Toto Soap dispenser User manual

TOTO SOAP DISPENSER
Automatic Soap Dispenser
03669 T1 2009.04
Owner’s Manual
Safety Warnings .......................... 1
User Warnings ............................. 3
Names and Numbers of Parts ..... 4
Before Using Your New Product . 5
NOTE TO INSTALLER : PLEASE GIVE THIS MANUAL TO THE
CUSTOMER AFTER INSTALLATION.
How to Use this Product ............... 6
Filling the Product
with Liquid Soap .......................... 7
Making Adjustments ..................... 8
Day-to-Day Care ........................... 9
Recommended
Periodic Inspections .................. 10
Troubleshooting ......................... 13
Specifications ............................ 14
WARRANTY
■Thank you for your recent purchase of the
TOTO product. Please read the enclosed
information to ensure the safe use of your
product.
■Please keep this owner’s manual in a safe
place.
■Warranty Registration and Inquiry
For product warranty registration, TOTO
U.S.A. Inc. recommends online Warranty
Registration. Please visit our web site
http://www.totousa.com. If you have questions
regarding warranty policy or coverage, please
contact TOTO U.S.A. Inc., Customer Service
Department, 1155 Southern Road, Morrow,
GA 30260 [phone] or [phone]
when calling from outside of U.S.A.

Please read these Safety Warnings carefully in order to use your new product properly.
Symbol
Warning
Meaning
Forbidden
Do Not Use
In Wet Areas
This symbol is used to indicate that it is possible that misuse of the product after ignor-
ing the warning associated this symbol could result in someoneÕs injury or death.
This symbol is used to indicate that it is possible that misuse of the product after ignor-
ing the warning associated this symbol could result in damage or physical loss.
After reading the manual, please store it in a place there it can be referred to whenever necessary.
This ownerÕs manual uses symbols regarding the proper and safe use of this device and can help to
prevent harm to yourself or others or damage to assets before they can occur.
Those symbols are shown below.
We have categorized and explained the various activities in the table below.
Indicates something ÒforbiddenÓ
that should not be done.
Please do not disassemble.
Please do not touch places
marked with this symbol.
Indicates that the product should not
be used in the bath, shower or other
wet area.
Please remove the power supply
cord from the outlet.
Indicates a ÒrequiredÓ activity.
Please be sure to comply.
Depending upon the parts number, the actual item may differ somewhat from the diagram.
Warning
Caution
Please do not handle the cord roughly or use an outlet that is
not properly tightened.
Doing so could cause a fire.
Please refrain from pouring water over the power supply plug
or the functioning modules.
It is an electrical product; doing so could cause a fire or electric shock.
Please refrain from connecting the product with a direct cur-
rent power supply or a power supply with a different voltage.
Doing so could cause an electric shock.
Please do not install in a bathing area or humid place.
Doing so could cause product failure or electric shock.
Safety Warnings
1
Getting Started
(For your safety, please be sure
to follow these guidelines.)

2
Getting Started
Please do not install the product outside.
Doing so could cause product failure.
Please remove any dust found on the power supply plug.
If dust builds up on the power supply plug, then moisture could cause the
insulation to fail and cause a fire. Please wipe the power supply plug with a
dry cloth.
When plugging the power supply plug into the outlet, please
insert the plug fully into place. TOTO recommends that the AC
adapter be connected to a GFCI-protected outlet.
Not doing so could cause a fire.
Please do not, under any circumstances, touch any
internal parts other than the potentiometer knob.
Doing so could cause product failure or electric shock.
Please refrain from touching the power supply plug
during thunderstorms or lightning.
Doing so could result in an electric shock.
Please do not touch the power supply plug with wet
hands.
Doing so could cause product failure or electric shock.
Under no circumstances should anyone other than a factory
repair technician disassemble, repair or modify any items
other than those designated for maintenance or inspection.
Doing so could cause product failure or electric shock.
Please refrain from striking or using excessive force
on the product.
Doing so could cause product failure or leaking.
Please refrain from using disinfectant.
Please refrain from using cresol or similar disinfectant
in place of liquid soap.
Doing so could cause damage to the product or interfere with soap dispensing.

User Warnings
(Please observe the following guidelines.)
Unplug Product
Caution
Forbidden
Be Sure to
Do This
Please refrain from using liquid soap if rashes, dermatitis or
other skin problems become apparent.
Not doing so could make symptoms worse.
Please check regularly, the area around the pipes (inside the
cabinet, including inside the inspection port) to make sure
that there are no leaks.
Not doing so could leave a liquid soap leak, caused by undetected deteriora-
tion or wear. A leak could cause damage to personal property.
Please do not use this product in a place where the liquid
soap in the tank or the water in the pipes can freeze.
The devices could rupture, which might leak and damage personal property.
When the product will go unused for long periods of time,
please unplug the power supply.
Not doing so could cause an unforeseen accident due to malfunctioning or
product failure.
Please keep obstacles from getting into the sensor area.
Otherwise the product could malfunction.
Please do not peer inside the nozzle.
Doing so could cause soap to get in oneÕs eyes or other injury. In the unlike-
ly event that soap does get in someoneÕs eyes, (remove contact lenses, if
applicable) and then rinse the eyes with large amounts of water for at least
15 minutes before immediately seeking the advice of a physician.
Please use a clean container when filling the product.
The use of paint thinner or other organic solvents or detergents could
damage the product or cause other problems.
Liquid Soap.
For proper system operation, please use only TOTO approved soap.
3
Getting Started

Item
<Standard>
Base Unit
Number of Dispenser
Tube and Cord Length
TES1ADC-05
12
16.4' (5m)
3
TES2ADC-05 TES3ADC-05
Item
<Special Order Item>
Base Unit
Number of Dispenser
Tube and Cord
Length
TES3ADC-12 TES4ADC-12 TES5ADC-12 TES6ADC-12
3456
39.4' (12m)
(Model TES6ADC-12 shown)
Internal
Sensor
Lamp
Sensor
Air Pump
Cords
Soap Intake
Tank Connecting Hose
AC Adapter
Liquid Soap
Spout
Tube (Air)
Tube
(Liquid Soap)
Dispenser
Sub-Tank (Special Order Item)
Soap Intake
for standard tank
Air venting
hose
Controller (Inside Case)
Liquid Soap Tank
Sensor Module
4
Names and Numbers of Parts
Getting Started

Internal
Sensor
Lamp
AC Adapter
Sensor
Sensor portion
Checking the Power Supply
Check the Connections of the Tubes and Hoses
Checking the Connections of the Connectors
Click
Lock
Clamp
Coupling cap
Soap tube
(white)
Air Tube
Liquid Soap Tube
Is the Power On?
Please push the power supply plug completely into the
outlet.
Are the tubes and hoses con-
nected?
Please check to see that the pump module, the liquid
soap tube connectors and the air tube connectors are
securely connected. When tanks or sub-tanks are con-
nected, please check to see that the connecting hoses
are secure.
* Please check to see that there are no sharp kinks in
the tubes or hoses.
Are the connectors properly
connected?
Please check to see that sensor connectors (white) and
the air-pump connectors (green) are securely connec-
ted.
Caution
For approximately 10 minutes after turning on the pow-
er, the internal sensor lamp will blink every time is sen-
ses something. This is not a malfunction.
(The lamp will stop blinking after approximately 10 min-
utes.)
Before Using Your New Product
5
Getting Started

Dispensing Liquid Soap
Dispenser Spout
Place Hands Near Dispenser
Spout.
When the sensor senses someoneÕs hands, it dispen-
ses a mousse-like liquid soap.
The dispensing time is approximately 0.2 second.
Dispensing stops when the hand is taken away from
the dispenser.
If oneÕs hands remain in front of the dispenser, the
mousse-like liquid soap will again be dispensed after
approximately a 2-second delay. This process can be
repeated up to three times.
In order to prevent mischief, the liquid soap dispenser
will stop after 3 times, but repeated soap dispensing is
possible by moving the hands away and placing them
in front of the dispenser again.
The soap might go flying off in an unexpected
direction.
Caution
Please do not obstruct the dispenser
spout opening.
When the tip becomes soiled, please wipe
away the debris using a damp cloth.
Please do not put foam on the tip of
the dispenser. If the sensor becomes
soiled, it could malfunction.
6
How to Use this Product
How to Use

Filling the Sub-Tank (Only if a sub-tank has been installed.)
Filter
Open
Close
Sensor
Filter
Internal Sensor
Lamp
Remove the cap on the liquid
soap tank.
1.
Slowly pour the liquid soap
into the holding tank.
2.
Please keep an eye on the level as you pour the liq-
uid soap in slowly so that it doesnÕt become foamy.
Please pour the liquid soap through the built-in filter.
Firmly replace the cap on the
liquid soap tank.
3.
Please make sure that the cap is securely in place
after filling the tank.
When a sub-tank has been instal-
led, please fill the liquid soap from
the opening in the sub-tank.
NOTE: Pour soap slowly to avoid bubbles in the tank.
Please refill the liquid soap when the internal sensor lamp (red) starts blinking.
If the soap is very slow to drain into the tank of exces-
sive bubbling occurs, please clean the filter and cap
area. (see page 11)
Filling the Product with Liquid Soap
7
How to Use

Warning
Caution
Adjusting the Liquid Soap Dispensing Time
Guide to the Positions of the Potentiometer Knob
0.2 Seconds 1.4 Seconds 2.0 Seconds
Controller Cover
Potentiometer
Knob
Shorter Longer
Do Not Touch
Please do not, under any circumstances, touch to any inter-
nal parts other than the potentiometer knob.
Doing so could cause product failure or electric shock.
Unplug Product
When the product will go unused for long periods of time,
please unplug the power supply.
Not doing so could cause an unforeseen accident due to malfunctioning or
product failure.
Remove power supply plug.1.
Using a Phillips head screwdriv-
er, remove the four screws and
the controller cover on the side
of the tank.
2.
Turn the potentiometer knob to
adjust the dispensing time.
3.
The dispensing time of the liquid soap can be ad-
justed as necessary from 0.2 seconds to 20 sec-
onds.
* The factory setting is approximately 0.2 second.
Please turn the potentiometer knob at the lower left
of the base plate and adjust the maximum dispens-
ing time per use.
Replace the Controller Cover. 4.
* Please be careful not to pinch the cords with the lid.
* Please tighten screws fully.
* The liquid soap dispensing time can be adjusted as follows.
0.2 ~ 2.0 Seconds (in 0.2-second increments)
2.5, 3.0, 5.0, 10.0 or 20.0 seconds
8
Making Adjustments
How to Use

Care with a Cloth
In order to enjoy your new product, please follow the guidelines below
on a day-to-day basis.
For Light Cleaning
Caution
Sensor Surface
Dispenser Spout
Please wring out a cloth that has been soaked in water and
wipe away any debris adhering to the dispenser or sensor.
When cleaning around the sen-
sor, please be careful not to
scratch the surface of the sensor.
For Heavy-Duty Cleaning
Please avoid using cleansers that
might scratch the surface of dis-
penser.
These include:
Detergents containing acid, chlorine
bleach or alkali.
Solvents like paint thinner or benzene.
Detergents with coarse granules, polishing
powder or cleanser. Nylon scrubbers, pot
scrubbers, brushes, etc.
After wiping away debris with a cloth containing a suitable
amount of a neutral, dishwashing detergent, wipe clean with
a damp cloth.
Day-to-Day Care
9
Maintenance