TOP VEHICLE TECH GRKRT02 User manual

www.topvehicletech.com
The informaon provided in this document is subject to change without noce due to changes and/or
improvements to the product/s.
V1.0522
GRKRT02
RENAULT TRAFIC
2014-2017
INSTALLATION MANUAL
This dash image is a visual representaon for display purposes only.

2
www.topvehicletech.com
ABOUT THIS PRODUCT
The GRKRT02 installaon kit allows for the retenon of the vehicle’s steering wheel controls and helps maintain
the original aesthec of the interior when installing a new car stereo. The GRKRT02 gives you everything you
need for a complete install in one box. The components of this kit are compable for the Renault Trac (2014-
2017) with Visteon stereos. The wiring harness and interface will retain the steering wheel controls and phone
buon funconality (if vehicle is equipped). The interface supplied features an OEM specic connector.
CUSTOMER SUPPORT
Installaons should be carried out by, or under the guidance of an experienced installer. If you do encounter any
problems during the installaon of this product, then please contact our dedicated customer service team at:
Phone: [phone] E-Mail: [e-mail]
CONTENTS
• 1x Fascia plate (with accessories)
• 1x Instrucon manual
• 1x Steering wheel control harness and interface
• 1x Antenna adapter
• 1x Stereo patch lead

3
www.topvehicletech.com
FITTING GUIDE
STEREO REMOVAL
FASCIA PLATE SET-UP
1. Take the brackets that come within the kit and aach them to the corresponding sides of the new
stereo.
2. With the brackets aached, roughly test t into the dashboard and place the new fascia over top. Doing
this, you can measure whether the brackets need moving forward/backward.
3. With the bracketry aligned, and the “Stereo Installaon” process complete, you can then install the
stereo into the dashboard using the pre-exisng screws, and place the new fascia over top to complete the
installaon.
1. Use a panel removal tool to remove the main fascia panel from around the main head unit.
2. Remove the 2x screws that hold the main head unit into place. Once free, pull out of the dashboard and
disconnect all of the wiring.

4
www.topvehicletech.com
FITTING GUIDE
5. When all the above wires (and any addional accessories) have been connected, nally make the power
connecons between the stereo and the vehicles pre-exisng connector.
1. Dependent on the style of steering wheel controls you will need to open the interface box and set the
dipswitches. For more informaon see overleaf.
4. Aach the antenna adapter to the vehicles pre-exisng connecon and the back of new stereo.
2. Take the steering wheel control interface and aach the 14-way steering wheel harness connector to
the relevant side.
STEREO INSTALLATION
3. Make a cut within the orange and purple loops on the back of the patch lead connector. Then proceed
to aach ‘Key 1’ to the light blue ‘SWC Remote’ wire on the stereo. When done, connect the 12-way
connector to the steering wheel control interface.

5
www.topvehicletech.com
Please note: conguraon layout may dier dependent on vehicle model.
STEERING WHEEL CONTROL FUNCTIONALITY
1
2
3
SRC
Front
Back 5
4
VOL +
VOL -
SOURCE
1
2
3
4
6
5
1. Volume +
2. Volume -
1&2. Mute (both pressed)
3. Source
4. Source (DIP 2: OFF)
Pick Up (Short Press)/Hang Up (Long Press) (DIP 2: ON)
5. Track +/-
1. Volume +
2. Volume -
3. Source
4. Pick Up/Hang Up
5. Track +/-
Original Buon New Funcon
Dependent on the style of steering wheel controls, you are able to alter Dipswitch 1 and/or 2 to re-adjust
signals to the stalk controls. Please note: when changing these dipswitches, the interface will need a CAN
power cycle before the change takes eect, so it is recommended that you disconnect the interface whilst
doing this process.
SETTING THE DIPSWITCHES
STYLE A STYLE B
STYLE A
1. Volume +
2. Volume -
3. Mute (DIP 1: ON)
Pick Up (Short Press)/Hang Up (Long Press) (DIP 1: OFF)
4. Source
5. Source (DIP 2: OFF)
Pick Up (Short Press)/Hang Up (Long Press) (DIP 2: ON)
6. Track +/-
1. Volume +
2. Volume -
3. Mute
4. Source
5. Source
6. Track +/-
Original Buon New Funcon
STYLE A

6
www.topvehicletech.com
WIRING DIAGRAM
ISO Connector
Connect to new stereo
OEM Specific Connectors [20 & 32 Pin]
Connect to relevant connectors from vehicle
Stereo Connection (Patch)
Lead Connector [12 Pin]
Connect to Interface Box
Note: Must be connected
first, before power connection
is made to the interface.
Main Wiring Loom Connector
[14 Pin]
Connect to Interface Box
Interface Box

7
www.topvehicletech.com
NOTES

8
www.topvehicletech.com
If at any point you experience any problems and need any assistance before, during or aer the
installaon process, please contact us via :
Phone: [phone]
E-Mail: [e-mail]
Mon - Fri 9am - 5.30pm GMT
TECHNICAL ASSISTANCE
If you would like to download a digital copy of this manual, or any other product, then please
visit the www.topvehicletech.com website.
This manual is considered correct at the me of prinng but is subject to change. For the latest
manuals & updates, refer to our website.
Copyright 2022 by TopVehicleTech.
All rights reserved. No part of this publicaon may be reproduced, distributed or transmied
in any form or by any means, including photocopying, recording, copying or other electronic or
mechanical methods, without the prior wrien permission of the author.