TownSteel e-Smart 6000 Series User manual

Town Steel
e-Smart 6 000 Series
Installation Guide
TownSteer

1
Package Content 2
Getting Started & Handing information 3
Door Preparation 4
Step 1 - Adjusting Deadbolt 5
Step 2 - Installing Deadbolt & Strike 6
Step 3 - Setting Tail Piece 7
Step 4 - Installing OutsideStep 4 - Installing Outside Assembly 8
Step 5 - Installing Backplate 9
Step 6 - Installing Inside Assembly 10
Step 7 - Installing Inside Cover 11
Exploded View 12
Troubleshoot 13
Table of Contents
YW1930

Package Content
Parts in the box
Inside Cover
Deadbolt Deadbolt Strike Deadbolt Armor Plate Dust Box
Outside Assembly
R
Y
O
U
Screw Packs Screw Packs Deadbolt & Strike Screws
Backplate Inside Assembly
Additional Parts Included
S
2
YW1930

Getting Started
Handing Information
Tools needed for lock installation
Phillips Screwdriver (Not included)
Note:
Do not use a power drill for installation of lock - it can damage the lock.
3
If hinges are on the left,
and the door opens inward
or outward it is a left
hand door (LH)
If hinges are on the right,
and the door opens inward
or outward it is a right
hand door (RH)
Flat-Head Screwdriver (Not included)
Hinges Hinges
YW1930

Door Preparation
Important:
Door stop is where
the door will stop when
normally operated.
The stop includes any
gasket, smoke seal, or
bumpers.
bumpers. The position
of strikes are to be
measured taking this
into account.
Prepare door and jamb per template provided. The backset is the
dimension from the edge of the door to the centerline of the lock.
YW1930

2³⁄” 2³⁄”
Step 1
Place the deadbolt in the door frame cutout and make sure the
cross shaped hub is centered. Otherwise, look below on how to
adjust the deadbolt by rotating the deadbolt face.
5
YW1930

Step 2
Position cross as shown
Install the deadbolt and faceplate and secure with 2 screws.
Install strike, strike security plate, and dust box. Secure with
4 screws.
Note:
During installation keep the door open. Do not use power tools
for assembly or you can potentially damage the door.
6
Deadbolt
Faceplate
Strike
Dust box
Strike
security plate
YW1930

Step 3
Horizontal
tailpiece
Vertical
tailpiece
Set the handing on the outside assembly.
7
YW1930

Step 4
Guide Post
Wire harness
Install the outside assembly. Route the wire under the deadbolt and
the tail piece through the cross. The two plastic guide posts should
go through the holes on both sides of the cross.
Note: A left hand (LH) lock will be depicted in the following guide. For right
hand install opposite. Make sure the deadbolt is extended.
8
Extended
deadbolt
YW1930

Step 5
Install the backplate using the Y and U screw packs. Route
the wire harness through the lower cutout. Secure with the 2 Y
screws on the top two holes. Remove the two guide posts and
secure with the 2 U screws.
9
Optional:
O-screw
pack
Route wire harness
Y-screw
pack
U-screw
pack
YW1930

Step 6
Set the handing on the inside assembly. Plug the wire into the
connector. Install the inside assembly using the S-screw pack.
10
S-screw
pack
Reset
Rotate slot on
inside assembly
to set handing.
LH shown.
(use flat-head
screwdriver)
Plug cable
into connector
YW1930

Step 7
IMPORTANT- After adding batteries, see programming manual on
SETTING THE HANDING before operating the keypad. Once the
handing has been set, install inside cover using the R-screw pack.
R-screw
pack
Reset
11
YW1930

Exploded view
12
Outside
assembly
Deadbolt
Backplate
Y screws
U screws
O screws
Inside
assembly
S screws
Inside
cover
R screws
Deadbolt
strike Deadbolt
armor plate
Dust box
YW1930

13
Troubleshoot
Problem Cause Solution
Keypad does not light up. Batteries are dead.
Keypad is locked out due to
amount of incorrect codes
Not fully plugged in wires or
pinched wires.
Replace batteries by removing
back cover.
Wait 60 seconds and try again.
Check wire connection.
Deadbolt does not fully extend. Strikes are not aligned. Adjust strikes. (See door
template)
Deadbolt is jammed and does
not extend or retract.
Handing was not set correctly
on outside assembly.
Deadbolt was not extended
during installation.
Set handing correctly on
outside assembly. (See Step 3)
Take lock off door and re-install
with deadbolt extended.
(See Step 4)
Keypad lights up but deadbolt
does not respond.
Handing has not been set on
the keypad
With deadbolt extended, press
0 followed by #. See Step 7.
YW1930
See programming manual

17901 RAILROAD STREET
CITY OF INDUSTRY, CA 91748
TOLL FREE: 877-858-0888
VISIT WWW.TOWNSTEEL.COM FOR
YW1930