Toshiba 1000 Series User manual

TOSHIBA/HOUSTON INVERTER PLANT
DESIGN DATA D-UM0029 Page 1 of 4
SUBJECT: 1000 Series UPS Options – Frequency Conversion
RELATED DATA FILE NO.
COPY DRAWN BY: DATE:
TO: H. Huynh 10/2005
TO: CHECKED BY:
TO: MTA 10/2005
TO: APPROVED BY: DATE:
NO. REVISION DATE BY TO:
FOR AUTHORIZED SERVICE PERSONAL ONLY
Models: 1000 Series UPS
CAUTIONS
&
INSTALLATION INSTRUCTIONS
Cautions:
Any maintenance, additions, and/or changes that are to be done to this UPS should be
performed by a certified Toshiba trained repair technician authorized to service
Toshiba’s 1000 Series UPS.
The followings are a list of minimum safety requirements that should be adhered to,
and is not to be interpreted to be the only safety requirements to follow. Please follow
all Local, State, and Federal Safety Requirements.
1) Verify that the UPS is off and that the power cord or main power is disconnected from
the power source. (Observe Lock-out/Tag-out procedures if applicable)
2) Remove watches, rings, and/or other metal objects.
3) Use insulated tools to prevent inadvertent shorts.
4) Wear safety glasses, rubber gloves and boots.
5) Do not lay tools or metal parts on top of the batteries.
6) All connections must be made in accordance with National and Local Electric Codes.
In no event will Toshiba Corporation be responsible or liable for either indirect or
consequential damage or injury that may result from the modification of this unit.
Installation Instructions:

TOSHIBA/HOUSTON INVERTER PLANT
DESIGN DATA D-UM0029 Page 2 of 4
SUBJECT: 1000 Series UPS Options - Frequency Conversion
NO. REVISION DATE BY
FOR AUTHORIZED SERVICE PERSONAL ONLY
Install “FlashH08” Flash Program
There are two types of installation files for the Flash program. The one that is appropriate
for you can be determined by first checking the “CPU Version” that is displayed on the
LCD display in the front panel.
1.) If the format is XX.X
This means that the CPU is an R mask type. In this case you should run the
“Flash3062_R” program to install the “FlashH08” flash software. Further instructions on
configuration are explained below.
2) If the format is XX.XB
This means that the CPU is a B mask type. In this case you should run the “Flash3062_B”
program to install the “FlashH08” flash software. Further instructions on configuration are
explained below.
Use “FlashH08 ” to flash R mask type/B mask type CPU
1. To properly configure and utilize this software, terminate all applications that
occupy COM 1. (COM 1 is the default communication port for this software)
2. Connect the RS232 cable to the UPS from “COM1” of the PC.
3. Turn off the UPS, but keep the AC Line on. The proper procedure for this is
explained in the UPS manual that is included with the UPS.
4. Click on the appropriate “FlashH08” software that was installed in the previous
section.
i. If you installed the R mask type, it should be labeled “R Mask Flash” in the
title like the one shown below.

TOSHIBA/HOUSTON INVERTER PLANT
DESIGN DATA D-UM0029 Page 3 of 4
SUBJECT: 1000 Series UPS Options - Frequency Conversion
NO. REVISION DATE BY
FOR AUTHORIZED SERVICE PERSONAL ONLY
ii. If you installed the B mask type, it should be labeled “B Mask Flash” in the
title like the one shown below.
5. Click Load in the Menu bar to load the file (*.mot) that you want to reflash to the
CPU.
6. Click the ALL button in the Toolbar and it will display “Programming.”1,2 During
this period, both the LEDs labeled “Bypass_LED” and “On_LED” are turned on
for the tower UPS. For the Rackmount 1U, both the LEDs labeled “Inverter” and
“DC LOW” are lit.

TOSHIBA/HOUSTON INVERTER PLANT
DESIGN DATA D-UM0029 Page 4 of 4
SUBJECT: 1000 Series UPS Options - Frequency Conversion
NO. REVISION DATE BY
FOR AUTHORIZED SERVICE PERSONAL ONLY
Setup:
1. Make sure the UPS is off and the AC Line is on. The LCD screen should appear
blank.
2. Press and hold the function button for 1 second and release the button to enter the
front panel settings. Once in this mode, you can scroll through different settings
using the function button.
3. Look for the newly added software, “Freq Convert Set” and press Enter.
4. Once inside, you can change the output frequency by pressing the function button.
5. After choosing the correct frequency, press Enter to select it. Once selected, the
LCD will display a blank screen.
6. Turn on the UPS.
Note:
1If the communication fails during “Programming” for:
•R Mask – user should wait more than 35 seconds and then click the “W” button on
the Toolbar to start “Programming” again.
•B Mask – The LED labeled Alarmed_LED will be turned on. The user should wait
more than 10 seconds and then click the “W” button on the Toolbar to start
“Programming” again.
2Do not run any other application software on the PC during “Flash Process”, because the
“FlashH08” application uses up a large amount of the PCs resources.