Toshiba OIS Series User manual

Contents
i
UMAN\OIS60\0603
Operator Interface Station
OIS60
USERS MANUAL
Setup and Operation
CONTENTS
For Toshiba T-Series
Programmable Logic Controllers
Toshiba International Corporation

Contents
ii
Preliminary
Thank you for purchasing OIS Series product from Toshiba International Corporation. OIS
Series Products are versatile operator interfaces with Microsoft Windows® based configuration
Software.
This manual will help you to safely install, configure and operate OIS60 Product.
All the safety warnings and precautions must be followed to ensure proper unit performance and personal
safety.
Warnings used in this manual:
DANGER Danger Warnings are used to indicate situations,
locations and conditions that can cause serious injury or
death.
CAUTION Caution Warnings are used to indicate situations and
conditions that can cause operator injury and/or unit
damage.
We hope that you find this manual informative. If additional information or technical assistance is
needed please contact:
Toshiba International Corporation
13131 W. Little York Road,
Houston TX 77041
Tel: [phone]
Fax: [phone]
Website: www.tic.toshiba.com
Email: [email protected]
Manual Revisions:
If you contact us in reference to this manual, please include the following document number:
Name: User manual For OIS60
Document: UMAN\OIS60\0603
Rev.: Rev 0
IMPORTANT
OIS Series Products are intended to be operator interfaces, to work with PLCs which
actually take control actions. It is assumed that the user is well acquainted with the PLC
system being used. Never use OIS units to perform emergency stop applications. It is
advised that separate switches be used outside the PLC for ANY emergency stops.
Any mechanical or electrical modification to this unit will
void all warranties.
N


Contents
iii
Table of Contents
1. Introduction 1
1.1 Purpose of this Manual 2
1.2 Introduction to OIS60 2
1.3 How OIS60 Works 3
1.4 OIS60 Specifications 6
2. Hardware 7
2.1 Installation Instructions 8
2.2 Power Requirements 9
2.3 Serial Port 10
2.4 PLC Port 10
3. Getting Started 11
3.1 Introduction 12
3.2 Application - Tags, Screens, Touch Screen keys and Tasks 12
3.3 PLC Communications 12
4. Understanding OIS Features 13
4.1 Screens 14
4.2 Alarms 20
4.3 Application Task-List 20
5. Configuration Software 23
5.1 Introduction to Configuration Software - OISetup32 24
5.2 Installing OISetup32 Software 24
5.3 OISetup32 Software Basic 25
5.3 Create New Application 31
5.4 Save and Download Application 51
6. Applications Examples 53
6.1 Installations and Setup 54
6.2 Define Node and Tags 55
6.3 Define Screens 57
6.4 Define Alarms 64
6.5 Define ApplicationTasks 65
6.6 Load Applications into OIS60 66
7. Frequently Asked Questions 67
7.1 How Do I ? 68

Contents
iv
8. Diagnostics and Maintenance 69
8.1 Diagnostics 70
8.2 Maintenance 71
Appendix v
A Cable Diagrams vi
B Order Numbers for OIS, Converters & Cables viii

Introduction
Page 1
1. INTRODUCTION
In this Chapter
Purpose of this Manual
Introduction to OIS60
How OIS60 works
OIS60 Specifications
Ø
Ø
Ø
Ø

Page 2
Introduction
1.1 Purpose of this Manual
The intention of this Operation Manual is to provide a guide for safe installation, configuration
and operation of OIS60. This manual is applicable for other OIS series models also.
Read this operation manual thoroughly before installing and operating OIS60
This document is based on information available at the time of its publication. While efforts have been
made to be accurate, the information in this document may not cover all the details or variations in
hardware or software. Features described herein may not be present in all hardware. Toshiba reserves
the right to update information in this publication without prior notice.
1.2 Introduction to OIS60
OIS Series operator interfaces provide man-machine interface to the PLC system. The OIS
communicates with the PLC using on its serial communications port.
Configuration of OIS:
Each OIS has to be configured using the OISetup32 Software before connecting it to the PLC.
OIS-IBM Cable
Normal Operation:
Connect OIS to PLC using the correct PLC-OIS cable and your OIS unit is running. OIS can
communicate with any RS232 and RS485 device without making any setting on the unit.
RUN
POWER
COMM
PLC
RUN
POWER
COMM
PLC To PLC Programming Port
PLC port
of unit
Connecting
Cable

Introduction
Page 3
1.3 How OIS60 Works
The OIS60 follows a specific sequence for performing the tasks defined by the user in the application.
The sequence is as shown below
Power-up
Message
PowerupTask
START
IBM
Comm
?
A
CompleteIBM
Communication
PLC
Comm
Error
?
Y
N
N
YRe-establishPLC
Communication
Re-Start
GlobalTask
CheckScreen
Number
N
Y
Same
Screen
Number
?
C
PerformAfterHiding
TaskforPrevious
Screen
Password
Protected
Screen
?
N
Y
D
B

Page 4
Introduction
Checkifsamekey
pressed
UploadAlarmBlock
ServAlarm
DisplayScreen
DisplayAssociatedScreens
ServWhileShowingTask
Y
N
KeyReleasetask
Samekey
Pressed
?
Loadnew
keys
I
Valid
Screen
password
?
N
Y
PerformBefore
ShowingTask List
fornewScreen
F
D
C
UploadTag Block
B

Introduction
Page 5
Y
N
New
key
Pressed
?
A
I
Y
N
ValidKey
Password
? A
ServKey
Press Task
Password
Protected
Key ?
Y
G
N
G
A

Page 6
Introduction
1.4 OIS60 Specifications
RUN
POWER
COMM
Power : 24V DC + 10%, 3W maximum
Display : 6” diagonal, 320x240 pixel, 256 color, CCFL Backlit (20,000Hrs at 25OC)
Bezel : IP 65 rated Touch Screen
Operating Temperature : 0OC to 50OC
Storage Temperature : -20OC to 80OC
Bezel Size : 139 mm x 197mm
Panel Cutout : 183.20 mm x 125.20 mm
Humidity : 10% to 90% (Non condensing)
Communication Ports : Two ports, one for connecting to the PLC and one for programming /
serial printing.
Immunity to ESD : Level 3 as per IEC1000-4-2
Immunity to Transients : Level 3 as per IEC1000-4-4
Radiated Susceptibility : Level 3 as per IEC1000-4-3
Emissions : EN55011 CISPR A
System Components:
- OIS60 unit with LCD display and Touch Screen.
- Power Supply connector.
- Installation Kit: Gasket, Six Mounting Clamps.
- OISetup32 Software Installer.
Note: User should order PLC / IBM cable separately.