Town & Country Fireplaces D2 Series Installation and operation manual

100001172-50 TCWS54D2 021118-12
Dimensions | Clearances | Venting
IMPORTANT
This booklet is intended as a basic specification
guide for architects, designers and builders.
Please refer to the Instruction Manual supplied
with the fireplace for detailed information regarding
installation and operation.
Product installation manuals can also be viewed at:
www.townandcountryfireplaces.com
FOR ARCHITECTS & DESIGNERS
TCWS54
SERIES D2

2
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12 100001172-50 TCWS54D2
Fireplace Dimensions
Examples of Common Locations
TCWS54.D2 Cad Drawing
Available at
www.townandcountryreplaces.com

3
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12
100001172-50 TCWS54D2
Mantel Clearance Chart
Minimum Clearances to Combustibles
* MANTEL CLEARANCE
A 9”
B 6”
C 3”
MANTEL CLEARANCE
CHART
** MANTEL DEPTH
D 12”
E 6 3/4”
F 1 1/2”
A
B
C
D
E
F
29 3/4"
24"
4“
CEILING
ADJACENT WALL
OR MANTEL SUPPORT
12”
COMBUSTIBLE FLOOR
COMBUSTIBLE HEARTH
*
**
MANTEL
Unit may be recessed up to 4 1/2” with
non-combustible masonary type material
Minimum Clearances:
Side standoffs .................................................. 0 in. (0 mm)
Back standoffs ................................................. 0 in. (0 mm)
Top standoffs.................................................... 0 in. (0 mm)
Bottom of appliance ......................................... 0 in. (0 mm)
Adjacent side wall............................................. 4 in. (102 mm)
Ceiling to appliance .......................................... 24 in. (610 mm)
*Mantel to appliance.......................................... See mantle clearance
.................................................................... chart above
**Maximum Mantel extension............................. See mantle clearance
..................................................................... chart above
Mantel support ................................................. 4 in. (102 mm)
Vertical vent pipe ............................................. 1 3/4" in.(45 mm)
Horizontal Vent pipe (Top, sides and bottom) .... 1 3/4" in.(45 mm)
MAY USE COMBUSTIBLE
FACING MATERIAL IN THIS
AREA
NON-COMBUSTBLE
FINISH MATERIAL
NON-COMBUSTIBLE ZONE.
DO NOT INSTALL ANY COMBUSTIBLE
MATERIAL, ELECTRICAL WIRING OR GAS
PLUMBING IN THIS AREA.
COMBUSTIBLE FRAMING AND
FINISH WALL ABOVE STANDOFFS
STANDOFF
STEEL FRAMING
FIREPLACE
FRONT
TOP OF LINTEL BAR

4
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12 100001172-50 TCWS54D2
74 3/4"
55 1/16"
Steel Stud Framing Kit Dimensions Kit
Minimum Combustible Framing Dimensions
NON-COMBUSTIBLE materials
must extend 12” above and 9 5/8”
to the sides of the framing edges.
NON-COMBUSTIBLE BOARD NOT
INCLUDED.
NON-COMBUSTIBLE BOARD
All other framing can be done with
conventional lumber
Non-combustible
Board Detail
12”
9 5/8”
12”
31 1/2"
44 9/16"
74 13/16"
81 11/16"
81 11/16"
115 9/16"
55 1/4"
74 13/16"
NOTE: FIREPLACE SHOULD BE IN ITS FINAL LOCATION BEFORE FRAMING
RANGE
23 11/16"
to
25 7/16"
RANGE
25 3/8”
to
26 7/8"
RANGE
1/32"
to
3 3/16"
11 3/4"
FRAMING
LINTEL
74 3/4"
Framing kit is supplied
with Fireplace
Must allow for
minimum 1/2 inch
gap for non-combustible
board and facing
NOTE: Fireplace should be in its final location before framing.
NOTE: Combustible framing must allow for sheetrock installation.

5
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12
100001172-50 TCWS54D2
Proflame 2 Control System
Hearth Extension
Recessed Installation
Up to 50 Feet
ON
REMOTE
OFF
PROGRAM
TOWN & COUNTRY
LUXURY FIREPLACES
Caution: This fireplace may be recessed up to a maxi-
mum depth of 4 1/2”. This recess must be constructed
from non-combustible material. The space between the
outside framing edge and the firebox must be completely
free of any obstructions or debris, and the window, with
trim fitted, must be able to move freely.
No building material is permitted to protrude past the
framing edges attached to the fireplace under ANY
circumstance.
Town and Country D2 Series fireplaces use the SIT
Proflame 2 control system.
This includes an elegant hand-held remote control
transmitter with an easy to read LCD display.
The fireplace also comes with a wall-mounted control
switch which allows for simple ON/OFF operation, or
can be linked with the hand-held remote control unit.
This switch has a battery powered back-up system
which allows operation during power outages. The
wall-mounted switch easily connects to any customer
supplied Home Automation System.
Caution: While a hearth extension is not required and
combustible flooring materials may be brought directly up
to the fireplace, many materials (such as wood flooring)
may not tolerate the radiant heat from this fireplace,
resulting in discoloration, shrinking and cracking. For this
reason, we suggest a non-combustible hearth that is no
more than 1” above the bottom of the fireplace. If material
is thicker, fireplace must be raised accordingly.
Caution: Hearth extensions thicker than 1” will
interfere with the window frame when opening.
LINTEL
Surface of hearth extension
may not be be more than 1
inch above the bottom of the
replace.

6
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12 100001172-50 TCWS54D2
Direct Vent
Roof Installation

7
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12 100001172-50 TCWS54D2
20'
10'
8'
6
40'
MAX.
4'
2'
48'
4' MAX.
'
18” MIN BEFORE ELBOW
Roof Termination Venting Chart
TCWS54.D2 Cad Drawing
Available at
www.townandcountryreplaces.com
CAUTION:
Under no condition should
combustible
material be closer than
1 3/4 inches from any part of
the vent pipe.
Only 45º elbows can be used
in this vent system.
Maximum number of
elbows is 2.

8
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12
100001172-50 TCWS54D2
M
K
I
A
V
G
G
H
A
J
V
G
A
B
C
A
V
V
A
V
B
F
B
L
V
E
V
V
V
D
B
B
Direct Vent Terminal Clearance
Direct Vent Terminal Minimum Clearances
Minimum clearances to the vent terminal must be maintained
as shown (See illustration to right & below). Measure
clearances to the nearest edge of termination hood.
(See pitch table below).
NOTE: Vent terminal must not be recessed
NOTE: LOCAL CODES OR REGULATIONS MAY REQUIRE
DIFFERENT CLEARANCES.
Terminal to sloped Roof Pitch Table
(minimum)
ft m
Flat to 6/12 1.00 0.30
Over 6/12 to 7/12 1.25 0.38
Over 7/12 to 8/12 1.50 0.46
Over 8/12 to 9/12 2.00 0.61
Over 9/12 to 10/12 2.50 0.76
Over 10/12 to 11/12 3.25 0.99
Over 11/12 to 12/12 4.00 1.22
VENT TERMINAL MINIMUM CLEARANCES
TO ADJACENT STRUCTURES
A= *12 inches (30 cm) min. Clearances above grade, veranda, porch, deck, or balcony
B= *12 inches (30 cm) min. Clearance to window or door that may be opened
C= 12 inches (30 cm) min. Clearance to permanently closed window recommended to prevent condensation on window
D= 30 inches (76 cm) min. Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (60 cm) from the
edge of the terminal
E= 30 inches (76 cm) min. Clearance to unventilated soffit
F= 6 inches (15 cm) min. Clearance to outside corner
G= 6 inches (15 cm) min. Clearance to inside corner
H= 3 feet (90 cm) min. *Not to be installed above a meter/regulator assembly within 3 feet (90 cm) horizontally from the center-line of the
regulator
I= *6 feet (1.8 m) min. Clearance to service regulator vent outlet
J= *12 inches (30 cm) min. Clearance to non mechanical air supply inlet to building or the combustion air inlet to any other appliance
K= *6 feet (1.8 m) min. Clearance to a mechanical air supply inlet
L= *7 feet (2.1 m) min. ^ Clearance above paved side-walk or a paved driveway located on public property
M= **30 inches (76 cm) min Clearance under veranda, porch, deck, or balcony
^ a vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and serves both dwellings*
** only permitted if veranda, porch, deck, or balcony is fully open on a minimum of 2 sides beneath the floor*
* as specified in CAN/CSA B149.1 Installation Codes, Note: local Codes or Regulation may require different clearances
* for U.S.A. Installations follow the current National Fuel Gas Code, NFPA54/ANSI Z223.1
AIR SUPPLY INLET
VENT TERMINAL GAS METER
AREA WHERE TERMINAL
IS NOT PERMITTED
FIXED
CLOSED
FIXED
CLOSED OPEN-
ABLE
OPEN-
ABLE
36"
See Roof
pitch table
48"
ADJACENT
24"
(91.5 cm)
(61 cm)
(122 cm)
STRUCTURES
OR FENCE

9
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12 100001172-50 TCWS54D2
Up to 66 feet
of vertical run
Up to 110 feet of run
plus six 90º elbows
Up to 3 feet below unit
Optional Power Vent
Power Vent Terminals
Direct Vent Terminals
Reach almost any room or commercial setting.
Optional Power Venting allows runs up to 110’ to
an outside wall or roof surface (maximum 66’ of
vertical run). Vent horizontally or vertically with up
to six 90-degree elbows, including runs up to 3’
below the fireplace.
The premium Power Vent fan runs quietly outside,
at the exterior terminal.
Roof Termination Flush Mount termination
Stainless Steel Standard Venting
Termination for Condo Installation
Standard Venting
Wall Termination
Standard Venting
Roof Termination
TCWS54.D2 Cad Drawing
Available at
www.townandcountryreplaces.com

10
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12
100001172-50 TCWS54D2

11
FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
021118-12
100001172-50 TCWS54D2

FOR REFERENCE ONLY. CONSULT MANUAL BEFORE INSTALLATION
For personal service pertaining to specific projects, contact:
Town & Country Architect Resource Planner
[e-mail]
www.townandcountryfireplaces.com
Phone: [phone]
2975 Allenby Road, Duncan, BC Canada V9L 6V8
© 2018 Copyright Pacic Energy Fireplace Products LTD
Reproduction, adaptation, or translation
without prior written permission is prohibited,
except as allowed under the copyright laws.