Toto YH700AD Installation instructions

If the wall has uneven areas, use washers and spacers to secure a at surface.
Request about installation
Double Paper Holder with Shelf/
Double Paper Holder
Instruction manual
YH700AD･YH700AW
Prohibit
Prohibit
Required
Caution about installation
Use a plywood sheet that is 12 mm or more in thickness on the mounting surface.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Do not install the product in places where water may be splashed over the product or in
humid places, including outdoor and in a bathroom.
Do not wet the base and the product.
Doing so could cause the product to drop due to corrosion of the members, and may result in injury or
serious accident.
Use the supplied wall-mounting screws for installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
When the mounting surface is a tile or concrete wall, use a commercially available plugs
for concrete, etc.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Make sure that the product has no backlash after the installation is complete.
If the product has backlash, it could come off or the wall could collapse, which could result in user’s fall and injury.
When the mounting surface is a thin wall, mount a reinforcing wooden block that is 30
mm or more in thickness before installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Warning and caution about use
Do not hang from or lean on the parts of the product.
Doing so could cause the installed product to be unstable and drop, and may result in injury.
Do not put a heavy object other than toilet paper rolls on the core rod.
Doing so could cause the installed product to be unstable and drop, and may result in injury.
Do not give water or extreme moisture to the product.
The product could drop due to the warpage or corrosion of the members, which could lead to injury or
serious accident.
Please read these “Safety Precautions” carefully before use, and use the product correctly.
Safety Precautions (Be sure to observe these instructions.)
MeaningSymbol The symbol indicates something
that is “Prohibited.”
The symbol on the left indicates “Do
not disassemble.”
The symbol indicates something
that is “Prohibited.”
The symbol on the left indicates “Do
not disassemble.”
Required
If the product has backlash during use, stop using it immediately and contact the
installation service shop, sales shop to receive inspection.
Failure to do so could cause the product to drop and a user to fall, which could lead to injury or serious
accident.
Do not disassemble the product.
Doing so could cause the product to be broken.
Do not
disassemble
■Request to the contractor
Please install the product correctly in accordance with the
instructions in this instruction manual.
After installation, enter your shop name and the date of
installation in the warranty, and then be sure to hand over this
instruction manual to the customer.
■Request to the customer
Please read this instruction manual carefully and use the
product correctly.
As this instruction manual contains a warranty, please keep it
carefully.
●After reading, keep this instruction manual in a place where users can read it
anytime.
●This instruction manual shows various symbols to correctly and safely use
the product in order to prevent harm to you and other people, and damage
to property. The meanings of those symbols are as follows:
●The following symbols are used to classify and explain
instruction that must be followed.
WARNING
CAUTION
CAUTION
CAUTION
WARNING
When this appears next a topic, this indicates that
ignoring this symbol and mishandling the product
could result in death or serious injury.
When this appears next a topic, this indicates that
ignoring this symbol and mishandling the product
could result in injury or property damage.
2021.4
YP03093 T1
★To customer
Please contact the sales shop for replacement parts and warranty.
1

●Wipe with a cloth dampened with appropriately-diluted neutral detergent, and then wipe with
a cloth dampened with water. After that, wipe off moisture clean with a dry cloth.
Wall-mounting screw positions
90 to 110 90 to 110
26
700
25 25
700
250
45°
25
①
②
555
㈰㈪
45°
Names of Parts
Checking the Accessories
Product Dimensions
Mounting Position
Mounting Method
■Make sure that you have the following parts:
■How to set paper rolls
①While lifting the paper cutting plate,
②insert paper rolls from the side.
Paper cutting plate
Shelf board
Core rod
Paper cutting plate
Core rod
Normal cleaning
●After wetting a cloth with water or lukewarm water, wring it out thoroughly and then use it to wipe the product.
Cleaning when the product is very dirty
Precautions for cleaning
Do not use the following things that can damage the surface of the product.
●Acid cleaner, alkaline cleaner, and chlorine bleach
●Solvents such as thinner and benzine
●Cleaners containing rough particles such as cleanser and polishing powder
●Nylon scrubbing brush, other brushes, etc.
Cleaning
How to Use
Accessory parts
Wall-mounting screw (pan head
tapping screw φ4.5 x 30) 4 pieces
Wall-mounting screw
(pan head tapping screw φ4.5 x 40): 4 pieces
Wall-mounting screw
(pan head tapping screw φ4.5 x 30): 4 pieces
The gures below are reference examples of installation. Please determine a mounting position according to the situation of the installation site.
Request about use
Preparation for Installation
■When the mounting surface is a tile or concrete wall, use a commercially available plugs for concrete, etc.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
■
When the mounting surface is a thin wall, mount a reinforcing wooden block that is 30 mm or more in thickness before installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
■Use a plywood sheet that is 12 mm or more in thickness on the mounting surface.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
*Depending on paper quality and the way of cutting, paper may difcult
to cut off.
①
②
■How to cut paper
<One-hand cutting function>
①Pull out the paper diagonally
downward.
②Place the blade of the paper
cutting plate on the edge of the paper and
cut the paper along the paper cutting plate
at an angle of about 45°.
Double paper
holder
Wall-mounting screw (pan head
tapping screw φ4.5 x 40) 4 pieces
Double paper
holder with shelf
・Use paper rolls which are φ120 mm or less in diameter, 114 mm or less in width, and φ38 mm in inside
diameter of tube.
・Paper rolls that do not meet the above condition may not be able to use or may be difcult to use.
・If the product body becomes loose, use a Phillips screwdriver to retighten the screws that fasten the
product body.
CAUTION
①Mark hole positions in such a way that the product
is placed horizontally.
②Make prepared holes and x the product using 4
supplied wall-mounting screws (pan head tapping
screw).
CAUTION
■Use the supplied wall-mounting screws for
installation.
Failure to do so could cause the installed
product to be unstable and drop, and may
result in injury.
■Make sure that the product has no backlash
after the installation is complete.
If the product has backlash, it could come off
or the wall could collapse, which could result in
user’s fall and injury.
3
2
Wall-mounting surface
Wall-mounting surface
Wall-mounting surface
Wall-mounting surface
Double paper holder with shelf Double paper holder
Double paper holder
with shelf
YH700AD
Double paper holder
with shelf
YH700AD
Double paper holder
YH700AW
Double paper holder
YH700AW
Double paper holder with shelf YH700AD
Double paper holder YH700AW
300
220
20 20
300
20 20
120
102.5
26
37
88
Finished oor surface
71.5
22
20.522
220
25
25
26
YH700AD YH700AW
■Flat counter
For versatile toilet
package
Finished oor surface Finished oor surface
Cleanser
Alkaline
acid
cleaner
Thinner

●Wipe with a cloth dampened with appropriately-diluted neutral detergent, and then wipe with
a cloth dampened with water. After that, wipe off moisture clean with a dry cloth.
Wall-mounting screw positions
90 to 110 90 to 110
26
700
25 25
700
250
45°
25
①
②
555
㈰㈪
45°
Names of Parts
Checking the Accessories
Product Dimensions
Mounting Position
Mounting Method
■Make sure that you have the following parts:
■How to set paper rolls
①While lifting the paper cutting plate,
②insert paper rolls from the side.
Paper cutting plate
Shelf board
Core rod
Paper cutting plate
Core rod
Normal cleaning
●After wetting a cloth with water or lukewarm water, wring it out thoroughly and then use it to wipe the product.
Cleaning when the product is very dirty
Precautions for cleaning
Do not use the following things that can damage the surface of the product.
●Acid cleaner, alkaline cleaner, and chlorine bleach
●Solvents such as thinner and benzine
●Cleaners containing rough particles such as cleanser and polishing powder
●Nylon scrubbing brush, other brushes, etc.
Cleaning
How to Use
Accessory parts
Wall-mounting screw (pan head
tapping screw φ4.5 x 30) 4 pieces
Wall-mounting screw
(pan head tapping screw φ4.5 x 40): 4 pieces
Wall-mounting screw
(pan head tapping screw φ4.5 x 30): 4 pieces
The gures below are reference examples of installation. Please determine a mounting position according to the situation of the installation site.
Request about use
Preparation for Installation
■When the mounting surface is a tile or concrete wall, use a commercially available plugs for concrete, etc.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
■
When the mounting surface is a thin wall, mount a reinforcing wooden block that is 30 mm or more in thickness before installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
■Use a plywood sheet that is 12 mm or more in thickness on the mounting surface.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
*Depending on paper quality and the way of cutting, paper may difcult
to cut off.
①
②
■How to cut paper
<One-hand cutting function>
①Pull out the paper diagonally
downward.
②Place the blade of the paper
cutting plate on the edge of the paper and
cut the paper along the paper cutting plate
at an angle of about 45°.
Double paper
holder
Wall-mounting screw (pan head
tapping screw φ4.5 x 40) 4 pieces
Double paper
holder with shelf
・Use paper rolls which are φ120 mm or less in diameter, 114 mm or less in width, and φ38 mm in inside
diameter of tube.
・Paper rolls that do not meet the above condition may not be able to use or may be difcult to use.
・If the product body becomes loose, use a Phillips screwdriver to retighten the screws that fasten the
product body.
CAUTION
①Mark hole positions in such a way that the product
is placed horizontally.
②Make prepared holes and x the product using 4
supplied wall-mounting screws (pan head tapping
screw).
CAUTION
■Use the supplied wall-mounting screws for
installation.
Failure to do so could cause the installed
product to be unstable and drop, and may
result in injury.
■Make sure that the product has no backlash
after the installation is complete.
If the product has backlash, it could come off
or the wall could collapse, which could result in
user’s fall and injury.
3
2
Wall-mounting surface
Wall-mounting surface
Wall-mounting surface
Wall-mounting surface
Double paper holder with shelf Double paper holder
Double paper holder
with shelf
YH700AD
Double paper holder
with shelf
YH700AD
Double paper holder
YH700AW
Double paper holder
YH700AW
Double paper holder with shelf YH700AD
Double paper holder YH700AW
300
220
20 20
300
20 20
120
102.5
26
37
88
Finished oor surface
71.5
22
20.522
220
25
25
26
YH700AD YH700AW
■Flat counter
For versatile toilet
package
Finished oor surface Finished oor surface
Cleanser
Alkaline
acid
cleaner
Thinner

If the wall has uneven areas, use washers and spacers to secure a at surface.
Request about installation
Double Paper Holder with Shelf/
Double Paper Holder
Instruction manual
YH700AD･YH700AW
Prohibit
Prohibit
Required
Caution about installation
Use a plywood sheet that is 12 mm or more in thickness on the mounting surface.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Do not install the product in places where water may be splashed over the product or in
humid places, including outdoor and in a bathroom.
Do not wet the base and the product.
Doing so could cause the product to drop due to corrosion of the members, and may result in injury or
serious accident.
Use the supplied wall-mounting screws for installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
When the mounting surface is a tile or concrete wall, use a commercially available plugs
for concrete, etc.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Make sure that the product has no backlash after the installation is complete.
If the product has backlash, it could come off or the wall could collapse, which could result in user’s fall and injury.
When the mounting surface is a thin wall, mount a reinforcing wooden block that is 30
mm or more in thickness before installation.
Failure to do so could cause the installed product to be unstable and drop, and may result in injury.
Warning and caution about use
Do not hang from or lean on the parts of the product.
Doing so could cause the installed product to be unstable and drop, and may result in injury.
Do not put a heavy object other than toilet paper rolls on the core rod.
Doing so could cause the installed product to be unstable and drop, and may result in injury.
Do not give water or extreme moisture to the product.
The product could drop due to the warpage or corrosion of the members, which could lead to injury or
serious accident.
Please read these “Safety Precautions” carefully before use, and use the product correctly.
Safety Precautions (Be sure to observe these instructions.)
MeaningSymbol The symbol indicates something
that is “Prohibited.”
The symbol on the left indicates “Do
not disassemble.”
The symbol indicates something
that is “Prohibited.”
The symbol on the left indicates “Do
not disassemble.”
Required
If the product has backlash during use, stop using it immediately and contact the
installation service shop, sales shop to receive inspection.
Failure to do so could cause the product to drop and a user to fall, which could lead to injury or serious
accident.
Do not disassemble the product.
Doing so could cause the product to be broken.
Do not
disassemble
■Request to the contractor
Please install the product correctly in accordance with the
instructions in this instruction manual.
After installation, enter your shop name and the date of
installation in the warranty, and then be sure to hand over this
instruction manual to the customer.
■Request to the customer
Please read this instruction manual carefully and use the
product correctly.
As this instruction manual contains a warranty, please keep it
carefully.
●After reading, keep this instruction manual in a place where users can read it
anytime.
●This instruction manual shows various symbols to correctly and safely use
the product in order to prevent harm to you and other people, and damage
to property. The meanings of those symbols are as follows:
●The following symbols are used to classify and explain
instruction that must be followed.
WARNING
CAUTION
CAUTION
CAUTION
WARNING
When this appears next a topic, this indicates that
ignoring this symbol and mishandling the product
could result in death or serious injury.
When this appears next a topic, this indicates that
ignoring this symbol and mishandling the product
could result in injury or property damage.
2021.4
YP03093 T1
★To customer
Please contact the sales shop for replacement parts and warranty.
1