Therian 5 Tier Cat Tower Parts User manual

Assembly Instructions
5 Tier Cat Tower Parts
Parts List
• (A) 5 x Vinyl Fabrics
• (B) 6 x Leg Caps
• (C) 6 x Top Corners
• (D) 34 x Bottom Corners
• (E) 40 x Screws
• (F) 40 x Nuts
• (G) 40 x Washers
Tier Pipes - With Channels
• (H) 10 x 41cm (16”) Tier Pipe
• (I) 10 x 27.7cm (11”) Tier Pipe
Leg Pipes - No Channels
• (J) 4 x 41cm (16”) Leg Pipe
• (K) 2 x 31.7cm (12.5”) Leg Pipe
• (L) 2 x 21.5cm (8.5”) Leg Pipe
• (M) 6 x 17.8cm (7”) Leg Pipe
• (N) 6 x 8.2cm (3”) Leg Pipe
Needed:
• Flat Surface To Work On
• Phillips Head Screwdriver
• Adjustable Wrench or Pliers
• Optional: Rubber Mallet
(A) Vinyl Fabrics
(B) Leg Caps
Leg Pipes
Tier Pipes
(D) Bottom Corners
(E)
Screws
(G)
Washers
(F) Nuts
(C) Top Corners
(I) 27cm
(N) 8.2cm
(L) 21.5cm
(H) 41cm
(M) 17.8cm
(K) 31.7cm
(J) 41cm
1

5 Tier Cat Tower
Assembly Instructions
Product Advisory
To maximize the life of the corner ttings, do not use excessive force to tighten screws and
nuts. Do not use power tools to assembly the bed. Please be aware that over tightening the nuts
located on the corners of the beds can cause enough added stress that the corner pieces may fail.
Periodically check hardware to prevent indigestion hazards to dogs and cats.
Cleaning
It is recommended to use warm soapy water and hose down or pressure clean the Kuranda beds.
One Year Chew-Proof Warranty
We guarantee the structural integrity of each of our Kuranda beds for a period of one year from the
original date of purchase of the bed. If your dog or cat is able to damage any part of the frame or
fabric by chewing beyond usability, we will send out replacement parts free of charge.
The 1 year chew-proof warranty does not cover cosmetic damage or damage caused by
persistentscratching/digging; nor corner pieces that fail due to over-tightening of screws and nuts.
(A)
(J)
(N)
(K)
(N)
(M)
(M)
(M)
(D)
(C)
(H)
(H)
(H)
(J)
(I)
(I)
(I)
(I)
(A)
Tier 2
Tier 1
Tier 3
Tier 5
Tier 4
(A)
(A)
(A)
(H)
(D)
(D)
(D)
(L)
(C)
(B)
(B)
(B)
2

5 Tier Cat Tower
Assembly Instructions
Step 1.
With the fabric (A) seams facing up,
insert the long edges of the fabric
into the channel of tier pipe (H).
Insert the short edges of the fabric
into the channel of tier pipe (I).
Repeat for each fabric (A).
Step 2.
To assemble Tier 1, with fabric
seams still facing up, secure tier
pipes (H) and (I) between a top
corner (C) and a bottom corner (D).
Lightly secure with a screw (E),
washer (G) and nut (F).
Repeat for all 4 corners.
Once Tier 1 corners are assembled,
completely fasten nuts. Flip over
so seams are facing down.
Step 3.
To assemble Tier 2, repeat step 2
for 2 corners along one length of
another fabric (A).
For the remaining 2 corners,
secure tier pipes (H) and (I)
between two bottom corners (D)
and lightly fasten.
Once tier 2 corners are assembled,
completely fasten nuts.
Step 4.
To assemble Tiers 3, 4 and 5 with the
remaining fabrics, secure tier pipes
(H) and (I) between two bottom
corners (D) and lightly fasten.
Once Tier corners are assembled,
completely fasten nuts.
Repeat for all 4 corners on each
remaining fabric (A).
NOTE:
Insucient or over
tightening of the corners
may result in cracking,
which is NOT covered by the
1 year chew-proof warranty.
Parts Required: (A), (C), (D), (E), (F), (G), (H), (I)
Part 1. Assemble the Tiers
(A)
(A)
(A)
(A)
(C)
(C)
(D)
(E)
(D)
(D)
(F)
(G)
(H)
(E)
(E)
(H)
(H)
(H)
(I)
(I)
(I)
Tier 1
Tier 2
Tiers
3, 4
and 5
3

5 Tier Cat Tower
Assembly Instructions
Parts Required: Tier Type 3s, (B), (J), (K), (L), (M), (N)
Part 2. Assemble the Tower
Step 5.
Insert leg caps (B) into 4 (N) leg pipes.
Insert the 4 (N) leg pipes with leg caps
into the underside corners of Tier 5.
Place on floor with leg caps on the ground
and ensure the tier is secure and level.
Face one Tier 5 (I) tier pipe towards you
and insert the 2 (N) leg pipes without leg
caps into the left 2 topside corners.
Insert 2 (K) leg pipes in the
right topside corners.
Step 6.
To add Tier 4, insert the remaining 2 leg
caps (B) into 2 (L) leg pipes.
Insert the 2 (L) leg pipes with leg caps into
the left bottomside corners of Tier 4.
Insert the right bottomside corners of
Tier 4 onto the Tier 5 topside (N) leg pipes.
Ensure the tiers are secure and level.
Insert 2 (M) leg pipes into the right 2
topside corners of Tier 4.
Insert 2 (J) leg pipes into the left topside
corners of Tier 4.
Step 7.
Place Tier 3 onto the leg pipes
(K and M) over Tier 5.
Ensure the tiers are secure and level.
Insert 2 (M) leg pipes into the left
topside corners of Tier 3.
(K)
(B)
(B)
(B)
(I)
(N)
(N)
(M)
(M)
(M)
(K)
(J)
(L)
(N)
Tier 5
Tier 4
Tier 3
Tier 4
Tier 5
Tier 5
4

5 Tier Cat Tower
Assembly Instructions
Parts Required: Tier Types 1 and 2, All Leg Pipes
Part 2. Assemble the Tower
Step 8.
With the top corners (C) of Tier 2
to the left, place Tier 2 onto the leg
pipes (M and J), over Tier 4.
Insert the remaining 2 (M) leg pipes
into the right topside corners of Tier 2.
Ensure the tiers are secure and level.
Step 9.
Insert Tier 1 onto the leg pipes
(M and J), over Tier 3.
Ensure the tiers are secure and level
to complete the 5 Tier Cat Tower.
Tier 3
Tier 4
Tier 3
Tier 5
Tier 2
Tier 2
(M)
(M)
(M)
(J)
(C)
(J)
(J)
5
Therian Pty Ltd.
therian.com.au/kuranda | [e-mail]
1800 251 766 | 07 5657 6777
Unit 4, 26 Commercial Drive, Ashmore, QLD, 4214, Australia