The world models manufacturing 1/4 super cub User manual

A036PO30501409

INSTRUCTION MANUAL

1/4 SUPER CUB

(A036)

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY (ARF) SERIES

MADE IN CHINA

Wing Span

Wing Area

Flying Weight

Fuselage Length

104in / 2640mm

1586sq in / 102.3sq dm

14 lbs / 6300g

68 in / 1725mm

Warning ! This model is not a toy.

It is designed for maximum performance. Please seek advice if one is not familiar with this kind

of engine powered precision model. Operating this model without prior preparation may cause

injuries. Remember, safety is the most important thing. Always keep this instruction manual at

hand for quick reference.

* Specifications are subject to change without notice.*

Specifications

Requires:2 stroke 0 or 4 stroke engine,

5-channel radio w 6 standard servos

- 91 - 1 20-1 60 . . .

All manuals and user guides at all-guides.com

all-guides.com

A036PO30501409

P. 3 -13

Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT

and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you

find to be defective after the gluing process may be difficult to remove for warranty replacement. The

manufacturer will replace any defective parts, but will not extend to the parts that are good before

gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.

INDEX

BEFORE YOU BEGIN

PARTS LIST

ASSEMBLY

SAFETY PRECAUTIONS

P. 1

P. 2

P.13

BEFORE YOU BEGIN

Read through the manual before you begin, so you will have an overall idea of what to do.

Symbols used throughout this instruction manual comprise of the following : -

P.1

3mm

Do not overlook this symbol!

Cut off shaded portion.

Peel off shaded portion

covering film.

Pay close attention here!

Pierce the shaded portion

covering film.

Must be purchased separately!

Drill holes with the specified

diameter (here: 3mm).

Ensure smooth non-binding

movement while assembling.

Apply instant glue

(C.A.glue, super glue.)

Assemble left and right

sides the same way.

Apply epoxy glue.

Apply thread locker

Warning!

1/4 SUPER CUB

All manuals and user guides at all-guides.com

A036PO30501409

P.2

Parts List

COVERING:--

TOUGHLON STL 100 WHITE

TOUGHLON STL 312 BRIGHT RED

1.MAIN WING -- 1 pair

2.PUSHROD Ø1.8x120mm

w/ Threads(For Aileron & Flap Servo) -- 4 pcs

FUEL TUBE Ø6x5mm -- 8 pcs

STRAPER PL4112102 -- 4 pcs

SCREW PB 2x30mm -- 12 pcs

SCREW PWA2x8mm -- 16 pcs

SERVO MOUNTING PANEL--4 pcs

CLEVIS PL4112103-- 4 pcs

TRI-HORN M3x22mm(L) PL4111251 -- 4 sets

3.SCREW PM3x15mm -- 12 pcs

WASHER d3xD7mm -- 16 pcs

M3 NUT -- 4 pcs

MAIN WING STRUTS -- 1 set

WING STRUT WIRE Ø3x143x208mm -- 2 pcs

PLASTIC WIRE BRACKET PL5330030 -- 8 pcs

4.FUSELAGE -- 1 pc.

STABILZER & ELEVATOR -- 1 set

5.VERTICAL FIN & RUDDER -- 1 set

6.TAIL GEAR ASSEMBLY 11-22LBS PL3410021 -- 1 set

PLATE(For Staying on Tail Fuselage Bottom) 1x10x40mm -- 1 pc

7.SCREW PM3x13mm -- 2 pcs

ALUMINUM PLATE 2mm -- 2 pcs

MAIN LANDING GEAR -- 1 set

SCREW PA3x12mm -- 14 pcs

WASHER d3xD7mm -- 2 pcs

MOUNTING PLATE 12x20mm -- 6 pcs

8.SCREW PA 1.7x8mm -- 6 pcs

SCREW PM3x13mm -- 8 pcs

WASHER d3xD7mm -- 16 pcs

M3 NUT -- 8 pcs

COLLAR Ø4.6mm w/ set screw -- 4 sets

MAIN WHEEL(CUB) Ø107mm -- 2 sets

PLYWOOD 3x145x171mm(Main Landing Gear Cover) -- 2 pcs

PLASTIC WIRE BRACKET PL5330050 -- 8 pcs

9.ENGINE MOUNT PL5111080 -- 1 set

SOCKET HEAD SCREW M4x30mm -- 4 pcs

WASHER d4.2xD14.5mm -- 4 pcs

M4 BLIND NUT -- 4 pcs

10.ALUMINUM PLATE(For Engine Mount) -- 1 pc.

ANTI-VIBRATION MOUNT PL5214094 -- 1 set

INCLUDE:SOCKET HEAD SCREW M4x35mm -- 4 pcs

SCERW KM3x20mm -- 8 pcs

WASHER d4xD12mm -- 8 pcs

NYLON INSERT LOCK NUT M3 -- 8 pcs

NYLON INSERT LOCK NUT M4 – 4 pcs

THROTTLE PUSHWIRE Ø1.2x480mm -- 1 pc.

PLASTIC TUBE d2xD3x300mm -- 1 pc.

11.SCREW PWA2.6x12mm -- 4 pcs

SILICON GROMMET d1.5xD6.5mm(For Cowling) -- 4 pcs

COWLING -- 1 pc.

12.FUEL TANK 450cc -- 1 set

CABLE TIE 1.5x5x400mm -- 1 pc.

DOUBLE-SIDED TAPE 40x100mm -- 1 pc.

13.SCREW PB2x16mm -- 6 pcs

FUEL TUBE Ø6x5mm -- 2 pcs

CLEVIS PL4112103 -- 2 pcs

TRI-HORN M3x22mm(L) PL4111251 -- 2 sets

PUSHROD Ø1.8x1000mm w/ Threads(For Elevator Servo) -- 2 pcs

14.SCREW PB2x16mm -- 3 pcs

FUEL TUBE Ø6x5mm -- 1 pc.

CLEVIS PL4112103 -- 1 pc.

TRI-HORN M3x22mm(L) PL4111251 -- 1 set

PUSHROD Ø1.8x1065mm w/ Threads(For Rudder Servo) -- 1 pc.

15.FLYING WIRE Ø1x1300mm -- 1 pc.

FLYING WIRE BRACKET PL4112600 -- 6 pcs

FLYING WIRE BRACKET CLEVIS -- 4 pcs

EYE SCREW M1.8x6x12mm -- 4 pcs

SCREW PM2x16mm -- 6 pcs

SCREW PM2x8mm

-- 4 pcs

M2 NUT -- 6 pcs

WASHER d2xD5mm -- 6 pcs

COPPER TUBE d2.5xD3.2x8mm (For Rudder) -- 8 pcs

16.SIDE WINDOWS -- 1 pair

17.LINKAGE CONNECTOR Ø2.1mm -- 1 set

18.PLYWOOD 3x153x210mm(For Fuselage Servos) -- 1 pc.

FUEL TUBE Ø6x5mm -- 2 pcs

STRAPER PL4112102 -- 2 pcs

PUSHROD Ø1.8x85mm(For Elevator) -- 1 pc.

PUSHROD CONNECTOR 4x9x20mm PL4410010 -- 1 set

SPONGE 10x80x200mm -- 2 pcs

19.SCREW PWA2x12mm -- 4 pcs

PILOT PC001102A -- 1 set

COCKPIT BASE PANEL 3x145x165mm -- 2 pcs

20.SCREW PWA2.3x12mm -- 4 pcs

SCREW PM2x14mm -- 2 pcs

WASHER d2xD5mm -- 4 pcs

SILICON GROMMET d1.5xD6.5mm(For Wind Shield) -- 4 pcs

M2 NYLON INSERT LOCK NUT -- 2 pcs

WIND SHIELD -- 1 pc.

MOUNTING PLATE 5x15mm -- 2 pcs

21.WING TUBE Ø16x661mm -- 2 pcs

SELF-TIGHTENING LATCHING PIN PL9120010 -- 4 pcs

WIRE Ø0.8mm -- 2 pair

M3x8mm SET SCREW -- 4 pcs

22.SOCKET HEAD SCREW M3x8mm -- 2 pcs

WASHER d3xD7mm -- 4 pcs

M3 NYLON INSERT LOCK NUT -- 2 pcs

23.DECALS:A036DEC -- 1 set

All manuals and user guides at all-guides.com

A036PO30501409

Aileron & Flap Servo

Main Wing

Pre-glued

Aileron & Flap Servo Lead

P.3

Bottom View

PWA 2 x 8mm

1mm

Fuel Tube

Ø6x5mm

Straper

Fuel Tube

Ø6x5mm

PB2x30mm

Tri-horn

M3x22mm

Clevis

Pushrod

Ø1.8x120mm

PWA 2 x 8mm

1mm

Ø1mm pilot holes for The Wings Maker horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

tri-

TWM PL8210010

CLEVIS WRENCH

PB2 x 30mm Screw

PWA2 x 8mm Screw

All manuals and user guides at all-guides.com

A036PO30501409

M3 Nut

Stabilizer & Elevator

COMPLETED

5Vertical Fin & Rudder

COMPLETED

Pre-glued

(Stabilizer)

(Main Wing)

B B'

B=B'

M3x15mm

Washer d3xD7mm M3 x 15mm

Main Wing Strut

Bottom View

Temporary install the main wing, adjust

leveling of the stabilizer to make it as

parallel to the main wing as possible.

Wing Struts

380mm 369mm

202mm

193mm

69mm

P.4

Pre-glued

M3 Nut

d3xD7mm Washer

C C

69mm

d3xD7mm

Washer

M3 x 15mm Screw

Plastic Wire Bracket

All manuals and user guides at all-guides.com

A036PO30501409

Tail Landing Gear

PA1.7x8mm

Collar

M3x3mm

Set Screw

M3x3mm

Set Screw

Collar

Bottom View

PM3x13mm

d3xD7mm

Washer

M3 Nut

Plastic Wire

Bracket

7 Main Landing Gear

Front

PA3x12mm

P.5

1.5mm

PA3x14mm Screw

PWA2x12mm Screw

PA3x14mm 3.1mm Collar

1.5mm

Copper Plate

1x10x40mm

M3x3mm

Set Screw

M3x3mm

PA3 x12mm Screw

d3xD7mm Washer

8 Main Landing Gear

PA1.7 x 8mm Screw

PM3 x 13mm Screw

M3 Nut

3mm Set Screw

4.6mm Wheel Collar

PM3 x 13mm Screw

PM3x13mm PM3x13mm

Aluminum Plate 2mm

d3xD7

Washer

All manuals and user guides at all-guides.com

all-guides.com

A036PO30501409

P.6

Engine Mount

PL 5111080

Socket Head Screw

M4 x 30mm

Washer

d4.2xD14.5mm

D4.2xD14 5mm Washer.

Blind Nut

7.5mm

Determine the angle of

installation of the engine

mount so the muffler

will not contact the

fuselage.

M4x30mm

Socket Head Screw

5.5mm

Engine

D4xD12mm Washer

Throttle Pushwire

Ø1.2x480mm

Plastic Tube d2xD3x300mm

147mm

5.79 in.

Installed Engine Position

d4xD12mm

Washer

M4x35mm

SOCKET HEAD SCREW

NYLON INSERT LOCK NUT

Copper Tube d4.1xD5x67.2mm

M4x30mm

Sock Head Screw

Make sure the rounded

edges are facing the

shock absorbing

SILICON PAD.

KM3x20mm Screw

Copper Tube

d3.1xD4x7.2mm

M3 Nylon Insert

Lock Nut

D4xD9mm

Washer

ANTI-VIBRATION MOUNT INSTALLATION

d4xD12mm Washer

M4 NYLON INSERT LOCK Nut

M4x35mm

Socket Head Screw

All manuals and user guides at all-guides.com

A036PO30501409

Cowling

PWA2 6x12mm Screw.

d1.5xD6.5mm Silicon Grommet

First insert the grommet to the cowling then apply screw.

Please refer to the attached

sheet for usage of the

transparent 3D template.

P.7

Fuel Tank

450cc

COMPLETED

Fuel Filler

PL8110030

COMPLETED

Double-sided Tape

40x100mm

Cable Tie

1.5x5x400mm

PWA2.6x12mm

Silicon Grommet d1.5xD6.5mm

Cowling

Fuselage

All manuals and user guides at all-guides.com

A036PO30501409

Rudder

Pushrod

Elevator Pushrod

Bottom View

P.8

Fuel Tube

Ø6x5mm

Clevis

Tri-horn

M3x22mm

PB2x16mm

TWM PL8210010

CLEVIS WRENCH

TWM PL8210010

CLEVIS WRENCH

PB2x16mm Screw

Clevis

PB2x16mm

Fuel Tube

Ø6x5mm

Tri-horn

M3x22mm

Ø1mm pilot holes for horn are pre drilled. The Wings Maker tri- -

Ø1mm pilot holes for horn are pre drilled.

Please look for pin-hole marks at under side of control surfaces.

The Wings Maker tri- -

186mm

65mm

145mm

43mm

All manuals and user guides at all-guides.com

A036PO30501409

Servo Set

15 Flying Wire

Windows

Securely glue the windows to the fuselage.

COMPLETED

Window A

Copper Tube

Press down the center

1/3 portion

P.9

3x3mm Set Screw

Linkage Connector

M2 Nut

2mm Washer

Please refer to the attached sheet for linkage connector installation.

3x3mm Set Screw

Throttle Servo.

2mm

Washer

M2 Nut

2mm

Washer

PM2x16mm Screw

PM2x8mm Screw

M2 Nut

PM2x8mm Clevis

d2.5xD3.2x8mm

PM2x16mm

PM2x8mm

2mm

COPPER PLATE

1x10x40mm

Window B

COMPLETED

d2xD5mm

3mm

Washer

All manuals and user guides at all-guides.com

A036PO30501409

Pilot

Wind Shield

PWA 2x12mm Screw

18 Radio Equipment

Sponge

Throttle Pushrod

D1.2x480mm

Plastic Tube

d2xD3x300mm

Battery

Receiver

Throttle Servo

Plywood

3x153x210mm

Charge

Receptacles

KP0041300

I nstall and arrange the servos as shown in the diagram.

PC001102A

PWA 2x12mm Screw

d1.5xD6.5mm

silicon Grommet

PWA2.3x12mm

P.10

KM 2x8mm

M2 Nut

Elevator Push rod

Ø1.8x85mm

Elevator Servo

Pushrod Connector

J1(Pushrod Ø1.8x85mm)

J2(Pushrod Ø1.8x1000mm)

M2 NYLON INSERT LOCK NUT

PM2x14mm

d2xD5mm

Washer

PWA2.3x12mm Screw

d1.5x6.5mm Silicon Grommet

M2 NYLON INSERT LOCK NUT

PM2x14mm Screw

d2xD5mm Washer

All manuals and user guides at all-guides.com

all-guides.com

A036PO30501409

P.11

Main Wing

Wing Tube

Ø16x661mm

Set Screw

M3 x 8mm

Wing Tube PWA2.3x12mm

Self Tightening

Wing Latch

Set Screw

M3X8mm

M3x8mm

Set Screw

Wire

Ø0.8mm

Completed

Wing Tube

Long slot

Short slot

All manuals and user guides at all-guides.com

A036PO30501409

Wing Setting

Adjust the wing and fuselage configuration as shown

in the diagrams.

Wing Struts

Screw

M3x8mm

Washer

d3xD7mm

M3 NYLON INSERT LOCK NUT

P.12

M3 x 8mm

Socket Head Screw

d3xD7mm Washer

M3 Nylon Inert Lock Nut

All manuals and user guides at all-guides.com

A036PO30501409

24 Control Throws

Adjust the control throws as shown in

the diagram. These throws are good for

general flying. You can adjust according

to your personal preference.

Ailerons(away from fuselage)

20mm

Elevator

40mm

Rudder

55mm

25 C.G.

55mm

40mm

20mm

4.0 in.

Flaps (near fuselage)

40mm

C.G.

P.13

Important Safety Precautions

Warning!

# First time flyer should never fly by himself / herself. Assistance from experienced

flyer is absolutely necessary.

# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly

pre-adjusted aircraft.

# is specially designed to be powered by 2C 0.91 or 4C 1.20-1.60, using

a more powerful engine does not mean better performance. In fact, over powered

engine may cause severe damage and injuries.

# Make sure the air field is spacious, never fly the plane too close to people and never

get too close to a running propeller.

# If you find wrinkles on the covering as a result of weather changes, you can use hot

iron to remove the wrinkles. Please begin with lower temperature setting and

gradually raise the temperature until the wrinkles are gone. Too hot an iron may

damage the covering. Don't use hot iron near the seams or edges, hot iron will

melt the glue and shrink the covering at the same time, causing the seams to pull away.

# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

1/4 SUPER CUB

10 mm2

4.0 in.

http://www.theworldmodels.com/para/instruction/instructionManuals.php

All manuals and user guides at all-guides.com

A036PO30501409

LINKAGE CONNECTOR

HW7111050 & HW7111060

After fastening the round nut, make sure that

the linkage connector can rotate freely.

Drill 2mm hole at servo horn.

Insert linkage connector

into servo horn.

Make sure shoulder of

screw is cleared from

servo horn.

Add washer to reduce

play if necessary.

Shoulder

Tighten up the round nut

against the shoulder. Apply

CA or permanent thread

locker.

Product Registration Form (US Customers)

We would like to share with you any relevant information regarding your model, including

product news and free upgrade parts when applicable. Please fill in the following and send to

AirBorne Models, 4749-K,Bennett Drive, Livermore, CA 94551 USA.

1. Name:

2. Address:

3. Phone #: E-mail:

4. Model:

Wing QC# Fuselage QC#

(QC numbers are stamped on wing and fuselage)

5. Date of Purchase:

6. Store Name:

Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.

Thank you very much for purchasing our product.

All manuals and user guides at all-guides.com

A036PO30501409

Usage of the transparent 3D template

This transparent 3D template

is used for position guidance

of the actual cutting of the

pre-painted cowling.

Simply cut the transparent 3D template to fit your engine and

exhaust pipe, then slide onto the actual cowling and use as

template to mark the openings required for final cutting.

All manuals and user guides at all-guides.com

all-guides.com

A036PO30501409

Code No.Size Package

Code No SV4031

KP0041300

Special tool for clevis installation.

Suitable for standard and small

(EP)clevis.

Large Clevis

Small Clevis

All manuals and user guides at all-guides.com

A036PO30501409

All manuals and user guides at all-guides.com

This manual suits for next models

Other The World Models Manufacturing Toy manuals