Vivo DESK-V133E User manual

Black Electric Multi Motor Corner Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v133e
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: DESK-V133E

2 3
J (x1)
Power Cord
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
PACKAGE CONTENTS
TOOLS
NEEDED
330lbs
(149.69kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
WARNING!
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
A (x1)
Telescopic
Crossbar
D(x3)
Foot
F(x3)
Liing Column
S-A (x32)
M6x12 Bolt
S-B x15)
7/8" Screw
S-C (x2)
3/4" Screw
H (x1)
Control Unit
B (x1)
Extension
Crossbar
G(x1)
Fixing Plate
I(x2)
Hook
K (x1)
Extension Cord
E(x1)
Cable Tray
C(x3)
Side Bracket
S-D (x6)
M4x6 Bolt
S-E x3)
Cable Clip
S-F (x13)
Rubber Pad
Drill
Level
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
L (x1)
Control Panel
S-G (x1)
Allen
Wrench
STEP 2
Attach the two side brackets (C) to the two ends of the telescopic crossbar (A) using four M6x12 bolts
(S-A) as shown. Attach the last side bracket to the end of the extension crossbar (B) opposite from
the L-shaped bracket using two M6x12 bolts as shown. Tighten all bolts with Allen wrench (S-G).
Place liing columns (F) on telescopic crossbar (A), and align the holes on the end of the extension
crossbar with the holes on the center liing column and telescopic crossbar (A). Secure liing col-
umns and extension crossbar with ten M6x12 bolts (S-A). (NOTE: Two of the bolts insert through the
side of the L-shaped bracket on the extension crossbar.) Attach third liing column to the assembled
frame by using four M6x12 bolts (S-A). Tighten all fourteen bolts with the Allen wrench (S-G).
Loosen all eight set screws
on the telescopic crossbar (A)
and all four set screws on the
extension crossbar (B) using
the Allen wrench (S-G).

4 5
STEP 3 STEP 6
STEP 5
STEP 4
STEP 7
STEP 8
Place tabletop upside down on the floor.
Place frame assembly upside down on
tabletop, and adjust the crossbars to the
appropriate length.
Tighten all set screws with the Allen wrench (S-G).
Using the side brackets (C) as a guide, drill pilot holes into the tabletop
using a 3/32” drill bit.
Place the feet (D) on the columns as shown.
Insert M6x12 bolts (S-A) into the four
mounting holes on each foot and tighten
with Allen wrench (S-G).
Attach the fixing plate (G) to the frame using M4x6
bolts (S-D). Tighten all screws with screwdriver.
Connect control panel (L), liing columns (F) and
power cord (J) to the control unit (H). If needed,
use the extension cord (K) to connect the farthest
liing column.

6 7
STEP 9
STEP 10
STEP 12
STEP 11
Slide the control unit (H) onto the fixing plate (G).Attach the control panel (L) to the frame using the 3/4” screws
(S-C). Add the cable clips (S-E) to organize cables if needed.
Fix the hooks (I) to the shelf (E) with M4x6 bolts (S-D).
Tighten all bolts. Hang the cable management shelf onto
the frame as shown. Tighten thumbscrews on the hooks to
secure the shelf.
Remove the protective films from the adhesive rubber pads (S-F). Stick the rubber pads to the desk
frame, then place the tabletop on the desk frame. Attach the tabletop using the 7/8” screws (S-B).
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk weight limit. Keep area of vertical motion free of
obstacles.
Keep weight on desk balanced for
correct operation and longer life of
components.
Leave enough slack in cables to
allow for full range of vertical
motion.

Last Updated: 08/08/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654