Toro NO FOUND TMC-424E User manual

Adjust Time/Date .................................. 2
Set Season Adjust % Factor................ 2
Set Rain Delay....................................... 3
Manual Station Operations.................. 3
Manual Program Operations ............... 5
Set Station Run Time ........................... 6
Set Program Start Time........................ 7
Set Watering Day Schedule................. 8
Review Program Settings .................. 10
Alert Displays...................................... 11
Questions? Call Toro Customer Support @ 800-664-4740 or 951-688-9221
PREV NEXT
ON
OFF
%
TMC-424E Quick Reference Guide
TMC-424E Quick Reference Guide
English Español Français

1. Turn the Function Dial to
Current Time/Day .The hour
digits will begin flashing.
2. Adjust the display by pressing the
or button.
NOTE: Hold either button down for
rapid advance.
3. Press the button to select the
next field.
4. Repeat steps 2 and 3 to set the current
minutes, year, month and day (current
weekday will be set based on calendar
setting).
5. Return the Function Dial to RUN
when finished.
1. Set the Program Switch to select
program A,B,C,or D.
2. Turn Function Dial to Season Adjust .
3. Press the or button to adjust the
%value for the selected program.
NOTE: Adjusting the % value to Off
prevents operation of the program.
NOTE: A Season Adjust % factor over
100% will automatically split the adjust-
ed program run time in half and run a
repeat (back-to-back) program cycle.
4. Press the button to select Season
Adjust (for all programs) by month.
5. Press the or button to adjust
the % value.
Set Season Adjust % FactorAdjust Time/Date
2

NOTE: Adjusting the % value to Off
prevents operation of all programs for
the entire month.
NOTE: The %symbol will be displayed
to indicate when a Season Adjust %
factor is applied.
1. Turn the Function Dial to OFF .
2. Press the or button to select the
number of days to delay operation from
1to 14.
3. Turn the Function Dial to RUN .
NOTE: OFF and the number of rain
delay days remaining until automatic
operation resumes will be displayed.
Automatic operation will resume when
the delay day number is no longer
displayed.
4. To terminate the Rain Delay function,
turn the Function Dial to OFF .
5. Press the button until only OFF is
displayed.
6. Turn the Function Dial to RUN .
Set Rain Delay
3

IMPORTANT: True Manual operation
will override all flow-sensing
limits.True Manual Operation
1. Turn Function Dial to Manual Stations .
2. Press the button as needed to select
the station number.
3. Press the button to start the station.
ON will be displayed with the icon
(flashing).
NOTE: The station will run continuously
until any navigation button is pressed
or the Function Dial is turned. The station
will turn off automatically at Midnight if
left unattended.
Timed Manual Operation
1. Turn Function Dial to Manual Stations .
2. Press the button to select the station
number.
3. Press the or button to select a
manual run time (1 minute – 8 hours).
4. To select additional stations, repeat
steps 2 and 3.
5. When station selections have been
made, turn the Function Dial to RUN .
• The operating station number(s),
remaining station run time and icon
will begin alternating with the current
time of day.
• The stations will operate in the order
selected, either sequentially or
concurrently as determined by
the Stack/Overlap option selection.
Manual Station Operations
4

• Automatic mode will resume when the
manual operation has been completed.
• To advance through the station
sequence, press the button.
• To terminate manual operation at any
time, turn the Function Dial to OFF .
When the display stops flashing, return
the dial to RUN .
•Single Program Operation
1. Turn the Function Dial to
Manual Programs .
2. Set the Program Switch to select
program A,B,C,or D. The program
letter and MAN will be displayed. All
stations assigned to the program will
be indicated by solid circles.
3. Press the button to start the watering
cycle. The first station in sequence will
turn on. The program identifier and icon
will begin flashing.
4. Turn the Function Dial to RUN .
• The operating station number, remain-
ing station run time and the icon will
alternate with the current time of day.
• The stations will operate one at a time
in numeric sequence.
• Automatic mode will resume when the
manual operation is finished.
• To turn off an active station and start
the next station in sequence, position
Program Switch (if needed) to select
the program, then press the button.
• Toend manual operation at any time,
turn the Function Dial to OFF .
When the display to stops flashing, turn
the Function Dial to RUN .
Manual Program Operations
5

•Multiple Program Operation
1. Turn Function Dial to
Manual Programs .
2. Set the Program Switch to select pro-
gram A,B,C,or D.
3. Press the button to start the program
watering cycle. The program identifier
will begin flashing and Water On icon
will be displayed.
4. To select additional programs, repeat
steps 2 and 3.
5. Turn the Function Dial to RUN .
• The operating program identifier, station
number(s), remaining station run time
and icon will begin alternating with
the current time of day.
• The programs will operate in the order
selected, either sequentially or
concurrently as determined by the
Stack/Overlap option selection.
• Automatic mode will resume when
the manual operation is finished.
• To turn off an active station and start
the next station in sequence, position
Program Switch (if needed) to select
the program, then press the button.
• To end manual operation at any time,
turn the Function Dial to OFF .
When the display to stops flashing, turn
the Function Dial to RUN .
1. Set the Program Switch to select
program A,B,C,or D.
2. Turn Function Dial to Station Times .
3. Press the or button to select
the station number. The corresponding
station output terminal will be shown
on the display as a solid circle.
Set Station Run Time
6

4. Press the or button to adjust
the station run time from Off (-- -- --)to
8hours (in 1-minute increments).
If seconds format is enabled, station run
time can be set from 01–60 seconds.
NOTE: Hold either button down for
rapid advance.
5. Repeat steps 3 and 4 for all stations to
be assigned to the selected program.
1. Set the Program Switch to select
program A,B,C,or D.
2. Turn Function Dial to Start Times .
The hour digits will begin flashing.
3. Press the or button to select
astart time number (01 to 16).
NOTE: Any start time number currently
assigned to another program can not be
selected. If all 16 start time assignments
are in use, NONE will be displayed.
4. Press the or button to select a start
time hour (note the correct a.m./p.m.
designation in the 12-hour clock mode).
NOTE: Toremove a start time, select
-- --:-- -- (off), located between 11:00 p.m.
and 12:00 a.m. (00 minutes).
5. Press the button to select minutes
digits. Repeat step 4 to set start time
minutes (00–59).
6. Repeat steps 3–5 to set additional start
times for the selected program.
Set Program Start Time
7

Note: If the program has an Interval or
Odd/Even schedule currently set, it must
be removed first to select another format.
To Set Calendar Days:
1. Set the Program Switch to select
program A,B,C,or D.
2. Turn Function Dial Calendar Days .
3. Sunday will be displayed and selected
to water indicated by the water icon.
Toexclude the day from the schedule,
press the or button to display
the Watering Off icon.
3. Press the button to select the next day.
4. Repeat step 2 and 3 to schedule
the remaining days of the week.
To Set Odd or Even Days:
1. Set the Program Switch to select
program A,B,C,or D.
2. Turn the Function Dial to the
Odd/Even position.
3. Press the or button to select
ODD or EVEN.
4. To exclude specific days from watering,
press the button to select the day.
5. To exclude the day from the schedule,
press the or button to display
the Watering Off icon.
6. Toexclude additional days (7 maximum),
repeat steps 4 and 5.
Set Watering Day Schedule
8

To Set Interval Days:
1. Set the Program Switch to select
program A,B,C,or D.
2. Turn the Function Dial to the Interval
Days position.
3. The CYCLE LENGTH prompt and the
current Interval (01–31DAY or -- -- -- [Off])
will be displayed.
4. Press the or button to select the
Interval cycle length.
NOTE: The cycle length can be set from
01 (water every day) to 31 (water once
every 31 days). The Interval cycle starts
at 01 and increases by 1 digit each day.
The watering day occurs when the
selected Interval cycle length is reached.
Tospecify when the first watering day
will occur, the current day within the
Interval cycle must be selected.
For example, if a 04 DAY Interval is
entered and watering is to begin in one
day, select 03 as the Current Day.
5. To select the Current Day in the Interval
cycle, press the button to display the
CURRENT DAY prompt.
6. Press the or button to select the
value (01–selected Interval number).
7. To exclude specific days from watering
(7 maximum), press the button to
select the day.
8. To exclude the day from the schedule,
press the or button to display the
Watering Off icon.
9. Repeat steps 7 and 8 to continue
excluding days.
9

The Program Review feature provides a
convenient method of reviewing all
user-defined programming information.
Program elements are displayed as follows:
• Total program cycle duration, factored for
Season Adjust %, delays and repeats.
• Total irrigation time (time irrigation actu-
ally occurs), factored for Season Adjust
%, delays and repeats.
• Watering day schedule type (Calendar,
Odd/Even of Interval)
• Program start times
• Station run times
• Rain Sensor assignment by program
• All flow settings (when flow sensing
option is used).
1. Turn the Function Dial to Review .
2. Set the Program Switch to select the
program to be reviewed.
3. Press the button to index through
the program information.
4. When finished, turn the Function Dial
to RUN .
Review Program Settings
10