Titan TI-Pandora User manual

TI - Pandora
Instruction Manual

1-2
3
4
5
6
7
8-9
10-11
12
13
14-17
18
19
20
21
ISEDC warning
Control Buttons on the side panel

Keep Dry – Do not operate in a wet or moist condition.
1

2

3

4
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .

5
This device complies with Innovation, Science, and Economic Development
Canad licence-exempt RSS standard(s). Operation is subject to the following
two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d' Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts
de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
The device is compliance with RF exposure guidelines, users can obtain Canadian
information on RF exposure and compliance.
Le présent appareil est conforme
Après examen de ce matériel aux conformité ou aux limites d’intensité de champ RF,
les utilisateurs peuvent sur l’exposition aux radiofréquences et la conformité and
compliance d’acquérir les informations correspondantes.
ISEDC warning

6
4
4

7

8
This model is come with 2 boxes packing design : Box 1 contains main body and Box 2
contains footrest.
Connect the cable to outlet and chair .Switch ON the current,the chair will return back
to the original position.(Caution:the assembly for footrest will be easy after the chair had
returned to original position.Unplug the cable after the chaire return to original position)
Connect the wire connectors and screw the cap tight.Then connect the air hose.
Caution:after the wire connector have been connected the cap must be screwed tight.
1.PREPARATION
2.Footrest assemble

9
2.Remove the two circlips on the bolts,then attach the footrest onto the base and
lock the circlips.
Caution:please attach on the long bolt first.
2.Connect the chair to a power supply
turn on the power switch,the chair will
be ready to start.
2.Zip the zipper between the seat pad
and footrest.

10

11

CLASSIC WAKE UP EXTEND
REVITALIZE STRETCH RETRACT
VIBRATESHOULDER ARM FOOT AIR
UPRIGHTRECLINE UP DOWN
SPEED MANUAL INTENSITY WIDTH
12
1.Power 2.Pause
3/4.Spot/Zone
7.Time
9.Wake up
10.Classic
12.Revitalize
15.Arm
16.Shoulder
19.Recline
20.Upright
21.Up
22.Down
5/6. -/+
8.Zero Gravity
11.Stretch
13.Extend
14.Retract
17.Foot Air
18.Vibrate
23.Speed
24.Manual
25.Intensity
26.Width
Controller

13
Remark:the blue tooth button will light when the blue tooth is open,then remote
will show blue tooth icon.
Wireless charging
USB charging
Intensity adjustment
Blue tooth Footrest massage
Auto program
Position adjustment
Heating

14
How to Start
Function Description
1.Power
• The power button starts and stops all functions on the massage chair.
• Press once, the chair is idle mode.
• Press again, all functions will stop, and massage rollers will return to original position.
2.Pause
• The pause button will allow all massage functions to stop temporarily.
• Press once, all the massage functions and timer will be stopped temporarily.
• Press again to resume the massage session.
3.Spot
• This key with two functions: one is for spot massage and one is for making roller upward.
• Press once, it will allow users to choose the exact position to massage.
• Hold the key and don’t release, it will move roller upward. When the roller reach the
position needed, stop holding the key.
• This can be applied to all massage selections.
4.Zone
• This key with two functions: one is for zone massage and one is for making roller
downward.
• Press once, it will allow uses to limit the massage in 12cm long to a particular body
zone.
• Hold the key and don’t release, it will move roller downward. When the roller reach the
position needed, stop holding the key.
5/6.-/+
• Press each time to adjust intensity of Kneading Massage.

15
7.Time
• The timer button controls the length of the massage session.
• The default time for all massage functions is 15 minutes.
• Press each time to change the length of the time in the following sequence:
20>25>30>5>10>15.
8.Zero Gravity
• Adjust the angle of the massage chair to zero gravity position.
Press to achieve position required.Press again to resume to original position.
9.Wake up
• Engages the Snooze Auto Program, based on the waist by Kneading, Shiatsu and other
techniques.
• Help to shape up body and relieve stress.
10. Classic
• Engages the deep tissue massage to loosen up the muscles.
11.Stretch
• This function allows users to adjust the strength of massage.
• There are total 5 levels for your options.
12.Revitalize
• This program focuses on neck, shoulder and hip by Rolling and Kneading, reduction of
body fatigue.
13/14.Extend/Retract
• These buttons control the footrest extension.
• Press once and the footrest will start to extend/retract.
• ·Press again to stop the footrest at your preferred length.

16
15.Arm
• This function activated the air compression on arm area.
16.Shoulder
• This function activated the air compression on shoulder area.
17.Foot Air
• This function activated the air compression on foot area.
18.Vibrate
• This button control the vibration in seat area.
Press once to activate vibration.Press again to stop the vibration.
19.Recline
• This button controls recline angle of the massaging chair.
• Press once, the backrest and footrest will move to a horizontal reclining position.
20.Upright
• This button control incline angle of the massage chair.
• Press once, the backrest and footrest will move to an upright sitting.
• Press again to stop the product at your preferred angle.
21.Up
• Adjust back massage position.
Press the button to choose position of massage rollers when a "beep" sound alerts in
10 seconds.
Release the button once the desired position is achieved.

17
22.Down
• Adjust back massage position.
Press the button to choose position of massage rollers when a "beep" sound alerts in
10 seconds.
Release the button once the desired position is achieved.
23.Speed
• Control the speed of Tapping, Kneading, Swedish, Shiatsu, Kneading and tapping
massage.
• Select a massage function and press to select between 5 speeds.
24.Manual
• Controls Kneading, Tapping, Swedish, Shiatsu, Kneading and tapping ,Rolling massage.
• Press once to activate kneading massage of the full back.
• Each press of button, the massage mode changes in sequence: Tapping>Swedish>
Shiatsu>Kneading and Tapping>Rolling.
25.Intensity
• This button allows users to adjust the intensity of airbag on the calves and feet area.
• There are five levels for your option.
26.Width
• This button allows you to control the width of the rollers.
• Select a massage function and press to adjust between Narrow, Normal and Wide
widths.

18