Toyota ME4000 User manual

Toyota Yaris 2015 Frameless® EC Mirror w/ Compass & HomeLink®
Part Number: 00016-05463
Accessory Code: ME4000
Note: This accessory requires replacement A-Pillar clip
62217-52070 to complete the installation for this vehicle.
This accessory requires small wire harness cover
00016-05463-04 to complete the installation for this
vehicle.
Conflicts
Note:
Factory HomeLink
Kit Contents
Item #
Quantity Reqd.
Description
1
1
Frameless® Mirror w/Compass
& HomeLink®
2
1
Wire Harness Cover
5
1
Main Power Wire Harness
Hardware Bag Contents
Item #
Quantity Reqd.
Description
1
2
Red T-Taps
2
2
Red Spade Connectors
3
10
Wire Ties
4
3
Foam Tapes
5
2
Quick Reference Guides
Additional Items Required For Installation
Item #
Quantity Reqd.
Description
1
1
A-Pillar Clip (62217-52070)
1
1
Small Wire Harness
Cover (00016-05463-04)
Recommended Tools
Safety Tools
Safety Glasses
Special Tools
Installation Tools
Needle Nose Pliers
10mm Socket
Screw Gun
Torque Wrench-48inch lbs
(Car Battery)
T20 Torx Bit/Driver
Ratchet/Driver
#2 Phillips Bit
Nylon Tool
Wire crimping tool
Side cuts
Dark Towel/ Cloth
Special Chemicals
Service Part Numbers
Part Description
Part Number
Frameless® EC Mirror w/Compass
and HomeLink®
00016-05463-01
Main Power Wire Harness
00016-05463-02
Small Wire Harness Cover
00016-05463-04
A-Pillar Clip
62217-52070
General Applicability
Recommended Sequence of Application
Item #
Accessory
1
2
3
*Mandatory
Southeast Toyota Distributors, LLC.
Page 1 of 22
REV.D.8.12.15
Doc. 16.90.00 Business Partner: J79 PIO / DIO 08/18/15

Care must be taken when installing this accessory to ensure damage does not occur to the vehicle.
The installation of this accessory should follow approved guidelines to ensure a quality
installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Figure 1
1. Disconnect the negative battery cable.
Isolate the cable with protection in place.
See Figure 1.
Wait at least 90 seconds after
disconnecting the cable from the
negative (-) battery terminal to
disable the SRS system.
Southeast Toyota Distributors, LLC.
Page 1 of 21
REV.D.8.12.15
Toyota Yaris
Frameless® EC Mirror w/ Compass & HomeLink®

Figure 2
2. Remove the driver side visor holders. Turn
the holder clockwise approximately 45°
and pull it as shown in the illustration.
Detach the 2 claws and remove the visor
holder. See Figure 2.
Figure 3
3. Using a nylon tool, disengage the 4 clips.
Disconnect the connector. Remove map
light assembly. See figure 3.
Southeast Toyota Distributors, LLC.
Page 2 of 21
REV.D.8.12.15
Toyota Yaris
Frameless® EC Mirror w/ Compass & HomeLink®

Figure 4
4. Disengage the front LHA-Pillar garnish
clips. See figure 4.
Text in Illustration
*1 Front A-Pillar Garnish Clip
HINT: The front A-Pillar garnish clip
should remain between the front A-
Pillar garnish LHand the pillar.
Note: RH front A-Pillar garnish is shown
in figure 4. Use the same procedure for
the LH front A-Pillar garnish.
Figure 5
5.
Text in Illustration
*a Protective Tape
NOTE: Install a new A-Pillar
garnish clip when replacing A-Pillar
garnish at the end of installation.
A-Pillar clip 62217-52070 is not
provided in the mirror kit. This
item must be ordered separately.
Using needle nose pliers, turn the front LH
pillar garnish clip 90° and disengage it from
the front pillar garnish LH. This clip CAN
NOT be reused. DESTROY and DISPOSE
of clip. See figure 5.
Note: RH front A-Pillar garnish is shown
in figure 5. Use the same procedure for
the LH front A-Pillar garnish.
Southeast Toyota Distributors, LLC.
Page 3 of 21
REV.D.8.12.15
Toyota Yaris
Frameless® EC Mirror w/ Compass & HomeLink®

Figure 6
6. Disengage the 5 clips, 2 claws and guide to
remove the No. 2 instrument panel finish
panel. See figure 6.
Figure 7a
7. Disengage the 2 claws and remove the
outer mirror switch assembly/knock out.
See figure 7a and 7b.
Figure 7b
Vehicles without Switch-Remove knock out.
Southeast Toyota Distributors, LLC.
Page 4 of 21
REV.D.8.12.15
Toyota Yaris
Frameless® EC Mirror w/ Compass & HomeLink®

Figure 8
8. Pinch the cover, disengage the 2 claws and
separate the cover. See figure 8.
Text in Illustration
*1
Cover
While holding down the lock lever in the
direction of the arrow labeled A, slide the
mirror in the direction of the arrow labeled
B and remove it. See figure 8.
Text in Illustration
*1
Lock Lever
Figure 9a
9. Using side cuts, trim the original harness
back 22 inches from the end of the spade
connectors and ring terminal. Pull/Separate
the ground wire from the main power
harness approximately 6 inches. See figure
9a and 9b.
Figure 9b
Southeast Toyota Distributors, LLC.
Page 5 of 21
REV.D.8.12.15
Toyota Yaris
Frameless® EC Mirror w/ Compass & HomeLink®

Figure 10
10. Strip the main power harness ground wire
back 1/4 inch. Make sure to not damage the
wire strands. Using the new spade
connector provided, connect the black
ground wire. Make sure the wire and spade
connector have made a good connection
and crimp. See figure 10.
Figure 11
11. Strip the main power harness main power
wires back 1/4 inch. Make sure to not
damage the wire strands. Twist the two
stripped ends together. Using the new
spade connector provided, connect the
black and black/white tracer wires to one
connector. Make sure the wires and spade
connector have made a good connection.
See figure 11.
Southeast Toyota Distributors, LLC.
Page 6 of 21
REV.D.8.12.15
Toyota Yaris
Frameless® EC Mirror w/ Compass & HomeLink®

Figure 12a
12. Mount the Frameless® EC Mirror
w/Compass in reverse of original factory
mirror removal. Slide and attach the
rearview mirror assembly and tighten
mirror set screw with a T20 torx bit or
driver. DO NOT over tighten screw. See
figure 12a and 12b.
Figure 12b
Figure 13
13. Route the mirror harness to overhead
console opening using the precut notches
on the front of the headliner. See figure 13.
Do not use power tools to tighten
screw. Hands tighten only.
Note: Remove fingerprints, smudges, dirt, etc.
from mirror and windshield with glass cleaner.
Southeast Toyota Distributors, LLC.
Page 7 of 21
REV.D.8.12.15
Toyota Yaris
Frameless® EC Mirror w/ Compass & HomeLink®

Figure 14a
14. Install the 33mm-58mm wire harness
cover (SET part # 00016-05463-04) over
the wire harness. Seat the bottom of the
cover securely to base of the mirror.
Extend the top of the cover fully into the
headliner. See figure 14a and 14b.
Figure 14b
Figure 15
15. Connect the mirror harness to the mirror
main power harness. Make sure both
connectors are fully engaged. Wrap foam
tape around conectors. See figure 15.
Note: The 33mm-58mm wire harness
cover 00016- 05463-04 is not provided
in the mirror kit. This item must be
ordered separately.
33mm-58mm
Harness Cover
Southeast Toyota Distributors, LLC.
Page 8 of 21
REV.D.8.12.15
Toyota Yaris
Frameless® EC Mirror w/ Compass & HomeLink®

Figure 16
16. Secure the harness to the front center of the
headliner with one (1) piece of foam tape.
See figure 16.
Figure 17
17. Route mirror main power harness along
front edge of headliner towards the LH
vehicle A-Pillar. See figure 17.
Southeast Toyota Distributors, LLC.
Page 9 of 21
REV.D.8.12.15
Toyota Yaris
Frameless® EC Mirror w/ Compass & HomeLink®