TOP VEHICLE TECH KWAUDI5 User manual

www.topvehicletech.com
The informaon provided in this document is subject to change without noce due to changes and/or
improvements to the product/s.
V1.0321
KWAUDI5

2006-2014
INSTALLATION MANUAL
This dash image is a visual representaon for display purposes only.

2
www.topvehicletech.com
ABOUT THIS PRODUCT
The KWAUDI5 installaon kit allows for the retenon of the vehicle’s steering wheel controls and helps to main-
tain the original aesthec of the interior when installing a new car stereo. The KWAUDI5 gives you everything
you need for a complete install in one box. The components of this kit are compable for the Audi TT (8J,
2006-2014) with Concert, Chorus or Symphony factory stereos. The wiring harness and interface will retain the
steering wheel controls, factory phone buons and the BOSE amplied system (if vehicle is equipped). Supplied
with both ISO & Quadlock connectors.





Installaons should be carried out by, or under the guidance of an experienced installer. If you do encounter any
problems during the installaon of this product, then please contact our dedicated customer service team at:
Phone:  E-Mail: 

• 1x Fascia plate (with accessories)
• 1x Instrucon manual
• 1x Steering wheel control harness and interface
• 1x Antenna adapter
• 1x DAB antenna adapter
• 1x Stereo patch lead
• 2x Stereo removal keys

3
www.topvehicletech.com

1. Slot the stereo removal keys into the four corners of the stereo, when suciently placed, remove and
disconnect the original head unit.


1. Idenfy which stereo connector you will need - either Quadlock or Mini ISO ().
1. Open the passenger side door and proceed to pull away the door trim from the pillar.


2. Using a set of panel removal tools, begin to pry away the pillar casing.
4. The DAB antenna not only has a self adhesive backing, but also features a black earth sheet. When plac-
ing the DAB antenna, the earth sheet  be placed onto the metal part of the pillar. The antenna itself
must be located roughly 15cm from the top of the windscreen.


5. Once happy with the placement, take the 3m of wiring extension and feed it down through to the
stereo’s opening. With the wiring adjusted to the appropriate length, feel free to re-install the glovebox.
3. The glovebox will need to be dropped down to route the antennas wiring. To do this, use an 8mm socket
to undo 2x screws located at the boom of the glovebox, and 3x screws located just within the lip. Once
free, simply leave in the footwell.


1. Start by aaching the brackets to the new stereo. These brackets allow you to set the specic depth of
the unit in relaon to the fascia plate. Start by lining up the spacerson the inside of the plates
.
2. Aach the spacer and plate combinaon to the corresponding side of the stereo using the screws that
come with the stereo. Then simply slide the stereo into the radio cage.
3. Take the fascia in hand, and slide the cage through the front of the fascia. If the depth/alignment of the
stereo hangs out too much/is reccessed to far, use the radio removal keys to release the stereo
from the cage and repeat the process.
  
 

4
www.topvehicletech.com
Please note: conguraon layout may dier dependent on vehicle model.
2. Take the steering wheel control interface in hand and connect both the 12-way stereo patch lead and
the 14-way steering wheel harness connectors to the corresponding sides.
3. Connect the bullet connector from the stereo patch lead to the ‘steering wheel remote input’ on the
back of the new stereo.
4. Connect the antenna adapter to both the pre-exist-
ing vehicle conneconand to the back of the
new stereo . 
5. Connect the DAB antenna’s SMB connector to the back of the new stereo.

 CONT’D.
6. Aach the red & white RCA connectors from the stereo wiring harness to the new stereo.
7. Aach the addional wiring on the harness to the back of the stereo:
- Speed Pulse  - Park Brake  - Reverse  - Amp Remote*
*The blue wire is needed for vehicles where 12V amp remote is not located in the harness.
8. When all the above wires (and any addional accessories) have been connected, nally make the con-
necons between the stereo and the vehicles pre-exisng connector.

MODE
1
2
3
4
5
6
1. Track +
2. Track -
3. Volume +
4. Volume -
5. Mute
6. Pick Up (short press)/Hang Up (long press)
1. Track +
2. Track -
3. Volume +
4. Volume -
5. Mute
6. Speech
 

5
www.topvehicletech.com

ISO Connector
Connect to new stereo
Quadlock/Mini ISO Connector
Connect to relevant connector from vehicle
Stereo Patch Lead Connector [12 Pin]
Connect to Interface Box
Note: Must be connected first, before power
connection is made to the interface
Main Wiring Loom Connector [14 Pin]
Connect to Interface Box
Interface Box
White/Red RCA Connectors (AUX)
Connect to back of stereo
Flying Wires
Pink - Speed Pulse
Green - Park Brake
Purple - Reverse Gear
Blue- Amp Remote
AUX
Stereo Patch Lead Bullet Connector
Connect to ‘Steering Wheel Remote Input’ on back
of the stereo.

6
www.topvehicletech.com
If at any point you experience any problems and need any assistance before, during or aer the
installaon process, please contact us via :
Phone: 
E-Mail: 
Mon - Fri 9am - 5.30pm GMT

If you would like to download a digital copy of this manual, or any other product, then please
visit the www.topvehicletech.com website.
This manual is considered correct at the me of prinng but is subject to change. For the latest
manuals & updates, refer to our website.
Copyright 2021 by TopVehicleTech.
All rights reserved. No part of this publicaon may be reproduced, distributed or transmied
in any form or by any means, including photocopying, recording, copying or other electronic or
mechanical methods, without the prior wrien permission of the author.