The Container Store Linea Leaning Desk User manual

Thank you for purchasing the Leaning Desk. The next two pages list all of the contents included in the box. Please take the time to
identify the hardware as well as the individual components of this product. As you unpack and prepare for assembly, place the contents
on a carpeted or padded area to protect them from damage.
Assembly Instructions
Linea Leaning Desk

Hardware
WARNING: Severe injury may occur if furniture tips over. Never allow children to climb or play on this product. Place heavier
items on lower shelves as far back as possible and never overload. Follow all instructions listed in this assembly guide and always
use the anti-tip hardware to mount unit to a wall.
Anti-Tip Hardware
Tools:
You may choose to use a mallet/hammer to tap dowels in. A screwdriver and drill will be required to complete assembly of the anti-tip strap.
(H6) x 2
allen wrench
(H1) x 4+1 extra
long dowel
(H15) x 1
panhead screw
(H8) x 6+1 extra
1” panhead screw
(H7) x 4+1 extra
1/2” panhead screw
(H10) x 4+1 extra
flathead screw
(H13) x 1
38mm wall screw
(H14) x 1
wall anchor
(H16) x 1
wall strap
(H5) x 4+1 extra
short dowel
(H2) x 4+1 extra
short bolt
(H4) x 2+1 extra
long bolt
(H3) x 2+1 extra
binding screw
(H9) x 2
mending plate
(H11) x 1
left bracket
(H12) x 1
right bracket
PAGE 2 OF 10PARTS LIST

Item Description Quantity
A
B
C
D
E
F
G
1
1
1
1
1
1
1
Right side upper leg
Right side lower leg
Left side upper leg
Left side lower leg
Top Shelf
Second Shelf
Bottom Shelf
G
F
E
A
B
C
D
PAGE 3 OF 10
PARTS LIST

step 1.
1. Use two long dowels to assemble each leg.
2. Make sure the dowels are fully inserted.
C
D
A
B
(H1) x 4
long dowel
PAGE 4 OF 10

step 2.
1. Fasten Bottom Shelf [G] to the Leg Assembly [CD] using a long bolt and a binding screw.
2. Each remaining shelf is attached using a short bolt and a short dowel.
E
F
G
D
C
(H2)
(H5)
(H4)
(H3)
(H6) x 2
allen wrench
(H5) x 2
short dowel
(H2) x 2
short bolt
(H4) x 1
long bolt
(H3) x 1
binding screw
PAGE 5 OF 10

step 3.
1. Fasten right leg assembly [AB] to Bottom Shelf [G] using a long bolt and binding screw.
2. Use the short bolts and short dowels to fasten the right leg assembly to the remaining shelves.
A
(H2)
(H4)
(H5)
(H3)
B
(H5) x 2
short dowel
(H2) x 2
short bolt
(H4) x 1
long bolt
(H3) x 1
binding screw
PAGE 6 OF 10

step 4.
1. Fasten each Bracket [H11 & H 12] to the Bottom Shelf [G] using two 1/2” panhead screws [H7].
2. Fasten each Bracket [H11 & H 12] to the Legs using three 1” panhead screws [H8].
(H8) x 6
1” panhead screw
(H7) x 4
1/2” panhead screw
(H11) x 1
left bracket
(H12) x 1
right bracket
(H8)
(H7)
(H7)
(H8)
PAGE 7 OF 10

step 5.
(H10) x 4
flathead screw
(H9) x 2
mending plate
1. Locate pilot holes on the backs of the legs.
2. Use the small flathead screws to attach the mending plates.
If you have purchased multiple leaning bookcases or desks,
use the mending plates to connect multiple units together.
PAGE 8 OF 10

step 6.
(H15) x 1
panhead screw
(H13) x 1
38mm wall screw
(H14) x 1
wall anchor
(H16) x 1
wall strap
This product must always be mounted to a wall. It is essential to use wall anchors appropriate to your wall type (e.g. plaster, drywall,
etc). If you are unsure about your wall type or which mounting method you should use, consult a qualified professional. Mount to wood
studs whenever possible.
Position the unit against
the wall in the desired location.
Locate the pilot hole and
attach the wall strap to the
back of the shelf with the
pan head screw.
Gently pull the wall strap along
the product so that the strap
will be hidden from view and
mark the position of the strap
hole on the wall.
Drill a 1/4” hole.
Tap in wall anchor.
Fasten anti-tip strap
with wall screw provided.
12
3
4
5
6
PAGE 9 OF 10

Do not exceed the recommended weight limits on the designated panels. Exceeding
these limits could cause sagging, possibly resulting in failure of the panel or bodily injury.
50 pounds each
75 pounds each
PAGE 10 OF 10