three h At Home User manual

At Home & Small Office Essentials 1
At Home
General Installation

At Home & Small Office Essentials 2
INDEX
Hardware & Tools
Woodstock Table Desk Assembly
Frame Leg Desk Assembly
Workshelf Table Desk Assembly
UpSide Table Desk Assembly
WorkStop Table Desk Assembly
Hubub Table Assembly
Mobile Storage Pedestal Assembly
Freestanding Storage Assembly
Woodstock Plinth Base Assembly
Woodstock Elevated Base Assembly
Woodstock Cushion Platform Assembly
Woodstock Gusset Assembly
Woodstock Bench Assembly
Wall Mount Hutch Assembly
Wall Mount Tackboard Assembly
CordJacket Assembly
3
4
5-6
7-8
9-11
12-13
14-16
17
18-19
20
21
22
23
24-26
27-29
30-33
34-35

At Home & Small Office Essentials 3
• Product that is damaged by the end user due to misuse, accident, abuse,
negligence or shipping is not covered under Three H warranty.
• Use tools and hardware mentioned above to avoid any product faults.
• It is best to assemble our furniture with 2 or more persons.
• If you believe you are missing pieces, please contact [e-mail]
DISCLAIMERS!
REQUIRED TOOLS
Phillips Screwdriver
Leveler
Robertson Screwdriver Ratchet or Wrench Allen Wrench (provided)
#8 x 5/8"
1/4"-20x3/4" M6 x 10mm
1/4" - 20 x 2.5"
1/4"-20x20mm M6 x 20mm
M6 x 25mm
Mini-Fix Pin Mini-Fix
Connector
HARDWARE & TOOLS
M6 x 16mm
#8 x 1" M6 x 70mm
M6 x 20mm
Allen Key (Provided)
M6 x 25mm
M6 x 12mm
Dowels

At Home & Small Office Essentials 4At Home & Small Office Essentials
Place the Worksurface upside down on
a clean, soft surface and align the holes
from leg to worksurface.
Insert the M6 x 25mm screws to hold in
place and fasten each bolt equally until
they are all tight.
WOODSTOCK TABLE DESK
1
2
Allen Wrench
M6 x 25mm
Qty: 8

At Home & Small Office Essentials 5At Home & Small Office Essentials
Place the Worksurface on a clean, soft
surface and align the holes from frame
leg to worksurface.
On each leg, insert the six M6x25mm
screws into the threaded connectors
(img.1) and fasten each screw equally
until they are all tight.
FRAME LEG TABLE DESK
1
2
Allen Wrench
M6 x 25mm
Qty: 12
img.1

At Home & Small Office Essentials 6At Home & Small Office Essentials
Insert the twelve #8x1" Flat Head
square drive wood screws into the
holes as shown below (img.2) using a
drill / Robertson drillbit.
FRAME LEG TABLE DESK
3
#8 x 1"
img.2
Qty: 24
Robertson

At Home & Small Office Essentials 7
Place the Worksurface on a clean, soft
surface and align Brackets / Legs to the
Worksurface frame.
Insert two M6x70mm decorative flat
head bolts into the bracket connecting
through the frame. Fasten each screw
equally with an Allen Wrench until they
are all tight.
WORKSHELF TABLE DESK & LOUNGE TABLE
1
2
Allen Wrench
M6 x 70mm
Qty: 8

At Home & Small Office Essentials 8
Insert four m6x20mm decorative flat
head bolts into the bracket touching the
worksurface. Fasten each screw equally
until they are all tight.
WORKSHELF TABLE DESK
3
Allen WrenchM6 x 20mm
Qty: 16

At Home & Small Office Essentials 9
Place the Worksurface on a clean, soft
surface.
Place the Leg Columns between the
pre-assembled brackets. Fasten each
leg column using six M6x16mm screws.
Install the feet by lowering them into
place with the pre-drilled holes. Fasten
each foot using four M6x16mm screws.
UPSIDE TABLE DESK
1
2
Allen WrenchM6 x 16mm
Qty: 8
Allen WrenchM6 x 20mm
Qty: 12

At Home & Small Office Essentials 10
Plug the Power Feeds in from each Leg
Column to the main Power Supply Box.
Fasten the Controller using two 8x11 /4 "
screws to the left or the right of the
desk. Be sure it is easily accessible from
the side of choice.
UPSIDE TABLE DESK
3
4
#8 x 1"
Qty: 2
Robertson

At Home & Small Office Essentials 11
Plug the main power supply into the
supply box. Keep the wire tied in the
twist tie until the next step.
Flip the desk, level the glides, left to
right then front to back. Plug the main
power source in. From here, please scan
the QR code or follow the link below
for instructions on how to initialize the
controller and other safety precautions.
UPSIDE TABLE DESK
5
6
bit.ly/2Fgmsjk
Always maintain a 1" gap (min.) between the
edges of the worksurface and adjacent objects
or structures.
Do not install underneath shelves or objects
attached to wall that could become dislodged by
the worksurface.

At Home & Small Office Essentials 12
WORKSTOPS
Place the Worksurface on a clean, soft
surface and align Brackets / Legs to the
Worksurface frame.
The worksurface to wall brackets are
pre-installed. However, these will need
to align to your wall studs, so they may
require adjustments.
Insert two M6x70mm decorative flat
head bolts into the bracket connecting
through the frame. Fasten each screw
equally with an Allen Wrench until they
are all tight.
1
2
Allen Wrench
M6 x 70mm
Qty: 8

At Home & Small Office Essentials 13
Insert four m6x20mm decorative flat
head bolts into the bracket touching the
worksurface. Fasten each screw equally
until they are all tight.
Mark your wall studs to start. Each
bracket must have 1 screw fastened
into a stud.
Place the surface against the wall in
your desired location. Using your own
hardware based on the wall conditions,
attach the the worksurface to the wall
through the bracket on the underside of
the surface.
Screws are NOT provided to attach to the wall.
6 screws will be needed. Please use the appropriate
type of screw for your wall condition.
WORKSTOPS
3
4
Allen WrenchM6 x 20mm
Power Drill Wall Screws
(Not Provided)
Qty: 8

At Home & Small Office Essentials 14
HUBUB
Lower the oval top plate down to the
bottom of the large main post.
Loosely thread in 4 M6x12mm screws
from the top plate to main post flange.
Tighten screws equally with supplied
allen wrench.
1
2
M6 x 12mm
Qty: 4
Allen Key

At Home & Small Office Essentials 15
HUBUB
Align the small front post to the middle
hole and thread in one M6x12mm screw
from the bottom of the plate.
Tighten screw with provided allen
wrench.
Mount the Base Plate to the Posts from
Step 3. It’s easiest to do this with both
parts on their sides.
Loosely thread in 3 M6x25mm screws,
tighten equally with the provided Allen
Key until they are tight.
3
4
Allen Key
Allen Key
M6 x 12mm
Qty: 1
M6 x 25mm
Qty: 3

At Home & Small Office Essentials 16
HUBUB
Place the top onto the Post Flange and
insert 6 M6x12mm screws. Tighten the
screws equally using provided Allen
Key.
5
Allen Key
M6 x 12mm
Qty: 6

At Home & Small Office Essentials 17
Open one drawer at a time and remove
the pull screws from each drawer front
using a Robertson Screwdriver.
Align the pull to the pre-drilled holes
on the drawer fronts and re-attach
them using the provided screws and
Robertson Screwdriver.
MOBILE STORAGE PEDESTAL
1
2
5/8" No.2
5/8" No.2
Robertson Screwdriver
Robertson Screwdriver
Qty: 2
Qty: 2

At Home & Small Office Essentials 18
Open one drawer/ door at a time and
remove the pull screws from each
drawer/ door front using a Robertson
Screwdriver.
All Freestanding Storage needs to be
leveled, it’s recommended doing this
before adding in shelving.
Place the unit in position, level from
left to right and then front to back.
Align the pull to the pre-drilled holes on
the drawer/ door fronts and re-attach
them using the provided screws and
Robertson Screwdriver.
FREESTANDING STORAGE
1
2
5/8" No.2
5/8" No.2
Robertson Screwdriver
Robertson Screwdriver
Qty: 2
Qty: 2

At Home & Small Office Essentials 19
Insert 4 shelf brackets in the holes at
the desired height on each side.
Tilt the shelves and put them in place
over the shelf brackets. Ensure the
trimmed edge is facing outwards.
*Not all freestanding units will follow all
of these rules.
FREESTANDING STORAGE
3
4
Shelf Supports

At Home & Small Office Essentials 20
Flip the pre-assembled base onto the
side as well as the credenza on a clean,
soft surface.
2 people required for assembly.
Insert the #8 x 5/8" screws and fasten
all of the screws evenly to ensure
pieces are flush before fully tightening.
With 2 people, flip the credenza back
into an upright position.
Push the base and credenza together
and align the credenza brackets to the
pre-drilled holes in the base.
Brackets are shipped attached.
WOODSTOCK CREDENZA ASSEMBLY | PLINTH BASE
1
3
2
5/8" No.2 Robertson Screwdriver
Qty: 8