Toyota 00016-00401 User manual

TOYOTA COROLLA 2011 - HANDS FREE BLU TOOTH
ITEM QTY DESCRIPTION
11INTERFACE MODULE
21INTERFACE RADIO/POWER HARNESS
31SYSTEM SWITCH
41MICROPHONE PACK
51HARDWARE BAG
62FOAM ADHESIVE STRIP
71QUICK GUIDE STICKER
81OWNER’SMANUAL
KIT CONTENTS
HARDWARE BAG CONTENTS
ADDITIONAL ITEMS REQUIRED FOR INSTALL
RECOMMENDED TOOLS
ALL MODELS
GENERAL APPLICABILITY
RECOMMENDED SEQUENCE OFAPPLICATION
* MANDATORY
ITEM QTY DESCRIPTION
1N/AELECTRICAL TAPE
2
3
4
SAFETY TOOLS
SPECIAL TOOLS
INSTALLATION TOOLS
FASTENER REMOVAL TOOL WIRE CUTTERS
TRIM REMOVAL TOOL
8 & 10-MM DEEP SOCKET
P OWER D RILL /D RIVER
SPECIAL CHEMICALS
ITEM QTY DESCRIPTION
1 12 WIRE TIES
21ADHESIVE FOAM PAD
31CONVOLUTED TUBING
Conflicts
Part Number: 00016-00401
Accessory Code: BT4
Factory Bluetooth System & JBL Audio
1. All Applications Requiring Removal of A Pillar
Completed Before Installation of Microphone.
Southeast Toyota Distributors, LLC
Page 1 of 7

PARTS IDENTIFICATION
1
3
2
4
ITEM QTY DESCRIPTION PART NUMBER
11INTERFACE MODULE 00016-00401-01
21INTERFACE HARNESS 00016-00401-02
31SYSTEM SWITCH 00016-00401-03
41MICROPHONE PACK INCL.IN ITEM 1
51HARDWARE BAG INCL.IN ITEM 1
62FOAM ADHESIVE STRIP INCL.IN ITEM 1
71QUICK GUIDE STICKER INCL.IN ITEM 1
81OWNER’SMANUAL INCL.IN ITEM 1
5
8
6
7
Southeast Toyota Distributors, LLC
Page 2 of 7

VEHICLE PREPARATION
1. REMOVE THE LEFT AND RIGHT RADIO TRIM PIECES BY PRY-
ING THEM LOOSE WITH A TRIM PANEL TOOL.FIGURE 1
2. REMOVE THE A/C VENT BY PULLING IT OUTWARD AND DIS-
ENGAGING THE CLIPS.FIGURE 2
3. REMOVE THE INSTRUMENT CLUSTER BEZEL AND INSTRU-
MENT CLUSTER BY REMOVING THE CLIPS AND PHILPS HEAD
SCREWS.FIGURE 3
4. REMOVE THE RADIO BY REMOVING THE FOUR (4) 10MM
BOLTS.FIGURE 4
NOTE: BE CAREFUL NOT TO PUT EXCESSIVE TENSION
ON THE RADIO CONNECTIONS WHEN PULLING OUT THE RADIO.
SUPPORT IT ON A PROTECTED SURFACE TO PREVENT ANY
DAMAGE TO THE CONNECTIONS OR THE DASH PANELS.
CAUTION: IT IS ADVISABLE TO DISCONNECT THE
NEGATIVE BATTERY CABLE FOR 3MINUTES BEFORE
BEGINNING INSTALLATION,TO AVOID UNINTENDED AIR
BAG DEPLOYMENT. NOTE AND RECORD ANY ANTI-
THEFT RADIO CODES PRIOR TO DISCONNECTING.
VEHICLE PREPARATION
FIGURE 2
FIGURE 1
FIGURE 3
Southeast Toyota Distributors, LLC
Page 3 of 7

INSTALLATION
FIGURE 4
MICROPHONE
1. REMOVE THE LEFT A-PILLAR BY PULLING IT AWAY FROM THE
CHASSIS (DISENGAGING THE CLIPS)AND TWISTING THE PLASTIC
TETHER CLIP WITH NEEDL-NOSE PLIERS TO FREE THE TETHER
FROM THE PANEL.FIGURE 5
2. ROUTE THE MICROPHONE HARNESS ALONG THE FACTORY
WIRING AND USE WIRE TIES TO SECURE IT AS SHOWN IN
FIGURE 5.
NOTE: TAKE CARE NOT TO SECURE THE HAR-
NESS TO THE AIRBAG OR ANY OF ITS COMPONENTS.
3. ROUTE THE MICROPHONE HARNESS DOWN THE PILLAR,
BEHIND THE DASH TO THE AREA BEHIND THE INSTRUMENT
CLUSTER,SECURING IT WITH WIRE TIES AND FOAM TAPE.
4. REPLACE THE A-PILLAR PANEL. PRIOR TO FULLY SEATING
THE CLIPS,CLEAN THE UPPER CORNER WITH THE SUPPLIED
ALCOHOL PAD AND MOUNT THE MICROPHONE AS SHOWN IN
FIGURE 6.
FIGURE 5
FIGURE 6
Southeast Toyota Distributors, LLC
Page 4 of 7

INSTALLATION
SYSTEM SWITCH
1. REMOVE THE LEFT SIDE SWITCH PANEL BY PULLING IT OUT-
WARD TO DISENGAGE THE CLIPS.FIGURE 7
2. REMOVE THE RIGHTMOST AVAILABLE KNOCKOUT BLANK
AND INSERT THE HANDS-FREE SYSTEM SWITCH WITH THE
SOLID ARROW FACING UP.FIGURE 8
3. ROUTE THE SWITCH HARNESS UP BEHIND THE LEFT VENT
PANEL TO THE AREA BEHIND THE INSTRUMENT CLUSTER. THE
END OF THE HARNESS SHOULD SIT NEXT TO THE END OF THE
MICROPHONE HARNESS. TIE THE HARNESSES TO THE FACTORY
WIRE LOOM WITH WIRE TIES AND FOAM TAPE.
INTERFACE MODULE
1. CONNECT THE MICROPHONE, SWITCH,AND RADIO/POWER
HARNESS TO THE INTERFACE MODULE AS SHOWN IN FIGURE
9. USE A PIECE OF THE SUPPLIED FOAM TAPE TO COVER THE
FUSE ON THE HARNESS AS SHOWN IN FIGURE 10.
2. MOUNT THE INTERFACE MODULE TO THE FACTORY WIRE
HARNESS BEHIND THE INSTRUMENT CLUSTER AS SHOWN IN
FIGURE 10. SECURE THE MODULE WITH WIRE TIES.
FIGURE 7
FIGURE 8
FIGURE 9
MICROPHONE
SWITCH
RADIO/PWR
FIGURE 10
Southeast Toyota Distributors, LLC
Page 5 of 7

INSTALLATION
RADIO AND REASSEMBLY
1. CONNECT THE MAIN INTERFACE POWER HARNESS CONNEC-
TORS TO THE FACTORY WIRE LOOM AND THE RADIO BY MATCH-
ING THE CONNECTORS. MAKE SURE ALL CONNECTIONS ARE
SECURELY SEATED.FIGURE 12
NOTE: AVC-LAN (12-PIN)CONNECTOR MAY
NOT BE PRESENT ON THE VEHICLE’S HARNESS. WIRE TIE
THIS CONNECTOR TO THE HARNESS UNCONNECTED,BUT
ALWAYS CONNECT THE AVC-LAN (12-PIN)CONNECTOR
INTO THE RADIO. IFAVC-LAN (12-PIN)CONNECTOR IS
PRESENT INTHE VEHICLE HARNESS,CONNECT TO THE MAIN
INTERFACE POWER HARNESS. IF ANY OTHER ACCESSORIES
ARE INSTALLED THAT CONNECT TO THE HEAD UNIT,THE
HANDS FREE SYSTEM SHOULD BE THE ACCESSORY THAT
PLUGS INTO THE RADIO FIRST.
2. REINSTALL ALL TRIM PANELS IN THE ORDER OF REMOVAL,
TAKING SPECIAL CARE TO MAKE SURE ALL HARNESSES AND
WIRING ARE PROPERLY SECURED. MAKE SURE HARNESSES ARE
NOT PINCHED OR BOUND BY TRIM PIECES. PLACE THE
OWNER’S MANUAL AND QUICK GUIDE STICKER IN THE GLOVE
BOX.
3. RECONNECT NEGATIVE BATTERY CABLE AND TORQUE TO
3FT LBS. RE-ENTER ANY THEFT DETERRENT INFORMATION,IF
APPLICABLE.
FIGURE 12
FIGURE 11
INTERFACE MODULE
Southeast Toyota Distributors, LLC
Page 6 of 7

TOYOTA COROLLA
HANDS FREE BLU TOOTH
Southeast Toyota Distributors, LLC
Page 7 of 7