Timago FS 692 User manual

1
INSTRUCTIONS FOR USE
Transport commode chair
Product code: FS 692
1. Characteristics
Transport commode chair is made of powder coated steel frame. Flip-
up armrests facilitate patients with considerably reduced mobility
getting in and out the chair. The chair is equipped with soft seat which
is upholstered with waterproof and easy to clean material, four swivel
castors, the rear of which have locks, swing away footrests, and toilet
bucket. Owing to the structure of the chair, it is possible to slide onto
the toilet.
The set includes:
•Frame
•Seat
•Backrest
•Right footrest with footplate
•Left footrest with footplate
•Protective strap
•Key for height adjustment
of footrests
•Toilet bucket with lid
Elements of the wheelchair:
a. Locking clips of the frame
b. Seat
c. Armrest
d. Locking pin
e. Footrest
f. Assembly pin of the footrest
g. Castor lock
h. Toilet bucket

2
2. Application
Transport commode chair is designed for people who have problems
with unassisted moving and for patients with dysfunctions and reduced
mobility. The chair is suitable for indoor use only. The chair can be
handled only with the help of an accompanying person.
The chair functions as a transport-toilet chair owing to the toilet bucket
located under the seat and four swivel castors. It facilitates the user
everyday hygiene. The chair is especially recommended to people who
have problems with mobility which are caused by:
•paralysis
•overweight or abnormal underweight
•degenerations or deformity of limbs
•degenerations or joints injuries
•limbs injuries or amputations
•heart and blood vessels disease, circulatory disorders
3. Assembly
Step 1. Remove locking clips which are located on the frame of the
backrest.
Step 2. Slide the backrest tubes into the two rear parts of the main
frame and lock the backrest with locking clips.
Step 3. Assemble the armrest in the front part of the frame by pressing
locking pins.
Step 4. Assemble the right and the left footrest in the front part of the
frame by placing them on two pins and turn them inwards until they
are locked.
Step 5. Assemble and adjust the protective strap on the footrest.
Step 6. From the back slide the toilet bucket without the lid into the
rails which are located under the seat. (Check the correctness of the
assembled toilet bucket).
The wheelchair is ready to use.

3
WHEELCHAIR HANDLING
•Check the condition of the castor lock, construction and tyres.
Check also the correctness of the assembled components and
their adjustment.
•Before using, make sure that the chair width (45 cm) matches to
the user, as the chair is not equipped with width adjustment.
•The chair is designed to be used only on short distances inside the
rooms. The chair does not have shock absorber so that long usage
is not recommended.
Note! Do not use the chair if any defects or deficiency are noticed.
FLIP-UP FUNCTION OF ARMRESTS
•Press the locking pin, remove the front part of the armrest from
the lock, and move it downwards.
•To close the armrest, move it upwards until the locking button
clicks.
•Do not use the armrest as a support while standing up. If required
ask the third person for help.
BRAKES
•To lock the castors, press the lever of the right and left lock with
foot. To release the castor, pull the lever upwards with foot.
FOOTRESTS
•The footplates should be in vertical position when getting in or
out the wheelchair. Do not use the footplates as a support while
getting in or out the wheelchair due to the risk of wheelchair
tipping over and falling.
GETTING IN THE WHEELCHAIR
•While getting in or out the wheelchair, changing the user’s
position or stop, the castors must be absolutely.

4
•The wheelchair should be located at the place of changing the
seat as close as possible. The wheelchair should touch the bed or
other seat being used, rear castor and front element of the frame.
If the user cannot change his/her seat independently, transfer the
user to the wheelchair.
•The user should sit as deep as possible in the middle of the seat in
order to avoid chair instability.
4. Technical data
Overall width
55 cm
Inner width
45 cm
Overall depth
87 cm
Seat height from the
ground
53 cm
Overall height
95 cm
Seat dimensions
44 x 44 cm
Weight
10.60 kg
Maximum capacity
100 kg
Folded width
55 cm
Frame color
red
5. Notes
Timago International Group does not bear responsibility of improper
moving in the commode chair, failure to comply safety regulations
and misuse.
6. Cleaning and maintenance
Carry out the maintenance of the wheelchair components regularly:
•The upholstery and the cushion can be cleaned with damp (not
wet) cloth and cold or warm water, without the use of detergents.
Difficult stains can be cleaned with a sponge. Do not soak the
upholstery too much. Dry away from heat sources.

5
•Plastic elements should be cleaned with damp cloth possibly with
the use of appropriate detergents for plastic elements. In such
case follow the instructions given by the producer and safety
measures.
•Empty and disinfect the toilet bucket and toilet seat after each
use. Use cleaning agents according to producer’s
recommendations.
7. Storage and transport conditions
Device should not be exposed to direct sunlight, water or moisture.
8. Warranty information
All products distributed by our company are covered by a warranty, the
terms of which are described in the warranty card available on our
website. Please contact the retailer from whom you purchased the
product. Please, keep in mind that for warranty purposes, the proof of
purchase (receipt or invoice) should be retained
9. Labels
Reference
number
Manufacturer
LOT number Manufacture date
Serial number Medical device
Note
Please read the
instruction
The manufacturer checked for compliance with
essential medical devices requirements.

6
Our complete line of products is available from our distributors.
Learn more at: www.timago.com. Thank you for choosing Timago!
Timago International Group
Spółka z o.o. i Spółka – Spółka komandytowa
ul. Karpacka 24/12
43-316 Bielsko-Biała, Polska
T.: [phone]
F.: [phone]
E.: [e-mail]
Rev. II, date 20.05.2021