TOP VEHICLE TECH KWHON1 User manual

www.topvehicletech.com
The informaon provided in this document is subject to change without noce due to changes and/or
improvements to the product/s.
V1.0321
KWHON1
INSTALLATION MANUAL
This dash image is a visual representaon for display purposes only.
HONDA CIVIC

2006-2011

2
www.topvehicletech.com

The KWHON1 installaon kit allows for the retenon of the vehicle’s steering wheel controls and helps maintain
the original aesthec of the interior when installing a new car stereo. The KWHON1 gives you everything you
need for a complete install in one box. The components of this kit are compable for the Honda Civic
(Hatchback, 2006-2011) with basic, non-nav factory stereos. The wiring harness and interface will retain the
steering wheel controls and original me/date vehicle sengs. It features a factory amp turn on wire and also
helps retain original climate control buon funconality (if vehicle is equipped).
The interface supplied features a Honda OEM specic connector.


Installaons should be carried out by, or under the guidance of an experienced installer. If you do encounter any
problems during the installaon of this product, then please contact our dedicated customer service team at:
Phone: [phone] E-Mail: 

• 1x Fascia plate (with accessories)
• 1x Instrucon manual
• 1x Steering wheel control harness and interface
• 1x Antenna adapter
• 1x DAB antenna adapter
• 1x Stereo patch lead

3
www.topvehicletech.com

4. Unclip the top plasc panel just below the display with a panel removal tool.
1. Open the passenger side door and proceed to pull away the door trim from the pillar.


2. Using a set of panel removal tools, begin to pry away the pillar casing.
4. The DAB antenna not only has a self adhesive backing, but also features a black earth sheet. When
placing the DAB antenna, the earth sheet  be placed onto the metal part of the pillar. The antenna
itself must be located roughly 15cm from the top of the windscreen.


5. Once happy with the placement, take the 3m of wiring extension and feed it down through to the
stereo’s opening. With the wiring adjusted to the appropriate length, feel free to re-install the glovebox.
3. The glovebox will need to be dropped down to route the antennas wiring. To do this simply open the
glovebox and push both sides in. At the same me, pull the drawer out of place and leave in the footwell.

1. Once you have taken the main fascia panel o, you will need to transfer the air vents to the new fascia.
To do this you will need to disengage the clips of each vent as well as a screw on either side. When free,
simply re-locate onto the new fascia.
5. Removing the top panel will uncover 3x screw atop the fascia panel, these will now need to be removed.
6. Once the screws are out of the way, rmly pull the fascia panel with head unit out of the dashboard and
disconnect the wiring in the process.
2. Take the old fascia in hand and unscrew the hazard switch housing. When free, re-locate this to the
corresponding space on the new fascia.
3. Aach the brackets to either side of the radio. When aached, roughly test t the radio and bracket
combinaon in relaon to the new fascia, doing this, you can best measure whether the brackets need
moving forwards/backwards.
4. With the bracketry aligned, go ahead and push the fascia panel into place, connecng the hazard switch
in the process. When the “Stereo Installaon” process is complete, you can then simply feed the stereo
through the fascia’s opening and place the trim in front of the unit.
1. Remove the screws that surround the centre console and pull it up and out, disconnecng the cigaree
lighter in the process.
2. Lever the drivers side panel and undo 1x screw inside. When this is done, take a panel removal tool to
the steering wheel surround and just clip out of place to allow room for moving the fascia panel.
3. Using the aide of a panel tool again, remove the gear shier panel, this will allow you access to the 2x
screws underneath the head unit that will need to be removed.

4
www.topvehicletech.com

7. Aach the addional wiring on the harness to the back of the stereo:
- Speed Pulse  - Amp Remote Turn On
8. When all the above wires (and any addional accessories) have been connected, nally make the
connecons between the stereo and the vehicles pre-exisng power/stalk connectors.
5. Aach the 5-pin connector from steering wheel harness to vehicles pre-exisng air-con data connector.
2. Connect the bullet connector from the stereo patch lead to the ‘steering wheel remote input’ on the
back of the new stereo.
3. Connect the DAB antenna’s SMB connector to the back of the new stereo.
4. Aach the antenna adapter to the vehicles pre-exisng connecon and the back of new stereo.
6. Aach the 10-pin connector from steering wheel harness to vehicles pre-exisng display data connector.
1. Take the steering wheel control interface in hand and connect both the 12-way stereo patch lead and
the 14-way steering wheel harness connectors to the corresponding sides.


5
www.topvehicletech.com
Please note: conguraon layout may dier dependent on vehicle model.

MODEVOLCH
+
-
1
2
3
4
5
1. Track +
2. Track -
3. Volume +
4. Volume -
5. Source
1. Track +
2. Track -
3. Volume +
4. Volume -
5. Mode
 
1. Press and hold Mode  to enter the clock seng menu.
2. Press Volume +/- to toggle between hour, minute, month and year.
3. To change the value, press Track +/- .
4. Once the me & date has been set, press and hold Mode to exit the clock seng menu.


6
www.topvehicletech.com

ISO Connector
Connect to new stereo
OEM Specific Connector [17 Pin]
Connect to power/speaker connector from vehicle
Stereo Patch Lead Connector [12 Pin]
Connect to Interface Box
Note: Must be connected first, before power
connection is made to the interface
Main Wiring Loom Connector [14 Pin]
Connect to Interface Box
Interface Box
Flying Wires
Pink - Speed Pulse
Blue- Amp Remote Turn On
Stereo Patch Lead Bullet Connector
Connect to ‘Steering Wheel Remote Input’ on back
of the stereo.
OEM Specific Connector
[20 Pin]
Connect to relevant
connector from vehicle
Green Display Connector
[10 Pin]
Connect to relevant
connector from vehicle
Green Aircon Data Connector [5 Pin]
Connect to relevant connector from vehicle

7
www.topvehicletech.com


8
www.topvehicletech.com
If at any point you experience any problems and need any assistance before, during or aer the
installaon process, please contact us via :
Phone: [phone]
E-Mail: 
Mon - Fri 9am - 5.30pm GMT

If you would like to download a digital copy of this manual, or any other product, then please
visit the www.topvehicletech.com website.
This manual is considered correct at the me of prinng but is subject to change. For the latest
manuals & updates, refer to our website.
Copyright 2021 by TopVehicleTech.
All rights reserved. No part of this publicaon may be reproduced, distributed or transmied
in any form or by any means, including photocopying, recording, copying or other electronic or
mechanical methods, without the prior wrien permission of the author.