TOP VEHICLE TECH KWPOR4 User manual

www.topvehicletech.com
The informaon provided in this document is subject to change without noce due to changes and/or
improvements to the product/s.
This dash image is a visual representaon for display purposes only.
V1.0421
KWPOR4
INSTALLATION MANUAL
PORSCHE
PANAMERA


2
www.topvehicletech.com
ABOUT THIS PRODUCT
The KWPOR4 installaon kit allows for the retenon of the vehicle’s steering wheel controls and maintains
the original aesthec of the interior when installing a new car stereo. The KWPOR4 gives you everything you
need for a complete install in one box. The components of this kit are compable for the Porsche Panamera
(2009-2016) with amplied PCM 3.1 stereos. The wiring harness and Infodapter interface will retain the steering
wheel controls and factory phone buons, vehicle sengs and Aux and USB retenon. It also aids in generang
parking sensor graphics for the new stereo and provides an input for both an OEM and aermarket reverse
camera (if applicable). Supplied with a Quadlock connector.
NB: this installaon kit is for amplied systems. Warning tones & parking sensor audio will sll be acve
through the rear/front speakers.
CUSTOMER SUPPORT
Installaons should be carried out by, or under the guidance of an experienced installer. If you do encounter any
problems during the installaon of this product, then please contact our dedicated customer service team at:
Phone: [phone] E-Mail: [e-mail]
CONTENTS
• 1x Fascia plate (with accessories)
• 1x Instrucon manual
• 1x Steering wheel control harness and Infodapter interface (with USB retenon lead)
• 1x Antenna adapter
• 1x DAB antenna adapter
• 1x Stereo patch lead

3
www.topvehicletech.com
FITTING GUIDE
1. Open the passenger side door and proceed to pull away the door trim from the pillar.
STEREO REMOVAL
DAB ANTENNA INSTALLATION
2. Using a set of panel removal tools, begin to pry away the pillar casing.
4. The DAB antenna not only has a self adhesive backing, but also features a black earth sheet. When
placing the DAB antenna, the earth sheet MUST be placed onto the metal part of the pillar. The antenna
itself must be located roughly 15cm from the top of the windscreen.
Note: this antenna must not be placed atop any kind of heang elements, this will interfere with the
antenna’s signal.
5. Once happy with the placement, take the 3m of wiring extension and feed it down through to the
stereo’s opening. With the wiring adjusted to the appropriate length, feel free to re-install the glovebox.
3. The glovebox will need to be opened/removed to route the antennas wiring.
1. Remove both the le and right air vents by using a at blade. You need to release 6x clips from the
inside of the vents: 2x le, 2x right, 1x top, 1x boom. These clips are holding the vents rmly into place.
Once out, disconnect the wiring.
3. Remove the 4x screws that secure the main stereo and remove whilst disconnecng the wiring.
FASCIA PLATE SET-UP
3. When happy with the alignment, and the “Stereo Installaon” process is complete, screw the stereo
into the dashboard using the pre-exisng screws. Then re-install the vents either side, re-connecng the
wiring in the process.
1. Aach the brackets to the new stereo using the screws within the kit. With the brackets aached, oer
the whole unit to the back of the fascia. With the correct depth, aach the brackets to the fascia.
2. Before removing the head unit, it is best to put gear shier in either ‘Drive’ or ‘4th’ gear to allow for
room when removing radio.
2. Secure the stereo to the fascia panel using the four star clips by pushing each clip onto a spoke located
on the rear of the fascia panel.

4
www.topvehicletech.com
FITTING GUIDE
STEREO INSTALLATION
12. Aach the addional wiring on the harness to the back of the stereo:
Pink - Speed Pulse Purple - Reverse Gear Green - Park Brake Blue - Amp Remote Grey - Mute
13. When all the above wires (and any addional accessories) have been connected, nally make the
connecons between the stereo and the vehicles pre-exisng power/stalk connectors.
2. Connect the bullet connector from the stereo patch lead to the ‘steering wheel remote input’ on the
back of the new stereo.
10. Connect the DAB antenna’s SMB connector to the back of the new stereo.
11. Aach the antenna adapter to the vehicles pre-exisng connecon and the back of new stereo.
1. Take the steering wheel control interface in hand and connect both the 12-way stereo patch lead and
the 14-way steering wheel harness connectors to the corresponding sides.
6. Connect the yellow RCA connector to from the camera extension to the reverse camera input of the
stereo.
To retain factory OEM reverse camera: aach the yellow female RCA from on the camera extension
harness to the male yellow RCA on the main wiring harness.
To add an aermarket reverse camera: aach the yellow female RCA from on the camera extension
harness to the male yellow RCA of the aermarket reverse camera.
7. Connect the USB retenon lead between the vehicles OEM connecon and the USB connecon from
the stereo.
8. Connect the Red/White RCA connectors labelled ‘AUX’ to the back of the new stereo.
5. Connect the 4-way connector on the camera extension harness to the interface.
BEFORE INSTALLATION - DIPSWITCHES
On this parcular interface are a set of dipswitches. These dipswitches have the following properes:
1: OFF - Kenwood. ON - Pioneer.
2: OFF - NTSC reversing camera (default). ON - PAL reversing camera.
3: Change from OFF to ON to ‘reset’ screen seng to factory default.
Note: during this procedure, the screen background will change to red and no sengs adjustments can be made.
4: Not Used.
3. Connect the 8-way molex connector on the harness to the amplier retenon interface.
4. Take the vehicles bre opc amplier connecon and aach this to the remaining port located on the
amplier retenon interface.
9. Connect the Red/White RCA connectors labelled ‘Speaker’ to the front line outputs on the back of the
new stereo.

5
www.topvehicletech.com
Please note: conguraon layout may dier dependent on vehicle model.
STEERING WHEEL CONTROL FUNCTIONALITY
12
3 4
5 6
7
1. Volume +/- (Scroll) 2. Instrument Cluster Navigaon
Mute (Short Press) 4. Instrument Cluster Navigaon
Enter Infodapter Menu (Long Press) 5. Pick Up
3. Programmable Funcon 6. Hang Up
(on both Short & Long Press)*
7. Source (Short Press) Voice Assist (Long Press)
STEERING WHEEL CONTROLS
1. Menu + / Menu - 2 - 7. Funcons as above.
Select Menu Item (Short Press)
Exit Infodapter Menu (Long Press)
STEERING WHEEL CONTROLS - IN INFODAPTER
1. Camera / Parking Graphics Toggle (Long Press)
STEERING WHEEL CONTROLS - IN PARKING MODE 
The diamond buon on the steering wheel can be programmed to perform specic radio funcons whilst
in the Infodapter menus on both a long and short press. Funcon opons include: Source, Track +, Track
+, DSC + and DSC -. To assign a funcon, enter the Infodapter menu and go to the ‘Preferences’ sub-menu.
Select the desired buon funcon against the ‘Diamond Short Press’ and ‘Diamond Long Press’ opons.
any radio funcon in the
OEM instrument cluster menu
NonePreferences
*PROGRAMMABLE BUTTON