Toto YH150RS User manual

Prohibit
Required
Caution about installation
Make sure that the product has no backlash after the installation is complete.
If the product has backlash, it could come off or the wall could collapse, which could result in injury.
Use the wall-mounting screws (pan head tapping screw φ4.5 x 35) that come with the
product for installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Caution about use
Do not climb on the product.
Doing so could damage the product members, which may result in fall and injury.
■If the wall has uneven areas, use washers and spacers to secure a at surface.
■
Secure a space of 130 mm or more from the open side of the paper holder to set paper rolls.
Request about installation
Request
about use
Do not
disassemble
Do not disassemble the items other than those described in this manual.
Doing so could cause the product to be broken.
Use a plywood sheet that is 12 mm or more in thickness on the mounting surface.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
When the mounting surface is a concrete base, use TOTO-designated xing bracket
(optional part).
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
When the mounting surface is a thin wall, mount a reinforcing wooden block that is
30 mm or more in thickness before installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Paper Holder with Spare
YH150RS･YH150LS
MeaningSymbol
The symbol indicates something
that is “Prohibited.”
The symbol on the left indicates “Do not
disassemble.”
The symbol indicates something
that “Must be implemented.”
The symbol on the left indicates
“Required.”
Instruction manual
Please read these “Safety Precautions” carefully before use, and use the product correctly.
Safety Precautions (Be sure to observe these instructions.)
●The following symbols are used to classify and explain
instruction that must be followed.
Cleaning Method
Normal cleaning
Cleaning when the product is very dirty
Precautions for cleaning
2021.4
YP03036N T1
Alkaline
acid
cleaner
Thinner
Cleanser
●After wetting a cloth with water or lukewarm water, wring
it out thoroughly and then use it to wipe the product.
Do not use the following things that can damage the surface
of the product.
●Acid cleaner, alkaline cleaner, and chlorine bleach
●Solvents such as thinner and benzine
●Cleaners containing rough particles such as cleanser and
polishing powder
●Nylon scrubbing brush, other brushes, etc.
●Wipe with a cloth dampened with appropriately-diluted
neutral detergent,and then wipe with a cloth damped with
water. After that, wipe off moisture clean with a dry cloth.
■Request to the contractor
Please install the product correctly in accordance with the
instructions in this instruction manual.
After installation, enter your shop name and the date of
installation in the warranty, and then be sure to hand over this
instruction manual to the customer.
■Request to the customer
Please read this instruction manual carefully and use the
product correctly.
As this instruction manual contains a warranty, please keep it
carefully.
●After reading, keep this instruction manual in a place where users can read it
anytime.
●This instruction manual shows various symbols to correctly and safely use
the product in order to prevent harm to you and other people, and damage
to property. The meanings of those symbols are as follows:
WARNING
CAUTION
When this appears next a topic, this indicates that
ignoring this symbol and mishandling the product could
result in death or serious injury.
When this appears next a topic, this indicates that
ignoring this symbol and mishandling the product could
result in injury or property damage alone.
WARNING
WARNING
CAUTION
In the case of paper rolls with tube, which is φ120 mm or less in outside diameter, use ones of φ38
mm in inside diameter. You can use a paper roll without tube if its inside diameter is 32 to 38 mm.
However, when there is less paper left, it may come off the core rod easily. Paper rolls other than that
described above may not be able to use or may be difcult to use.
★To customer
Please contact the sales shop for replacement parts and warranty.
1

Click!Click!
■ The names of the parts of the paper holder with spare are as follows:
Product Dimensions
■Make sure that you have the following parts:
*Pay attention to the orientation (top and bottom) of the base
plate when mounting it.
Checking the Accessories
Bearing
Replacing with a spare roll
Taking out and cutting paper
■Push up the paper cutting plate
and insert a toilet paper roll into
the core rod.
■In the case of the gure on the right,
when relling a paper roll to the spare
side, follow the procedure shown below.
Names of Parts
How to Use
Relling a paper roll
■Make sure that the product has no backlash after the
installation is complete.
Mounting Method
137
2 3
Core rod
Paper cutting plate
Toilet paper roll
In use
Frame body
Paper
cutting plate
136
30
65
250
300
94
(Flat surface of
the shelf board)
■Take out the paper from the side having the paper cutting plate,
put your hand on the paper cutting plate to hold it and cut the paper.
■Install the paper holder as shown in the gure below.
●Detaching the parts
●Installation
②Make prepared holes and fix the base plate securely using
4 supplied mounting screws.
4 pieces
1 unit
1 unit
2 pieces
Use method label 1 piece
Frame body
Base plate
Surface of the shelf of paper holder
670
700
3065
250
Finished oor surface
*The gure shows YH150RS. For YH150RS
For YH150RS
In the case of YH150RS
In the case of YH150RS
*The gure shows YH150RS.
(Unit: mm)
(Unit: mm)
A piece of advice
①Remove the paper
roll in use.
①Put your hand on the paper
cutting plate to hold it.
②Cut the paper.
②Insert a new
paper roll.
③Insert the removed
paper roll in use again.
①Lift the paper cutting
plate and take out
the tube of the used
toilet roll.
②Move the spare
paper roll in the
arrow direction.
③Lower the paper
cutting plate.
*The figure shows the
view from the back.
Fixing bracket (optional part)
■When you need a xing bracket, please place an order for the
following part No. separately.
Resin plug: 20 piecesT110D28
φ6 × 30
Part No. Shape Details of the set
Preparation for Installation
Mounting Position
■See the gures below for installation.
700
20
700
20
YH150RS YH150LS
130 130
Remove the cushioning material
of the core rod at the end of
installation.
Tip
Tip
Base plate
Pan head tapping screw
(φ4.5 x 35): 4 pieces
Use a screwdriver with a bit
length of 100 mm or longer.
Tip
Frame body
④
⑤
⑥
Base plate
Core rod
cushioning material
Bearing
Core rod
cushioning
material
Frame body
(top plate)
Base plate
Base plate
Bearing
Side plate
Frame body
Notch
Notch
Notch
Frame body
(top plate)
Core rod
cushioning
material
Core rod
Base plate
Notch
Binding head screw
(M4 x 6): 2 pieces
⑦
Core rod
cushioning material
Base-plate-mounting
screw
(pan head tapping screw
4.5 x 35)
Frame-body-xing
screw
(binding head screw
M4 x 6)
When inserting a paper roll into the
core rod, lift the paper roll a little.
You can insert it smoothly by this.
WARNING
■Use a plywood sheet that is 12 mm or more in thickness on
the mounting surface.
■When the mounting surface is a thin wall, mount a
reinforcing wooden block that is 30 mm or more in thickness
before installation.
■When the mounting surface is a concrete base, use
TOTO-designated xing bracket (optional part).
*Secure a space of 130 mm or more from the open side of the
paper holder to set paper rolls.
WARNING
WARNING
WARNING
①Remove the tape that holds the frame body and base plate.
②As shown in the figure, turn the base plate toward you and
remove the bearing from the notch in the frame body.
■Use the base-plate-mounting screws (pan head tapping
screw φ4.5 x 35) that come with the product for
installation.
③Slide the base plate along the notch in the frame body in the
arrow direction.
①Mark hole positions in such a way that the product is placed
horizontally.
③Hold the frame body as shown in the figure so that the top
plate of the frame body faces you, and tilt it in such a way
that the core rod gets in the notch on the back.
④Fit the notch of the frame body on the core rod, and slide the
frame body along the core rod in the arrow direction.
⑤In the state where the side plate of the frame body has
passed over the bearing, tilt the frame body as shown in the
figure and turn it to the front.
⑥Slide the frame body along the bearing toward the wall and
hook the frame body on the base plate.
⑦Lastly, fix the body to the base plate with screws and
remove the core rod cushioning material.
■When the mounting surface is a concrete base, use
TOTO-designated xing bracket (optional part).
Remove the cushioning
material of the core rod at
the end of installation.

Click!Click!
■ The names of the parts of the paper holder with spare are as follows:
Product Dimensions
■Make sure that you have the following parts:
*Pay attention to the orientation (top and bottom) of the base
plate when mounting it.
Checking the Accessories
Bearing
Replacing with a spare roll
Taking out and cutting paper
■Push up the paper cutting plate
and insert a toilet paper roll into
the core rod.
■In the case of the gure on the right,
when relling a paper roll to the spare
side, follow the procedure shown below.
Names of Parts
How to Use
Relling a paper roll
■Make sure that the product has no backlash after the
installation is complete.
Mounting Method
137
2 3
Core rod
Paper cutting plate
Toilet paper roll
In use
Frame body
Paper
cutting plate
136
30
65
250
300
94
(Flat surface of
the shelf board)
■Take out the paper from the side having the paper cutting plate,
put your hand on the paper cutting plate to hold it and cut the paper.
■Install the paper holder as shown in the gure below.
●Detaching the parts
●Installation
②Make prepared holes and fix the base plate securely using
4 supplied mounting screws.
4 pieces
1 unit
1 unit
2 pieces
Use method label 1 piece
Frame body
Base plate
Surface of the shelf of paper holder
670
700
3065
250
Finished oor surface
*The gure shows YH150RS. For YH150RS
For YH150RS
In the case of YH150RS
In the case of YH150RS
*The gure shows YH150RS.
(Unit: mm)
(Unit: mm)
A piece of advice
①Remove the paper
roll in use.
①Put your hand on the paper
cutting plate to hold it.
②Cut the paper.
②Insert a new
paper roll.
③Insert the removed
paper roll in use again.
①Lift the paper cutting
plate and take out
the tube of the used
toilet roll.
②Move the spare
paper roll in the
arrow direction.
③Lower the paper
cutting plate.
*The figure shows the
view from the back.
Fixing bracket (optional part)
■When you need a xing bracket, please place an order for the
following part No. separately.
Resin plug: 20 piecesT110D28
φ6 × 30
Part No. Shape Details of the set
Preparation for Installation
Mounting Position
■See the gures below for installation.
700
20
700
20
YH150RS YH150LS
130 130
Remove the cushioning material
of the core rod at the end of
installation.
Tip
Tip
Base plate
Pan head tapping screw
(φ4.5 x 35): 4 pieces
Use a screwdriver with a bit
length of 100 mm or longer.
Tip
Frame body
④
⑤
⑥
Base plate
Core rod
cushioning material
Bearing
Core rod
cushioning
material
Frame body
(top plate)
Base plate
Base plate
Bearing
Side plate
Frame body
Notch
Notch
Notch
Frame body
(top plate)
Core rod
cushioning
material
Core rod
Base plate
Notch
Binding head screw
(M4 x 6): 2 pieces
⑦
Core rod
cushioning material
Base-plate-mounting
screw
(pan head tapping screw
4.5 x 35)
Frame-body-xing
screw
(binding head screw
M4 x 6)
When inserting a paper roll into the
core rod, lift the paper roll a little.
You can insert it smoothly by this.
WARNING
■Use a plywood sheet that is 12 mm or more in thickness on
the mounting surface.
■When the mounting surface is a thin wall, mount a
reinforcing wooden block that is 30 mm or more in thickness
before installation.
■When the mounting surface is a concrete base, use
TOTO-designated xing bracket (optional part).
*Secure a space of 130 mm or more from the open side of the
paper holder to set paper rolls.
WARNING
WARNING
WARNING
①Remove the tape that holds the frame body and base plate.
②As shown in the figure, turn the base plate toward you and
remove the bearing from the notch in the frame body.
■Use the base-plate-mounting screws (pan head tapping
screw φ4.5 x 35) that come with the product for
installation.
③Slide the base plate along the notch in the frame body in the
arrow direction.
①Mark hole positions in such a way that the product is placed
horizontally.
③Hold the frame body as shown in the figure so that the top
plate of the frame body faces you, and tilt it in such a way
that the core rod gets in the notch on the back.
④Fit the notch of the frame body on the core rod, and slide the
frame body along the core rod in the arrow direction.
⑤In the state where the side plate of the frame body has
passed over the bearing, tilt the frame body as shown in the
figure and turn it to the front.
⑥Slide the frame body along the bearing toward the wall and
hook the frame body on the base plate.
⑦Lastly, fix the body to the base plate with screws and
remove the core rod cushioning material.
■When the mounting surface is a concrete base, use
TOTO-designated xing bracket (optional part).
Remove the cushioning
material of the core rod at
the end of installation.

Prohibit
Required
Caution about installation
Make sure that the product has no backlash after the installation is complete.
If the product has backlash, it could come off or the wall could collapse, which could result in injury.
Use the wall-mounting screws (pan head tapping screw φ4.5 x 35) that come with the
product for installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Caution about use
Do not climb on the product.
Doing so could damage the product members, which may result in fall and injury.
■If the wall has uneven areas, use washers and spacers to secure a at surface.
■
Secure a space of 130 mm or more from the open side of the paper holder to set paper rolls.
Request about installation
Request
about use
Do not
disassemble
Do not disassemble the items other than those described in this manual.
Doing so could cause the product to be broken.
Use a plywood sheet that is 12 mm or more in thickness on the mounting surface.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
When the mounting surface is a concrete base, use TOTO-designated xing bracket
(optional part).
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
When the mounting surface is a thin wall, mount a reinforcing wooden block that is
30 mm or more in thickness before installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Paper Holder with Spare
YH150RS･YH150LS
MeaningSymbol
The symbol indicates something
that is “Prohibited.”
The symbol on the left indicates “Do not
disassemble.”
The symbol indicates something
that “Must be implemented.”
The symbol on the left indicates
“Required.”
Instruction manual
Please read these “Safety Precautions” carefully before use, and use the product correctly.
Safety Precautions (Be sure to observe these instructions.)
●The following symbols are used to classify and explain
instruction that must be followed.
Cleaning Method
Normal cleaning
Cleaning when the product is very dirty
Precautions for cleaning
2021.4
YP03036N T1
Alkaline
acid
cleaner
Thinner
Cleanser
●After wetting a cloth with water or lukewarm water, wring
it out thoroughly and then use it to wipe the product.
Do not use the following things that can damage the surface
of the product.
●Acid cleaner, alkaline cleaner, and chlorine bleach
●Solvents such as thinner and benzine
●Cleaners containing rough particles such as cleanser and
polishing powder
●Nylon scrubbing brush, other brushes, etc.
●Wipe with a cloth dampened with appropriately-diluted
neutral detergent,and then wipe with a cloth damped with
water. After that, wipe off moisture clean with a dry cloth.
■Request to the contractor
Please install the product correctly in accordance with the
instructions in this instruction manual.
After installation, enter your shop name and the date of
installation in the warranty, and then be sure to hand over this
instruction manual to the customer.
■Request to the customer
Please read this instruction manual carefully and use the
product correctly.
As this instruction manual contains a warranty, please keep it
carefully.
●After reading, keep this instruction manual in a place where users can read it
anytime.
●This instruction manual shows various symbols to correctly and safely use
the product in order to prevent harm to you and other people, and damage
to property. The meanings of those symbols are as follows:
WARNING
CAUTION
When this appears next a topic, this indicates that
ignoring this symbol and mishandling the product could
result in death or serious injury.
When this appears next a topic, this indicates that
ignoring this symbol and mishandling the product could
result in injury or property damage alone.
WARNING
WARNING
CAUTION
In the case of paper rolls with tube, which is φ120 mm or less in outside diameter, use ones of φ38
mm in inside diameter. You can use a paper roll without tube if its inside diameter is 32 to 38 mm.
However, when there is less paper left, it may come off the core rod easily. Paper rolls other than that
described above may not be able to use or may be difcult to use.
★To customer
Please contact the sales shop for replacement parts and warranty.
1