Toyota PZQ60-00341 User manual

PARTS REQUIRED – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 1 of 10
PZQ60-00341 : SATELLITE NAVIGATION KIT
Description
Part No.
QTY
Head Unit
PZQ60-00345
1
Bolts (M5x8)
-
8
Cable ties
-
14
GPS Antenna
PZQ60-00260
1
GPS Antenna earth plate
-
1
Owner’s Manual
PZQ60-00346
1
PZQ60-00350 : PATCH HARNESS
Description
Part No.
QTY
Patch Harness
PZQ60-00350
1
PZQ60-00230 : PATCH HARNESS
Description
Part No.
QTY
Patch Harness
PZQ60-00230
1

1. PARTS REMOVAL – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 2 of 10
Step 1.
Remove the Audio Facia Panel.
Remove negative terminal of battery before
proceeding with installation.
When removing panels, take note of the
location of clips as shown in diagrams.
Unless otherwise instructed, have all
temporarily removed parts stored in a safe
location where no damage can occur.
Step 2.
Remove the Blanking Plate by
removing the 4 bolts. Remove the
Audio Side Brackets from the
Blanking Plate, and discard the
Blanking Plate.

2. GPS ANTENNA INSTALLATION – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 3 of 10
Step 1.
Peel the earth plate sticker, before
installing the GPS antenna on to the
earth plate.
Prior to installing the GPS Antenna Earth
Plate, ensure that the surface of the Earth
Plate has been cleaned using an alcohol
based cleaner.
To peel the sticker from the Earth Plate,
slice thinly the sticker label side of the Earth
Plate as shown then peel the cutting part of
the Earth Plate Sticker.
.
Step 2.
Install the GPS Antenna on to the
Earth Plate as shown.
Step 3.
Install the GPS antenna with the Earth
Plate on the flat surface behind the
Air Vent Duct as shown.
Cable tie any excess wire.

3. HEAD UNIT INSTALLATION – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 4 of 10
Step 1.
Attach brackets to Head Unit as
shown, using the M5x8 Bolts
provided.
.
DO NOT USE SELF-TAPPING SCREWS!
Using self-tapping screws on the Head Unit
will damage internal parts of the unit and will
render the Head Unit inoperable or un-
repairable.
Step 2.
Locate the vehicle connectors as
shown in the diagram.

3. HEAD UNIT INSTALLATION – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 5 of 10
Step 3.
Connect the connectors to the Head Unit as shown in the diagram below.
Head Unit Connection Schematic Diagram
Vehicle Harness:
No.
Description
Connector
1
Main connector
10 pin male
2
Rear speakers connector
6 pin male
3
Steering switch, speed and reverse signal connector
28 pin male
4
Rear camera connector
4 pin male
5
Radio antenna
-
Patch Harness:
No.
Description
Connector
6
Microphone connector
8 pin male
7
Steering switch, speed and reverse signal connector
28 pin male
8
Rear camera connector
24 pin male
9
GPS antenna
-

4. RE-INSTALLATION – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 6 of 10
Step 1.
Re-install all temporary removed parts. Ensure that all panels are correctly aligned and that no
gaps are present.
Step 2.
Reconnect the battery.
Note: When re-fitting battery post terminal clamp, torque to be between 2.9 – 7.8 Nm.
Step 3.
Check that all switches function correctly as per vehicle specifications. Check that the audio
controls of the steering wheel switches function correctly.
Note: The DCC may need to be fitted to vehicle in order to check operation of audio.
If so, please remember to remove DCC fuse (30A) after check is complete.
Step 4.
Place the Owner’s Manual inside the Glove Box.

5. SYSTEM CHECK – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 7 of 10
Step 1.
Turn the key to IG ON, and perform
the following system checks.
Rear Camera Display Check :
Shift the gear to REVERSE and check
the audio display screen.
•If the audio screen shows the rear
view: OK
•If the audio screen does not
change: NG. Check the
connection of connectors 3, 7, 4,
and 8 of the Head Unit Schematic
Diagram.
Step 2.
Microphone connection check:
Press “Phone” button.
If the audio screen shows
“There are no telephones paired. Add
one now?”
Press NO
Go to next check item (Step 3)

5. SYSTEM CHECK – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 8 of 10
If the audio screen shows
“Microphone not connected”
Check the connection of connectors
6 of the Head Unit Schematic
Diagram and repeat the checks.
Step 3.
Drive the vehicle for a few hundred
meters to an outdoors area, where
there will be no interference to the
GPS signal (i.e. not inside a building
or any other roof structure).
Stop the vehicle.
Enter Service Menu:
Enter the Service Menu screen by
turning the headlight illumination on
and off three times, whilst pressing
and holding down the AUDIO button.

5. SYSTEM CHECK – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 9 of 10
Step 4.
System Sensors Check
Press “Function Check / Setting”.
Step 5.
Press “System Sensors Check”.
Step 6.
Check that;
•GPS Status is “OK (3D)”. If not,
check the installation of the GPS
Antenna, including the connection
of connector 9 of the Head Unit
Schematic Diagram.
•SPD Pulse Count is more than 0
Pulses. If not, check the
connection of connectors 3 and 7
of the Head Unit Schematic
Diagram.

5. SYSTEM CHECK – C-HR SATELLITE NAVIGATION
C-HR │Dec ‘16 Onwards Issue: 2.0 │Date: July 2018 │Page 10 of 10
Step 7.
After all system checks have been
checked and rectified, press and hold
POWER button until the Head Unit
restarts.
Step 8.
End of Head Unit installation.