Toshiba Combi control User manual

User manual
Snabbguide
Pikaopas
Hurtigstarts guide
Toshiba heat pump control by mobile phone

2
Contents 2
What Combi Control does? 4
Indicator lights 6
Buttons 8
Power 10
SIM card 10
Installing Combi Control 12
Testing Combi Control 17
Turning heat pump ON/OFF 18
Commands 20
User levels 22
Owner setup 24
Owner number reset 25
Setup reset 27
User setup 28
Multiple commands 29
Heat pump model setup 30
Alarm messages setup 32
Alarm messages 33
Error messages 34
Report messages 35
Combi Control command sheets 39
Get in touch with us 41
Om Combi Control 43
Indikationslampor 44
Knappar 46
Strömmatning 48
SIM-kort 48
Montering av Combi Control 50
Testkörning av Combi Control 55
Slå PÅ/AV värmepumpen via SMS 56
Kommandon 58
Användarnivåer 60
Inmatning av ägarnummer 62
Återställning av ägarnumret 63
Fabriksåterställning (hård RESET) 66
Inmatning av Användarenumret 67
Inmatning av värmepumpsmodell 68
Inställningar för larmmeddelanden 70
Larmmeddelanden 72
Felmeddelanden 73
Rapportmeddelanden 74
Hård RESET (fabriksåterställning) och
inmatning av Ägarnummer 78
Kontakta oss 80
ENG SWE

3
Mitä Combi Control tekee? 83
Merkkivalot 84
Painikkeet 86
Virta 88
SIM-kortti 88
Combi Controlin asennus 90
Combi Controlin testaus 95
Lämpöpumpun käynnistys/sammutus
96
Käskyt 98
Käyttäjätasot 100
Omistajan asettaminen 102
Omistajan numeron poistaminen 103
Asetuksien tyhjennys 105
Käyttäjän asettaminen 106
Useat eri käskyt 107
Lämpöpumpun mallin asetus 108
Hälytysviestin asetukset 110
Hälytysviestit 111
Virheviestit 112
Raporttiviestit 113
Combi Controlin käskyt 117
Ota yhteyttä 121
Hva gjør Combi Control? 123
Indikatorlys 124
Taster 126
Strøm 128
SIM-kort 128
Installering av Combi Control 130
Testing av Combi Control 135
Slå varmepumpe PÅ/AV 136
Kommandoer 138
Brukernivåer 140
Eierinnstillinger 142
Nullstilling av Eiernummer 143
Nullstilling av innstillinger 146
Brukerinnstillinger 147
Innstilling av varmepumpemodell 148
Innstilling av alarmmeldinger 150
Alarmmeldinger 151
Feilmeldinger 152
Rapportmeldinger 153
Combi Control kommandoark 157
Ta kontakt med oss 159
FIN NOK

4
What Combi Control does?
Combi Control is a heat pump controller you operate with a mobile phone.
It is compatible with all major manufacturers’ heat pumps and all mobile
phones (see Combicontrol.net for the complete list).
The easiest way to use Combi Control is with a Smartphone, using the
Combi Control app downloadable from the Android Market (for Android
phones ) or App Store (for iPhone). It can also be controlled with regular
mobile phone text messages (SMS). Combi Control allows you to have
long distance control over the mode of the pump, room temperature and
fan speed settings. Combi Control can also inform you about low room
temperature, power failures and heat pump service intervals.

5

6
Indicator lights
The controller has 3 LED indicators and 2 buttons
for easy setup. It has also 2 infrared LEDs that
transmit your commands to the heat pump.
LED 1 - Power
on switched on
blinking no power, working on battery
off switched off
LED 2 - GSM network LED
on restart time, SIM missing or SMS processing
1 blink (3 s interval) normal status
3 blinks (3 s interval) no signal from mobile phone
or not connected to a mobile network
blinking (500 ms interval) data call session is active
LED 3 - IR LED
blinking transmitting by IR

7
LED 1 - Power
LED 2 - GSM network LED
LED 3 - IR LED

8
Buttons
Use a straightened paper clip or something similar to push the recessed
buttons.
RESET button
Short push turns the controller off when working on battery
The controller has a battery that keeps it operational even if it’s
disconnected from a wall outlet. To fully turn off the controller, push the
RESET button. The 3 LED lights will blink for about a second and the
controller switches off.
Use this button also to clear the most recent settings (the Owner number
will remain unchanged).
TEST button
Short push turns the heat pump ON/OFF
Use the TEST button to confirm that the IR beam from the controller
reaches the heat pump.

9
RESET button
TEST button IR beam
NB! Pushing both buttons simultaneously for 3 seconds initiates the hard
reset: restores factory settings, deletes Owner number and heat pump
settings (same function as with command SMS “90”).

10
Power
When the power is out (power = 0V) the controller continues to work on
the battery and turns off after the battery’s voltage drops below 3.5V. A
fresh battery lasts for approximately 24 hours (note that over time the
battery’s capacity decreases). After the controller is turned off the run time
will be saved. To save battery life when the power is out the controller can
be turned off with a short push on the RESET button.
SIM card
NB! Make sure you disable the PIN code of the SIM card you use in Combi
Control.
NB! Make sure the SIM card you use in Combi Control can access 2G
network. Combi Control is not compatible with SIM cards that use only 3G
network.

11
A) Make sure that you have previously disabled the SIM card
PIN code. Insert SIM card as shown into Combi Control.
B) Plug the adapter into the socket under the Combi Control.
A B

12
Installing Combi Control
Combi Control should be mounted on the wall to the right of your heat
pump’s indoor unit (see fig. 1), with its IR transmitter pointing down. This
way
the IR beam is reflected from the floor and reaches the heat pump’s sensor
most efficiently.
Other mounting configurations are possible too
as long as IR transmission from the controller
to the pump works.
NB! Thick carpets and dark floors can distort the IR beam. Make sure the
IR beam reaches the pump’s sensor by using the controller’s Test function.

13
Fig. 1
On the right side of
the indoor unit
Fig. 2
Attached to the right side of
the indoor unit

14
Fig. 3
Beneath the indoor unit
Fig. 4
On the wall, opposite to
the indoor unit

15
Fig. 5
On a ledge, opposite to the
indoor unit

16
Fig. 6, 7
Do not place Combi Control
on the left side of the indoor
unit!
Indoor unit’s internal
condenser might block Combi
Control’s signal.

17
Testing Combi Control
To see if Combi Control can send commands to your heat pump, turn off
the pump and press the controller’s TEST button. When the connection is
established, Combi Control turns the pump on with its last settings and you
can proceed using the controller.

18
Turning heat pump
ON/OFF
SMS Command ON turns heat pump on.
SMS Command OFF turns heat pump off.

19
ON
sms: sms:
OFF
turns heat pump on turns heat pump off

20
Commands
The range of heat pump temperature values Combi Control controls is
16-30 °C (default +20 °C) and the fan speeds are AUTO, MIN, NORM, MAX
(the default is NORM).
After selecting a mode (AUTO, DRY, COOL, HEAT, T8, T8) heat pump is
turned on with 20 °C maximum temperature and normal fan speed, if not
assigned differently by the Owner or the Users.
The pump can be assigned different temperature and fan speed values
with Combi Control.
For example, the SMS: “COOL 19 MAX” orders the pump to cool until 19
°C and fan at maximum speed. When you change a heat pump function
Combi Control always responds with an SMS that reports its STATUS.