Texecom Veritas R8Plus User manual

o400
MASTER USER GUIDE
For Service Call Scorpion Group Security - 01452 525397
THANK YOU FOR VOTING TEXECOM

Assigning Access Codes Master User Guide
2 INS140-2
Master User Guide
Assigning Access Codes
The control panel allows up to eight users to operate the alarm system,
each user is assigned an “Access code”, “Access Level” and “User
Number”. The figure below shows an example of users assigned to
a typical alarm system:
User Number
Each user is identified by the alarm system as User 1 through to User 8.
Access Code
Each user has a programmable 4 digit Personal Access code which the
user enters in order to operate the alarm system.
Access Level
Each user has a programmable Access Level that determines how the
alarm system responds and which of the system facilities the user can
access.
Each Access Level has an associated number (1 – 8) which is used
when programming the Access Level of a user.
User Number:1
A
ccess Code:
A
ccess Level:
Access Type:
4321
Boss Engineer
Installer
1
User Number:2
A
ccess Code:
A
ccess Level:
Access Type:
????
Master User
Customer
2
User Number:3
A
ccess Code:
A
ccess Level:
Access Type:
5678
User
Customer
3
User Number:8
A
ccess Code:
A
ccess Level:
Access Type:
2580
Cleaner
Customer
8
4...7

Master User Guide Assigning Access Codes
INS140-2 3
There are eight possible User Access Levels:
User !
A User may set, unset, silence an alarm and reset the system. In
addition a User can test the system outputs, perform a walk test and
view the event log. A User cannot change Access codes (other than
their own) or Access Levels.
Engineer "
Engineers cannot change Access Levels or Access codes (other than
their own). However they can access all system programming options.
Personal Attack #
Entering a PA code will cause an immediate alarm, sounding both the
internal and external sounders.
Duress $
A Duress code behaves exactly as a User code (Level 1) but will in
addition activate the Duress channel on the communicator interface to
secretly summon assistance.
Master User %
A Master User may set, unset, silence an alarm and reset the system. In
addition a Master can test the system outputs, perform a walk test and
view the event log. A Master User can also assign new user Access
code and Access Levels.
Cleaner &
If the system is full set or part set then a Cleaner code will automatically
omit the Cleaner Suite zones without affecting the other zones. In
addition pressing a key will NOT cause the system to start entry mode.
On leaving, the cleaner should enter their Access code '''' and
press either (or ). The *key is disabled and the previous
set will be restored irrespective of which key was pressed. A cleaner
cannot access Chime. Nor can they cancel an alarm or reset the
system.

Assigning Access Codes Master User Guide
4 INS140-2
1. When a cleaner is Setting the system the Cleaner Suite zones
will flash indicating that they are currently omitted but are about
to be re-included. Any other omitted zones (e.g. if the system
was previously part set rather than full set) will also flash but will
NOT be included.
2. If the system is unset then a cleaner can full set, part set and
omit zones.
Null +
The Null level is the only level which can be changed both by a Master
User and by a Boss Engineer. The Null level has two functions:
1. If a user is no longer required, its Access Level should be
changed to Null. This will erase the associated Access code.
2. To change a Customer Access Type to an Installer Access Type,
or vice versa, it must first be changed to the Null level.
Boss Engineer ,
Boss Engineers cannot change Customer Access Levels or Customer
Access codes. They can only change Installer Access Levels and
Installer Access codes. Boss Engineers can also access all system
programming options.
Access Type
There are two Access Types, Customer and Installer. The Boss Engineer
level can only program the Installer Types. The Master User Level can
only program the Customer Types.
The table below shows a summary of each Access Level and who is
responsible for assigning the level:
Access Level Access Level
Number Access Type Can be Programmed by
User !Customer Master $#"!
Engineer "Installer Boss ''''
PA (Panic) #Customer Master $#"!
Duress $Customer Master $#"!
Master User %Customer Master $#"!
Cleaner &Customer Master $#"!
Null +Customer
Installer
Master $#"!
Boss ''''
Boss Engineer ,Installer Boss ''''
!

Master User Guide Programming Access Codes
INS140-2 5
Programming Access Codes
Each user has a programmable 4 digit Access code which the user
enters in order to operate the alarm system.
Changing Your Own Access Code &-
Every user has the ability to change their own 4 digit Access code, as
follows:
From the Unset State:
1) Enter your existing Access code ''''
2) Press PROG to access the Programming Menu .
3) Enter 60 to select the Change Your Access code option &-
4) Enter your new 4 digit Access Code ''''
5) Press PROG, the system will chime to confirm your new code .
6) Press RESET to revert to the unset state /
Assigning a New Access Code &! – &,
The Master User can assign a new Access code or change an existing
Access code providing it is a Customer Type. The Boss Engineer can
assign a new Access code or change an existing Access code providing
it is a Installer Type.
From the Unset State:
1) Enter your Access code (Master User or Boss Engineer only) ''''
2) Press PROG to access the Programming Menu .
3) Enter 6 to select the Change Access code option &
4) Enter the User Number (1 - 8) you wish to change, e.g. 5 %
5) Enter their new 4 digit Access code ''''
6) Press PROG, the system will chime to confirm the new code .
7) Press RESET to revert to the unset state /
Displaying Your User Number &0
Each user is identified by the alarm system as User 1 through to User 8.
Every user may view their User Number (1 - 8) as follows:

Programming Access Codes Master User Guide
6 INS140-2
From the Unset State:
1) Enter your Access code ''''
2) Press PROG to access the Programming Menu .
3) Enter 69 to select the View Your User Number option &0
4) The zone light corresponding to your User Number will illuminate
5) Press RESET, the system will return to the Programming Menu /
6) Press RESET to revert to the unset state /
Changing Access Levels +! –+,
Each Access Level has an associated Number (1 –8) as follows:
Access Level Access Level
Number Access Type Can be Programmed by
User !Customer Master $#"!
Engineer "Installer Boss ''''
PA (Panic) #Customer Master $#"!
Duress $Customer Master $#"!
Master User %Customer Master $#"!
Cleaner &Customer Master $#"!
Null +Customer
Installer
Master $#"!
Boss ''''
Boss Engineer ,Installer Boss ''''
The Master User can only assign Customer Access Types and the
Boss Engineer can only assign Installer Access Type.
From the Unset State:
1) Enter your Access code (Master User or Boss Engineer only) ''''
2) Press PROG to access the Programming Menu .
3) Enter 7 to select the Change Access Level option +
4) Enter the User Number (1 - 8) you wish to change, e.g. 5 %
5) Enter their new Access Level (1 - 8) e.g. 4 = Duress $
6) Press PROG, the system will chime to confirm the new Access Level .
7) Press RESET to revert to the unset state /
!

Master User Guide Programming Access Codes
INS140-2 7
Displaying Your Access Level +0
Every user may view their own Access Level
From the Unset State:
1) Enter your Access code ''''
2) Press PROG to access the Programming Menu .
3) Enter 79 to select the View Your Access Level option +0
4) The zone light corresponding to your Access Level will illuminate
5) Press RESET, the system will return to the Programming Menu /
6) Press RESET to revert to the unset state /
For security reasons the Duress Access Level will be displayed as
the User Access Level.
Noteswww.scorpion-group.co.uk
!

Code Table Master User Guide
INS140-2 For Service Call Scorpion Group Security - 01452 525397 - www.scorpion-group.co.uk
Code Table
User
No. User Name
Default
Access
Code
Option to
Change
Access
Code
New
Access
Code
Default
Access
Level
Option to
Change
Access
Level
New
Access
Level
1$#"! &! %Master +!
2'''' &" ,Boss +"
3N/A &# +Null +#
4N/A &$ +Null +$
5N/A &% +Null +%
6N/A && +Null +&
7N/A &+ +Null ++
8N/A &, +Null +,
1. Customer codes can only be programmed when the
Programming Menu is accessed using a Master User code.
2. Installer codes can only be programmed when the
Programming Menu is accessed using a Boss Engineer code.
Access Level Access Level
Number Can be Programmed by
User !Master $#"!
Engineer "Boss ''''
PA #Master $#"!
Duress $Master $#"!
Master User %Master $#"!
Cleaner &Master $#"!
Null +Master $#"!
Boss ''''
Boss Engineer ,Boss ''''
!