Toto TBW01015 Series User manual

0G260G(C)
2023.03
Installation Manual
Before installing the product, please read the Installation
Manual carefully and keep it for future reference.
0G272G(B)
2023.07
After installation the manual must be kept by the customer.

1
1
2
3
4-7
8
9
TOTO Asia Oceania Pte. Ltd.
Telephone: [phone]
FAX: [phone]
Address: 10 Eunos Road 8 #12-07 Singapore Post Centre
Singapore 408600
Website: asia.toto.com
TOTO KOREA LTD.
: [phone]
FAX : [phone]
: 351-16 3
:
https://kr.toto.com/

2
1
2
2
1
1
1
1
TBW01015* 900mm
TBW01016* 600mm
TBW02011* 900mm
TBW02012* 600mm
8
Example: TBW01016* series shower holder
Figure 1 Shower holder installation
Shower holder installation
1. As shown in figure 1, try to assembly the slide type shower holder. Install properly the fixed rod,slide seat, wall
seat core, wall seat and decorating cover. (For specific assembly process, refer to step 3)
Wall seat
Wall seat core
Decorating cover
(without “TOTO” marking)
Straight fastening screw (having
been assembled in the fixed rod)
Tapping screw
(4× 4.2 × 30)
Expansion pipe
Fixed rod
Slide seat
Handle (facing upward
when being locked)
Knob
Wall seat core hole
(in vertical direction)
Plug cover (with O-ring)
Installation hole
Decorating cover
(with “TOTO” marking)
Mounting Paper
Attentions:
Do not scratch the plated surface in installation or disassembly.
Do not install reversely the slide seat. (The handle faces upward when the knob is
locked)
The wall seat core is in the vertical direction.
The decorating cover with “TOTO” marking is installed on the wall in the lower part.
2.Drill a hole at a proper location on the wall against the type paper and drive the expansion sleeve into the hole.
3.At first, put the wall seat core through the wall seat and then fix the wall seat onto the wall with tapping screws;
then put the decorating cover on the wall seat; fix the other wall seat properly by the same method; then insert
the wall seat core head into the fixed rod installation hole. At last,tighten the straight fastening screws
(Attention: ensure that the fastening screw head is inserted into the wall seat core)
;
put the plug cover on properly to finish the product installation.
Attention: Please ensure the wall surface to be flat before installation; be sure to confirm
the distance between the two wall seats. Ensure that the two wall seat cores
coincide with the two installation holes for the fixed rod.

3
1.
2.
3.
4.
7
Note:The above dimensional unit is mm.
TBW02012*
"L Shower" Sliding Rail 600 (Contemporary Type)
Completion wall surface
“TOTO” marking
Installation completion figure
4- 4.2×30
56 56.7

4
mm
900mm
6
Note:The above dimensional unit is mm.
TBW02011*
"L Shower" Sliding Rail 900 (Contemporary Type)
Completion wall surface
“TOTO” marking
nstallation completion figure
4- 4.2×30
56 56.7

5
mm
600mm
5
Note:The above dimensional unit is mm.
TBW01016*
"L Shower" Sliding Rail 600 (Standard Type)
Completion wall surface
“TOTO” marking
Installation completion figure
4- 4.2×30
56 56.7

6
mm
TBW02011*
900mm
4
Note:The above dimensional unit is mm.
Installation completion figure
TBW01015*
"L Shower" Sliding Rail 900 (Standard Type)
Completion wall surface
“TOTO” marking
4- 4.2×30
56 56.7

7
mm
TBW02012*
600mm
3
Use condition
Maintenance
Attentions in construction
Attentions
Use condition, attentions in construction and maintenance
1. The ambient temperature for service is above 0°C.
2. If you want to scrap this product, please do not dispose it as general living garbage. Please let an
independent recovery system dispose, restore and recover in accordance with relevant statutes.
3. The product in the present instructions has the function to place a shower and adjust the bath
height.
To maintain a beautiful appearance of the product, the user is requested to conduct
maintenance and care in the following method.
1. Wipe with a piece of soft cloth frequently and use a piece of soft cloth dipped in water
to wipe from time to time.
2. When dirt exists obviously, please use water to wash sufficiently after wiping with a
neutral detergent.
3. Do not use toilet cleaning powder, abstergent, machine oil, xina water, strong acidic
and alkaline detergent or such detergent as containing particle matters, nylon brush to
clean this product.
Attention: it means that ignoring this mark and misoperation may cause personal
injury or property loss.
1.Do not impact the product. Otherwise, failure, water leakage may occur.
2.Please be sure to install on the concrete wall surface. It is imperative to use the
expansion pipe and tapping screws supplied with the product for installation.
Otherwise, personal injury may occur due to product dropping as a result of instable
installation.
3.After installation, please confirm if the product becomes loose. If so, the product may
fall off or the wall surface damage may result in user falling or being injured.
4.With the product design being updated constantly, the physical object may not
coincide with the figure. However, the basic principle for installation, use is the same.

8
TBW01016*
1
2
Detailed list
Fixed rod assembly.............................................1 set
Wall seat + wall seat core + decorating cover.....2 sets
Plug cover............................................................2 sets
Part package........................................................1 set
Type paper...........................................................1 sheet
Instructions for construction.................................1 copy
Instructions for operation......................................1 copy
The products using this detailed list include:
TBW01015* "L Shower" Sliding Rail 900 (Standard Type)
TBW01016* "L Shower" Sliding Rail 600 (Standard Type)
TBW02011* "L Shower" Sliding Rail 900 (Contemporary Type)
TBW02012* "L Shower" Sliding Rail 600 (Contemporary Type)
Detailed list

715
1915
www.toto.com.cn
1
Contents
Contents
Contents...........................................................1
Detailed list.......................................................2
Use condition, attentions in construction
and maintenance..............................................3
Installation completion figu...............................4-7
Shower holder installation ...............................8
9