three h Woodstock User manual

Woodstock
General Installation
Credenzas
Fixed, Freestanding, Height Adjustable
Worksurfaces

INDEX
Woodstock Instructions 1
Index
Hardware & Tools
Possible Parts
Double Plinth Base Assembly
Double Elevated Base Assembly
Plinth Base + Credenza Assembly
Elevated Base + Credenza Assembly
Cushion Platform Assembly
Gussett Assembly
Floating Run-Off Worksurface Assembly
Run-Off Worksurface Assembly
Freestanding Worksurface Assembly
Height Adjustable Worksurface Assembly
Modesty + Trough Assembly
External Links & Information
1
2
3
4
5
6-7
8
9-10
11
12-13
14-15
16
17-20
21
22

• Product that is damaged by the end user due to misuse, accident, abuse,
negligence or shipping is not covered under Three H warranty.
• Use tools and hardware mentioned above to avoid any product faults.
• It is best to assemble our furniture with 2 or more persons.
• If you believe you are missing pieces, please contact [e-mail]
DISCLAIMERS!
Woodstock Instructions 2
REQUIRED TOOLS
Phillips Screwdriver
Leveler
Robertson Screwdriver Ratchet or Wrench Allen Wrench (provided)
#8 x 5/8"
#8 x 3/4"
1/4" - 20 x 3/4" M6 x 10mm 1/4" - 20 x 2.5" 1/4" - 20 x 20mm M6 x 20mm
M6 x 25mm
Mini-Fix Pin Mini-Fix Connector
HARDWARE & TOOLS

Single Plinth Base Double Plinth Base
Elevated Credenza Plinth Credenza
Freestanding Worksurface
Gusset
Height Adjustable
Modesty & Trough Stacker
Plinth PlatformElevated Platform
Run Off Worksurface
Cushions
Floating Run Off
Single Elevated Base Double Elevated Base
No Assembly Required Assembly Required
Assembly Required Assembly Required
Assembly Required
Assembly Required
Assembly Required
Assembly Required No Assembly Required
Assembly RequiredAssembly Required
Assembly Required
Assembly Required
Assembly Required
No Assembly Required Assembly Required
Woodstock Instructions 3
POSSIBLE PARTS

1
2Fasten all of the screws evenly to ensure
pieces are flush before fully tightening.
Slide the 2 base pieces together.
Woodstock Instructions 4
#2 Robertson (Red)#8 x 5/8"
DOUBLE PLINTH BASE ASSEMBLY

Fasten the 1/4" - 20 x 3/4" bolts to attach
the bases.
Slide the base pieces together.
Fasten the middle legs onto the frame using
the 1/4" - 20 x 2.5" bolts.
Woodstock Instructions 5
Ratchet or Wrench
Ratchet or Wrench
1/4" - 20 x 3/4"
1/4" - 20 x 2.5"
DOUBLE ELEVATED BASE ASSEMBLY
1
2
3

Woodstock Instructions 6
Flip the base on it’s side.
Lay all credenza (cabinets and/ or platforms)
in their respective positions and align the
pre-drilled holes.
Insert the #8 x 5/8" screws and fasten all of
the screws evenly to ensure pieces are flush
before fully tightening.
PLINTH BASE + CREDENZA ASSEMBLY
Height Adjustable Worksurface Instructions on
page 17-20
Cushion Platform Instructions on page 9-10
1
2
3
#2 Robertson (Red)#8 x 5/8"

Woodstock Instructions 7
Tilt the entire credenza assembly upright
using a minimum of 2 people.
Move the credenza into its final position using
furniture slides or skates.
PLINTH BASE + CREDENZA ASSEMBLY
4

Woodstock Instructions 8
Place the credenza (cabinets and/ or platforms)
down on top of the base. Slide them to the left
or right as far as they will go.
Height Adjustable Worksurface Instructions on
page 17-20
Cushion Platform Instructions on page 9-10
Attention: This is the view from the bottom,
keep the unit upright.
Fasten all of the screws evenly to ensure
pieces are flush before fully tightening.
ELEVATED BASE + CREDENZA ASSEMBLY
1
2
Allen Wrench (provided)
Allen Wrench1/4" - 20 x 20mm

Woodstock Instructions 9
Insert the Mini-Fix Pins into the pre-installed
nuts. Fasten using a Phillips Screwdriver.
This piece is the "Back Rest".
Locate the Mini-Fix Connectors on the
"Base" of the platform and slide pre-drilled
holes onto Mini-Fix Pins. Fasten using a
Phillips Screwdriver
Mini-Fix Pin
Mini-Fix Connector
Phillips Screwdriver
Phillips Screwdriver
CUSHION PLATFORM ASSEMBLY
1
2

Woodstock Instructions 10
Place the Cushion Platform onto the Elevated
Base. Fasten using 1/4” - 20 x 20mm screws
and a ratchet or wrench.
Refer to page 8 on fastening instructions.
Prep the Cushion by removing the velcro
covers. Place down firmly in place for 1
minute or longer.
CUSHION PLATFORM ASSEMBLY
3
4
Allen Wrench1/4" - 20 x 20mm

Woodstock Instructions 11
On the back of the unit, align the gusset plate
to the pre-drilled holes.
Insert the M6 x 20mm screws to hold in
place and fasten each bolt equally until they
are all tight.
Allan Wrench
M6 x 20mm
GUSSET ASSEMBLY
1
2

Woodstock Instructions 12
Place the Worksurface on a clean, soft surface
and align the holes from leg to worksurface.
Insert the M6 x 25mm screws to hold in
place and fasten each bolt equally until they
are all tight.
FLOATING RUN-OFF WORKSURFACE ASSEMBLY
1
2
Allan Wrench
M6 x 25mm

Woodstock Instructions 13
Position the Worksurface. The Rubber
Bumpers will keep the desk in place.
FLOATING RUN-OFF WORKSURFACE ASSEMBLY
3

Woodstock Instructions 14
Place the Worksurface on a clean, soft surface
and align the holes from leg to worksurface.
Insert the M6 x 25mm screws to hold in
place and fasten each bolt equally until they
are all tight.
RUN-OFF WORKSURFACE ASSEMBLY
1
2
Allan Wrench
M6 x 25mm

Woodstock Instructions 15
Slide the Worksurface brackets into position. It
will slide inbetween the Sub-Top and Main Top.
If there is power, snake the cord through the
cut out and down the back of the credenza.
Modesty & Trough Assembly - Page 21
A: Insert the 1/4" - 20 x 20mm in the
pre-drilled holes, don’t fully tighten. This
will keep the worksurface positioned.
B: Insert the #8 x 5/8" to fasten the
worksurface. After that, finish tightening
the 1/4" - 20 x 20mm.
1/4" - 20 x 20mm
A: Position
B: Fasten
RUN-OFF WORKSURFACE ASSEMBLY
3
4
Allan Wrench#8 x 5/8"

Woodstock Instructions 16
Place the Worksurface on a clean, soft surface
and align the holes from leg to worksurface.
Insert the M6 x 25mm screws to hold in
place and fasten each bolt equally until they
are all tight.
FREESTANDING WORKSURFACE ASSEMBLY
1
2
Allan WrenchM6 x 25mm

Woodstock Instructions 17
Place the height adjustable credenza piece
down on top of the base. Slide it to the left or
right as far as it will go.
First, Fasten the M6 x 10mm bolts on the left
bracket.
Insert the 1/4" - 20 x 20mm screws to hold in
place and fasten each screw equally until they
are all tight.
HEIGHT ADJUSTABLE WORKSURFACE ASSEMBLY
1
2
M6 x 10mm Ratchet or Wrench
Allen Wrench1/4" - 20 x 20mm

Woodstock Instructions 18
Place the Worksurface on a clean, soft surface
and align the holes from leg to worksurface.
Fasten the leg to the worksurface using six
#8 x 3/4" screws and a #2 Robertson.
HEIGHT ADJUSTABLE WORKSURFACE ASSEMBLY
3
4
#2 Robertson (Red)#8 x 3/4"

Woodstock Instructions 19
Place the worksurface and make sure the
worksurface/ credenza are level, if required
adjust the foot levelers.
Fasten the power house using the pre-drilled
holes and provided M6 bolts.
Plug in the 3 legs.
Guide the power supply cord down the back
of the credenza and plug it in.
HEIGHT ADJUSTABLE WORKSURFACE ASSEMBLY
Leveler
5
6