THEIS VISION H User manual

VISION H
Instruction manual EN

2
Contents
Introduction.………………………………………………. 3
Keyboard / Display…………………...............................
4
1. Horizontal Operation ……………………….……….
4
2. Tilt Function..........................................................
4
3. Power Supply of Laser ……………………….….... 5
4. Detector.…………..……..…………..………....…... 6
TE 6…………………………....................................
7
TE 7........................................................................
8
5. Calibration Check ..............…………………….….. 9
6. Delivery Contents…………………………………....
9
7. Special Indications and Troubleshooting...………..
9
8. Warranty.……………………………………………...
9
9. Technical Data…...…………………………….….…
10
10. Supplier Declaration/Safety Information.….….......
11
11. Disposal.……….....…………….………………….…
12
Laser Warning Sign .……………………………………..
13

3
Introduction
VISION H
... for the construction professional.
The rotation laser THEIS VISION H sets new standards in the area
of fully automated professional lasers.
It is the result of many years of experience and innovative technol-
ogy.
The high-quality construction laser is distinguished by its rugged-
ness and high precision – Made in Germany – and no construction
site should do without it.
To ensure that your device is always ready for use, observe the
following information:
1. Never store the device in the container when it is wet.
2. Check the precision every time before you use the equipment,
since we can accept no liability for misalignment.
3. Observe the information on handling the battery.
4. Treat carefully the laser exit and sensor windows of the optional
detector.

4
Keyboard /Display
1. Horizontal Operation
Align the tripod and screw the VISION tight using the
tripod screw. Use the On/Off switch to switch on the
device.
The Laserbeam and the levelling LED is blinking.
If the tripod head is sloping by more than 5°, this is in-
dicated by the laser beam flashing quickly and the
Level LED.
In this case, switch off the unit and align the tripod
more carefully.
Once horizontal levelling is completed, the laser beam
starts to rotate at the last set speed. The
LED goes out.
2. TILT Function
In the case of major changes to the mounting position
(e.g. accidentally moving the tripod leg), a TILT
function ensures that the device switches off and
draws attention to the fact by the laser beam and the
levelling LED flashing quickly.
Then the device must be rebooted.
Laser exit rotation
Charging socket
Batter
y
Display
Battery compartment
On/Off
LED Levelling/
Disturbance
Product
-
information
Via QR-Code
on reverse, e.g.
Instruction
manual

5
3. Power Supply of Laser
When the red LED of the Battery display is blinking the
battery is almost flat. You can work at least 1 hour. The
instrument will switch off.
Charge the battery at room temperature using only the
THEIS standard mains unit connected to the charger
socket below the laser. Charging at temperatures below
+5°C can lead to defects in the battery.
Charging is also possible during operation. Overloading
is not possible.
The LED is blinking alternating during charging the
battery. If the battery is charged ready, the LED is
constantly on, as long as the charger is connected.
Only use the charger on dry premises!
The batteries that are used with Eneloop™
technology have the advantage of low levels of self-
discharge. This means that if you do not use the
device, you only need to recharge it every six
months.
In the battery compartment, you can also use normal
alkaline mono-cells. Under no circumstances must you
recharge them. If you do this by mistake, the battery
symbol flashes.
Important: Observe the correct polarity. There are
±symbols on the base of the battery compartment.
Observe the disposal information in point 11.
Important: Because the battery poles and contacts
may soil over time, resulting in contact problems,
regular inspection and possibly cleaning with a soft
cloth and cleaning agent (spirit, alcohol) are neces-
sary.

6
4. Detector
Switch on the detector by pressing the On/Off button and
selecting the desired function: Fine or coarse setting (basic
setting of TE 6/7 is coarse) and audible signal. The selected
function is shown on the LCD display.
Apart from this, the display shows you during measurement
about the direction in which you must move the detector (by
means of arrows).
Point the sensor window to the VISION and move it through the
rotating laser beam until there is a display on the LCD. Then
keep following the arrow with the detector until only the centre
bar is displayed continuously.
If the hooter is switched on, a continuous tone is issued when
the bar is displayed. When the arrow is displayed, a differently
pulsating tone indicates whether the detector is being held too
high or too low.
With the TE 7, you set the volume of the hooter in three stages.
If no laser beam hits the detector field (sensor window) for
approximately seven minutes, the detector switches off.
Power supply of detector
If the battery symbol is shown on the LCD display, you should
change the 9 V, E-block battery; otherwise, the range may be
limited.
Open the folding lid of the battery compartment to change the
battery.
Dispose of used batteries correctly (see point 20) and ensure the
correct polarity with the new batteries (observe the symbols).

7
TE 6
Display
Fine Coarse
Arrow for direction
of movement
Centre bar
Arrow for direction
of movement
Battery display Display of audible signal
LCD display
(on reverse too) Centre notch
On/Off button Fine/Coarse button
Button or issuing of
audible signal
Battery compartment
(on reverse)
Sensor window

8
TE 7
Display
Coarse Fine
Arrow for direction of movement
(Near centre bar)
Centre bar
(Near centre bar)
Arrow for direction of movement
Display of audible signal Battery display
(3 stages)
Issuing ofaudible Sensor window
signal (on reverse)
Illuminated
LCD – Display
(on reverse too) LED for direction
of movement
Centre notch LED for Centre
LED for direction
of movement
On/Off Illumination
Audible signal Fin / Coarse
Battery compartment
(on reverse)

9
5. Calibration Check
Set up the laser leveller as described in point 1. (but on an
extremely well aligned tripod) and align it along a traverse length of
approximately 30 metres – starting with the X axis, for example –
and switch it on.
At the end of the traverse length, make a mark at the level of the la-
ser beam. After this, rotate the laser unit by 180° and make another
mark. Then do the same for the Y axis. If all the marks are on top of
each other or are only slightly apart (maximum of 2 mm), adjust-
ment is OK. If the marks are a long way apart, you must get a spe-
cialist firm to check the equipment and recalibrate it.
6. Delivery Contents
Standard Option
Laser Detector
Rechargeable batteries Tripod
(4 Mono-cells)
Power supply unit
Instruction Manual
Protective case
7. Special Indications and Troubleshooting
Quick blinking level LED (Exception: Self-levelling range is
exceeded or Tilt)
Send the equipment for inspection only to an authorized service
partner or directly to the manufacturer.
8. Warranty
We guarantee our products to be free from faults in material and
workmanship according to the current state of the art. Should
defects of this type arise in practical use, they will be eliminated free
of charge. The warranty period is 36 months (apart from the
rechargeable battery, which is 1 year) from the date of sale (date of
invoice). You must return the device or its affected components for
repair or replacement to THEIS immediately after you establish the
defect.

10
No guarantee claim or claim free elimination of faults due to
incorrect handling or storage can be accepted; in addition, no
claims for damages can be accepted, including claims for damages
in particular claims for indirect damages. Furthermore, any and all
claims for damages will be void in the case of any technical
intervention by third parties, i.e. not by THEIS.
9. Technische Daten
Laser
Laser Class / High
Power
2 / 3R
Wavelength
635 nm
Ouput Power / High Power
< 1mW / < 5 mW
Range
See detector
Self
-
levelling range
± 5°
Levelling precision
3,4
±
1,
5 mm /
3
0 m
Speed 600 RPM
Power supply
NiMH
+
4x 1.2 V, 8Ah
or 4x 1.5V alkaline mono
-
cells
Running time
rechargeable
battery/battery
2,3
≈
7
0h / 120h
Charging time
≈
6
h
Working temperature
-
1
5
to + 50°C
System of protection
IP 67 waterproof
Weight
≈3 kg
Detector (option) TE 6 TE 7
Detector field
45 mm 45 mm
Range with basic unit
1,3
250 m 350 m
Range with High Power
1,3
550 m 700 m
Precision:
Fine / Coarse
± 2 mm / ± 4 mm
Running time
2,3
≈36 h ≈50 h
Power supply
9 V, E-Block
Operating temperature
-15 till + 50°C
System of protection
IP 65
Size
135 x 65 x 24,5 mm
165 x 76 x 35 mm
Weight
≈195 g ≈390 g
1) Under optimum atmospheric conditions.
2) Under optimum conditions
3) At 20°C
4) Parallel to the main X, Y axes

11
10. Supplier Declaration/Safety Information
The device complies with European Directives:
2004/108/EG, RTTE 1999/5/EG sowie 2011/65/EU
Harmonized standards:
EN 60950-1, EN 61000-6-3, EN301489-1, EN300220-1 V2.4.1,
EN 61000-6-2, EN301489-3 und EN300220-2 V2.4.1
A safety information plate is on the left-hand side of the device
An embedded Class 3R (3B with the High Power version) laser
is installed. This means that when you open the device there is
a possibility of entering the range of power values that are
higher than Class 2 (3B with the High Power version). If
possible, do not point the laser at people. Do not look into the
laser beam even with optical instruments.
There are no parts to maintain or adjust inside the device.
Servicing may only be carried out by authorized persons.
Safety regulations for
THEIS Class 3R HIGH-POWER LASER DEVICES
Users must observe BGVB2 (Accident Prevention Regulations for
Laser Radiation in Germany).
•Only trained personnel are allowed to operate this product to
avoid radiation with dangerous laser light.
•The laser is subject to Class 3R
•Do not remove the warning signs on the device!
•Observe and secure the beam path over a large distance!

12
•Never look into the laser beam or shine it into other peoples'
eyes! This also applies at a large distance from the device!
•Always set up the laser such that people cannot be shone on
at eye level (pay attention to reflections).
11. Disposal
The surveying device, its accessories and packaging should be
recycled in an environmentally friendly way.
EU countries only:
Never put electrical tools in domestic refuse!
In accordance with EU directive 2012/19/EC concerning
Waste Electrical and Electronic Equipment and its
transposition into national legislation, measuring
equipment that can no longer be used must be collected
separately and recycled in an environmentally friendly
way. (WEEE - Reg. No. DE 10598800)
Rechargeable batteries:
Never put rechargeable batteries in domestic refuse, a fire or into
water. In accordance with Directive 2006/66EC, defective or spent
rechargeable batteries must be recycled or disposed of in an
environmentally friendly way.
EU countries only:
In accordance with Directive 2006/66EC, non-serviceable THEIS
laser devices or spent rechargeable batteries must be recycled or
can be returned directly to:
THEIS FEINWERKTECHNIK GMBH
Zum Bolzenbach 26
D- 35236 Breidenbach
+ 49 (0) 6465 - 67- 0
+ 49 (0) 6465 - 6725
[e-mail]

13
Laserwarnschild für VISION
Laser warning label for VISION
Signal de danger « Laser » pour VISION
Laserwarnschild für VISION High Power
Laser warning label for VISION High Power
Signal de danger « Laser » pour VISION High Power
Änderungen vorbehalten
Subject to changes
Sous réserves de modifications
THEIS FEINWERKTECHNIK GMBH
35236 Breidenbach-Wolzhausen·Germany
05.08.2015