three h UPSIDE User manual

UPSIDE

8 x 11 /4 " Screw
Used on: Controller
Worksurface
Column Base
Controller Cable Management
Power Feed Power Supply
Leg Column
M6 x 16mm
Used on: Leg Columns & Bases
5/32” Allen Wrench
(Provided)
Roberston Screwdriver
INCLUDED HARDWARE
REQUIRED TOOLS
GETTING STARTED
Assemble on a soft surface to avoid scratching the worksurface.
Page 2

• Product that is damaged by the end user due to misuse, accident, abuse,
negligence or shipping is not covered under Three H warranty.
• Use tools and hardware mentioned above to avoid any product faults.
• It is best to assemble our furniture with 2 or more persons.
• If you believe you are missing pieces, please contact [e-mail]
DISCLAIMERS!
Hardware & tools required may vary depending on the UpSide™ specifics.
The following instructions do not specify the amount of hardware included.
Due to variations in design, a separate hardware list will be provided.
Page 3
RESETTING DESK HEIGHT
Linak Desk Control App Manual
Please download the Linak App to reset your desk height.
• Measure from the floor to the top of the worksurface
at it’s lowest height.
• Write the height down
In the Linak App:
• Click More > Set Desk Height
• Input the height you marked down
Follow the instructions using the link below to reset your desk
height manually.
• www.linak-us.com/segments/deskline/start/dpg1c/

Page 4
STEP 1
STEP 2
STEP 3
Place the worksurface face down on a
soft, clean surface.
Install the Leg Columns
Install the Leg Column Bases
Place the Leg Columns between the
pre-assembled brackets. Fasten each
column using six M6 x 16mm screws.
The worksurface is shipped with some
pre-assembled hardware components.
Line up the pre-drilled holes on the
Column Base to Leg Column and
fasten each base using four M6 x 16mm
screws.

STEP 4
Connect Power Feeds
Plug the Power Feeds in from each
Leg Column to main Power Supply
Box.
STEP 5
Mount the Controller
Locate the pre-drilled holes and mount
the Controller using two 8 x 11 /4 " Screws.
STEP 6
Plug in the Controller
Plug the Controller in to the main power
supply box.
Page 5

STEP 7
Connect Main Power Supply
Plug the main power supply into the
supply box. Keep the wire tied in the
twist tie until the next step.
STEP 8
Flip The Desk
Flip the desk and plug the main power
source in.
Please scan the QR code or use this link:
https://bit.ly/2Fgmsjk
This PDF from Linak will describe how to
initialize the controller and other safety
precautions.
STEP 9
Controller Start Up
Page 6

Page 5 of 28
Safety instruction
General
Important information
Important information on LINAK®products can be found under the
following headings:
Warning!
Failure to comply with these instructions may result in accidents
involving serious personal injury.
Failing to follow these instructions can result in the product being
damaged or being destroyed.
Safe use of the system is possible only when the operating instructions
are read completely and the instructions contained are strictly observed.
Failure to comply with instructions marked with the ”NOTE” symbol may
result in serious damage to the system or one of its components.
It is important for everyone who is to connect, install, or use the
systems to have the necessary information and access to this User
Manual. Follow the instructions for mounting – risk of injury if
these instructions are not followed.
The appliance is not intended for use by young children or infirm
persons without supervision.
If there is visible damage on the product it must not be installed.
Note that during construction of applications, in which the actuator
is to be fitted, there must be no possibility of personal injury, for
example the squeezing of fingers or arms.
Assure free space for movement of application in both directions to
avoid blockade.
Page 7

Three H Furniture Systems Limited
156462 Clover Valley Rd.
New Liskeard, ON
Canada P0J 1P0
T. 1.800.767.5374
F. 1.888.484.5786
[e-mail]
www.three-h.com © 2020 Three H Furniture Systems Limited. All rights reserved.
Revision 3 · January 6 2020