TiePie TP-EMI-HS6 User manual

EMI probe set TP-EMI-HS6
The EMI probe set TP-EMI-HS6 is a complete set of probes, conveniently packed
in a carry case. Together with the Handyscope HS6-1000, Handyscope HS6 DIFF-
1000, WiFiScope WS6-1000 or WiFiScope WS6 DIFF-1000 with option E installed,
it turns your instrument into an EMI pre compliance tester.
The set contains three differently sized H field probes and an E field probe. To con-
nect the probes to the scope, a short semi flexible antenna cable and a long flexible
antenna cable are included. For proper grounding and termination, a grounded
50 Ohm terminator is also included. The tripod allows exact positioning of the
probe near the test subject.
EMI probe set TP-EMI-HS6 1

Set contents
The EMI probe set TP-EMI-HS6 contains the following items:
TP-NFP-25 H field probe
25 mm diameter, female SMA connector
TP-NFP-15 H field probe
15 mm diameter, female SMA connector
TP-NFP-5 H field probe
9 mm diameter, female SMA connector
TP-NFP-E9 E field probe
2 mm tip, female SMA connector
TP-3P-15 tripod
up to 18 cm high
Antenna cable TP-BNC-SMA-200
flexible, 200 cm long, female SMA connector to BNC connector
Antenna cable TP-SMA-20
semi flexible, 20 cm long, male SMA connector to male SMA
connector
Grounded 50 Ohm BNC terminator TP-BNC-T50G
BNC to BNC, 5 cm ground lead with 2 mm banana plug
TP-Wrench89 wrench
8 and 9 mm hex nut wrench
2EMI probe set TP-EMI-HS6

Connecting the probes
To connect a probe to the instrument with option E, first place the TP-BNC-T50G
grounded terminator at the Ch1 input of the scope. When using a Handyscope
HS6 DIFF-1000 or WiFiScope WS6 DIFF-1000, make sure to connect the extra
ground lead to the grounding terminal next to the Ch1 input. When using a Handy-
scope HS6-1000 or WiFiScope WS6-1000, the extra ground lead is not required
and can be left unconnected.
Next connect the BNC connector of the TP-BNC-SMA-200 flexible antenna cable to
the grounded terminator. Insert the female SMA connector of the TP-BNC-SMA-
200 through the ring of the TP-3P-15 tripod, from the side with the recessed hex
shape.
Connect the male SMA connector of one end of the TP-SMA-20 semi flexible an-
tenana cable to the flexible antenna cable. Use the supplied 8 mm wrench to
tighten the nut to avoid the semi flexible cable to rotate. Do not over tighten,
maximum torque is 0.3 - 0.6 Nm (3 - 5 in lbf). Finally, connect the required probe
to the other end of the semi flexible antenna cable. Using the semi flexible cable
and the tripod, the probe can be positioned at the exact location near the test
subject.
EMI probe set TP-EMI-HS6 3

In the Multi Channel software, select an EMI Quick Setup to setup the instrument
and software properly for performing the EMI pre compliance test measurements.
Please note that when using the Handyscope HS6 DIFF-1000 or WiFiScope WS6
DIFF-1000, the EMI Quick Setups enable SafeGround for Channel 1, in order to
measure single ended. However, due to the extra grounding connection, the
SafeGround protection feature for channel 1 will be disabled, so there will be no
protection against short circuits to ground on channel 1. For the other channels,
the SafeGround protection remains available.
TiePie engineering
Koperslagersstraat 37
8601 WL Sneek
The Netherlands
Tel.: [phone]
Fax: [phone]
E-mail: [email protected]
www.tiepie.com
This information is subject to change without notice.
Copyright © 2021 TiePie engineering. All rights reserved. Revision 1.3, May, 2021.
4EMI probe set TP-EMI-HS6