Call Back number 2, enter the number, "to accept
#Call Back Number 3 Press &to edit Call Back number 3, enter the number, "to accept
#UDL Password Press &to edit, !- 'to enter number, "to accept
#UDL options Press &to edit, (to select an option, &to change option, "to accept
#$A= DL Attended +L= Armed DL Limited
#)M= Manual Call-back ,A= Any Area Armed
#*D= Call Defeat On -K= Online RKP = Off)
#Number of Rings Press &to edit, !- 'to enter number of rings, "to accept
#Dialling Attempts Press &to edit, !- 'to enter number of dialling attempts, "to accept
-#Area Accounts Use (to select an area, &to edit, !- 'to enter account number, "to accept
.#Setup Modules Press 6to reset communicator
#Setup Radio-Pad? Press "to set-up Radio-Pad, 7to exit
#Pad ARC 1 Pri No Press &to edit, !- 'to enter telephone number, "to accept
#Pad ARC 1 Sec No Press &to edit, !- 'to enter telephone number, "to accept
#Pad ARC 1 Prefix Press &to edit, !- 'to enter pad prefix, "to accept
#Pad ARC 2 Pri No Press &to edit, !- 'to enter telephone number, "to accept
#Pad ARC 2 Sec No Press &to edit, !- 'to enter telephone number, "to accept
#Pad ARC 2 Prefix Press &to edit, !- 'to enter pad prefix, "to accept
#Pad ARC 3 Pri No Press &to edit, !- 'to enter telephone number, "to accept
#Pad ARC 3 Sec No Press &to edit, !- 'to enter telephone number, "to accept
#Pad ARC 3 Prefix Press &to edit, !- 'to enter pad prefix, "to accept
#
#Setup AV Module? Press "to set-up AV Module, 7to exit
#AV No.1 Press &to edit, !- 'to enter telephone number, "to accept
#AV No.2 Press &to edit, !- 'to enter telephone number, "to accept
#AV No.3 Press &to edit, !- 'to enter telephone number, "to accept
#AV Dial Attempts Press &to edit, !- 'to enter number of dialling attempts, "to accept
#AV Re-Dial Delay Press &to edit, !- 'to enter the re-dial delay, "to accept
#
#Setup IP Module? Press "to set-up IP Module, 7to exit
#ComIP Address Press &to edit, !- 'to enter an IP Address, "to accept
#ComIP Port Press &to edit, !- 'to enter a Port Number, "to accept
#ComIP Gateway Press &to edit, !- 'to enter a Gateway Address, "to accept
#ComIP Mask Press &to edit, !- 'to enter a Subnet Mask, "to accept
#Polling Address Press &to edit, !- 'to an IP Address, "to accept
#ComIP Name Press &to edit, !- 'to a Name, "to accept
#
#SMS Centre Pri Press &to edit, !- 'to enter telephone number, "to accept
#SMS Centre Sec Press &to edit, !- 'to enter telephone number, "to accept
#Modem Setup Stg. Press &to edit, !- 'to enter modem string, "to accept
#Modem Speed Press &to edit, !- 'to enter telephone number, "to accept
#Pad ESN View only
#Pad NUA View only
#Forward Signal View only
#Reverse Signal View only
#Bit Error Rate View only
#Cyclic Redundancy View only
#GSM Signal/BER View only
#Com1 Press 6to reset com port
#Com2 Press 6to reset com port

Quick Reference Guide Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide
12 INS222
.UDL/Digi Options Continued
%Use !- *to select a com port, &to edit, (to select an option, "to accept
#
Com Port Setup
!Nothing Fitted ,Modem Unit (RadioPlus
#Onboard Digi Port $Com300 -Radio-pad (Inovonics Radio
#Com Ports 1 & 2 )Com2400 .GSM Module (WebWayOne Module
#*ComISDN %Crestron System (X-10 Control
#+ComIP 'SIP (IRIS IP Module
#Expansion Port !Nothing Fitted )ID Module
#$AV Module *X10 Module
%Setup Users
"Select User Use !- 'to enter enter a user number, 6to Delete User, 5to assign a Radio
FOB, 0to Copy a TAG, 1to Import a TAG, "to enter a Code
"User Code Use !- 'to enter a code, "to accept
"User Areas Use $- %to select an area, (!= all areas, /= areas A – H and I –P), "to accept
"User Types Use !- 'to select a user type, "to accept
$Master ,Arm Only 'Custom
)Manager -Duress !Engineer
*Standard .Door Strike
+Local %Vacation
"Press &to edit, (to select an option, &to change option, "to accept
#$A= Arming +R= Eng. Reset .Y= Auto ‘YES’
#
User Options 1
)D= Disarming ,a= Local Arming %D= Disarm First
#*O= Omitting -d= Local Disarming
"Press &to edit, (to select an option, &to change option, "to accept
#$U= User Menu +V= Vacation .C= Duress Code
#
User Options 2
(only available to
Custom users) )E= Eng. Program ,S= Door strike %O= Open/Close
#*D= Dual Code -R= Call Rem. PC
"#Press &to edit, (to select an option, &to change option, "to accept
#$C= Change Code +S= System tests .A= Add Eng. Code
#)Z= Chime Zones ,U= Setup Users %N= NVM Locking
#
User Config.
(only available to
Custom users with
User Menu) *T= Change Timer -E= Eng. Access
"#User Time Lock Use $- %to select a control timer, "to accept
"#User Text Press &to edit, !- 'to select characters (press the required key the appropriate
number of times), "to accept
#$. , ? ! 1 @ “ - -M N O 6 (Move Cursor
#!)A B C 2 .P Q R S 7 0Copy Text to Memory
#!*D E F 3 %T U V 8 1Paste Text from Memory
#!+G H I 4 'W X Y Z 9 &
#!,J K L 5 !0 _
Upper, Lower Case,
Predictive Text & Numerical
"Use $- %to select a door, !to select network "to accept
#$Door 1 +Door 4 .Door 7
#)Door 2 ,Door 5 %Door 8
#
Door Control
(only available to
Users with Door
Strike attribute) *Door 3 -Door 6 !Select Network
"Assign Prox TAG Press "to assign TAG, present TAG to ‘Prox’ symbol on keypad

Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide Quick Reference Guide
INS222 13
'Engineer Utils
!# View System Log "to view System, Alarm or Mandatory log
Use (to move up and down through log (down moves back in time, up moves forward again),
/to show area information or time and date, $- .or 0to find specific events
(Move backwards and forwards +View Omits/Reinstate Events
/View Area/Time and date ,View Maintenance Events
$View Priority Alarms -View Tamper Alarms
)View Normal Alarms .View Test Call Events
$#
)#
*#
#
System log
Alarm Log
Mandatory Log
*View Open/Close Events 0View Matching Events
$# Do Bell Test Use (to select an option, use $- %or "to activate outputs
#1: Test Bell 6: Test RedCARE
#2: Test Strobe 7: Fast
#3: Test Speaker 8: LCD Display
#4: Test Digi 9: User Outputs
#5: Test Panel
)#Do Walk Test Press /to display zones that have been tested/still need testing, 0to make zones
Chime every time they are activated.
*#View Zone Status Use !- 'to enter zone number or use (to search, 0to walk test selected
zone, 5to omit zone temporarily
+#System Tests Use $- +to select an option or use (to search, "to accept
#$View Sys. Status *Test Outputs (see Do Bell Test)
#)View Batt Status +View Version No.
,#Confirm Devices Use (to select network, "to confirm Devices, /to view error count, 6to reset
error count
-#Check RKP Status Use $- %to select keypad, !to select network, /to display errors/tamper, &
to test output, 5to test sounder,
.#Check Exp. Status Use $- %to select expander, !to select network, /to display
zones/voltage/outputs/errors, 0to test zones, 5to test sounder,
$- %to test outputs
%#Set System Time Use !- 'to enter time (24-hour format) 8833, "to accept
'#Set System Date Use !- 'to enter date 223344, "to accept
(#Location Text Press "to view Location Text
(#Print Log Use $- %to enter number of events to be printed, "to print log
(#Start Soak Test Use $- %to select an area, (!= all areas, /= areas A – H and I –P), "to
accept, "to start test
(#Change Eng.Code Use !- 'to enter a code, "to accept
(#Adjust Volumes Use (to select Panel, Keypad or Expander speakers. Press &to edit, !- %to
enter a value, "to accept
(#Default NVM Data Press $- %to select an option or (to search, "to default
#00: Panel Outputs 09: Remote Options
#01: Digi Outputs 10: User Codes
#02: Expander Outputs 11: System Timers
#03: Keypad Outputs 12: System Options
#04: Com???? Channels 13: Area Options
#05: RedCARE Pins 14: System Text
#06: Zone Types 15: UDL Options
#07: Zone Text 16: Digi Options
#08: Expander Options
(#View iD Data Use !to select loop, /to select normal scan, quick scan or biscuit mapping. Use
(to select biscuit, &to edit, !- 'to enter zone number, "to accept
(#Configure Radio Use $- %to select a device, "to learn device, &to map zone, $- %to
enter zone number, "accept
1Alter Part Arms
#Press !- 'to enter zone number or use (to search, 5, 0or 1to select Part Arms 1, 2 or 3
#5Part Arm 1 0Part Arm 2 1Part Arm 3

Notes Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide
14 INS222

Premier 48, 88 & 168 Factory Defaults and Quick Reference Guide Quick Reference Guide
INS222 15

Texecom Limited, Bradwood Court, St. Crispin Way, Haslingden, Lancashire BB4 4PW,
England.
Technical Support:
UK Customers Tel: [phone]
(Calls charged at 3.36 pence per minute from a BT landline. Calls from other networks may vary.)
International Customers Tel: [phone]
Email: [email protected]
© Texecom Limited 2007
INS222-6