Toto YC990 Installation instructions

ENGLISH ESPAÑOL FRANÇAIS
Installation and Owner’s Manual
Manual de Instrucciones y del Propietario
Manuel d’Installation et d’Utilisation
YB990 Bath towel holder/toallero para toalla de Baño/
Support pour Serviette de Bain
YC990 hand towel holder/ toallero para toalla de ManoS/
Support pour Serviette àMain
Yh990 roBe hook/perCha para Bata/CroChet àpeignoir
Yp990 paper holder/portarolloS/porte-papier hYgiénique
YH990 YP990
YC990
YB990

2
ENGLISH
CAUTION!
Always wear appropriate eye protection while operating drill
Do not force accessories into alignment. Instead, loosen screws and
readjust
Minimum wall thickness: 1/2” (12mm)
If the installation surface is too thin, reenforce by using a piece of
wood over 1-1/4” (30mm) thick before installation
When mounting on concrete walls, use provided anchors or equivalent
Do not lean on or press on any part of the product
Do not use products to hold objects heavier than a towel
•
•
•
•
•
•
•
THANKS FOR CHOOSING TOTO®!
The mission of TOTO®is to provide the world with healthy, hygienic
and more comfortable lifestyles. We design every product with the
balance of form and function as a guiding principle. Congratulations on
your choice.
CARE AND CLEANING
Your new accessory is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with mild soap, rinse
thoroughly with warm water and dry with a clean, soft cloth. Do not
use abrasive cleaners, steel wool or harsh chemicals, as these will dull
the nish. Failure to follow these instructions may void your warranty.
TABLE OF CONTENTS
Thanks for Choosing Toto®! ........................................................................................... 2
Care And Cleaning.......................................................................................................... 2
Caution............................................................................................................................ 2
Before Installation........................................................................................................... 3
Positioning The Product..................................................................................................3
Installation Procedure ..................................................................................................... 4
Product Specication ...................................................................................................... 6
Replacement Parts........................................................................................................... 7
Warranty.......................................................................................................................... 8

3
ENGLISH
BEFORE INSTALLATION
Check to make sure you have the following parts shown below•
Attached Components YB990 YC990 YH990 YP990
Pan Head Wall Screw
(Pan head tapping screw φ4.5 x 40) ── ── 2──
Flat Head Wall Screw
(Flat head tapping screw φ5 x 40) 4 3 ── 4
Wall Anchor 4 3 2 4
Mount ── ── 1──
Body Screw
(Flat head phillips screw M4x8) ── ── 2──
Cover 1 1 ── 1
Cover Screw
(Flat head Hex screw M3 x 20) 3 2 ── 2
Hex wrench (2mm) 1 1 ── 1
POSITIONING THE PRODUCT
The following gures are suggestions only. Please determine the
position based on individual requirements
Please check that there is over 130mm space on the left of the paper
holder to install the paper.
•
•
Floor surface
Wall surface
Wall surface
4ft (1200mm)*
26” (650mm)*
5-1/2ft (1700mm)*
<YH990>
<YB990 • YC990>
4”(100mm)
<YP990>
*Suggested dimension

4
ENGLISH
INSTALLATION PROCEDURES
YB990 Bath Towel Holder
•
YC990 Hand Towel Holder
Hold the body against the wall
and mark drill points. Open 1/4”
(6mm) in diameter., over 1-1/2”
(40mm) deep holes for the wall
anchor
Drill wall holes for the provided
wall anchors. Hold the front long
driver to mount the body on the
wall with at head wall screws to
x the body. Avoid scarring the
body with tools
Install the cover from below the
body. Secure cover with provided
hex wrench and cover screws.
1.
2.
3.
〈YC990〉
〈YB990〉
Cover screw
Cover
Wall screw position
<Front>
Flat Head Wall screw
Wall hole
Wall anchor
6″
(150mm)
6″
(150mm)
6″
(150mm)
6″
(150mm)
6″
(150mm)

5
ENGLISH
YH990 Robe Hook
Place the mount against the wall
and mark drill points. Open 1/4”
(6mm) in diameter., over 1-1/2”
(40mm) deep holes for the wall
anchor
Drill the holes for the provided
wall anchors. Use pan head wall
screws to attach the mount. Make
sure mount is securely mounted
Push the body onto the mount, use
body screws to secure the body
1.
2.
3.
YP990 Paper Holder
Hold the body against the wall
and mark drill points. Open 1/4”
(6mm) in diameter., over 1-1/2”
(40mm) deep holes for the wall
anchor
Drill wall holes for the provided
wall anchors. Hold the front long
driver to mount the body on the
wall with at head wall screws to
x the body. Avoid scarring the
body with tools
Install the cover from below the
body. Secure cover with provided
hex wrench and cover screws.
1.
2.
3.
Wall hole
Body screw
Body
Wall screw position
3/4″
(20mm)
Mount
Wall Anchor
Pan Head Wall screw
Cover screw
Cover
Wall screw position
<Front>
Flat Head Wall Screws
Wall hole
Wall Anchor
Body
4″
(100mm)
2″
(50mm)
2″
(50mm)