Toyota RUSH-20 User manual

Toyota RUSH-20 Installation Manual
Matters Needing Attention
Common Issues
All the pictures in this manual are for reference only. The pictures may differ from the actual ones,
but the installation method is the same.
For your convenience, please read the instruction manual of the product carefully before installation.
Please pay attention to protect the surface of your car and avoid scratching.
Please check regularly that all accessories connected to the car are tight to ensure safe use.
1. Bracket installation reverse: trunk door does not close properly
2. The bracket screw is not replaced as required: the door does not close properly, will damage electric
poles
3 .The ECU control box is not plugged in properly, loose: there is no force when opening or closing the
door or the anti-pinch force is heavy
4. Pole ball head, the circlip is not installed properly: the poles detach during use (check after installation)
5. The connector is not plugged in properly, it falls off: the function fails.
6. The electric suction lock is off center: the door cannot close, the door gap is large, and the tension is
tight, which causes the door to open loudly.
7. Installed in a new car for a long time without restarting the car, resulting in low power: door opening
or closing not functioning normally, need to restart the car
8. Adding more than 5 kg of soundproof cotton to the tailgate may affect the opening or closing door
force, add power to ECU control box.
9. Long press the tail door button for 3-5 seconds till you hear the "beep" sound - the sound is long,
loosen hand and push down the tailgate and will hear a "beep beep" sound, completing the
programming (the tailgate will not function normally in un-programmed state)
10. When the ball head is wrong, the non-aligned ball head can be rotated 360 degrees.
Qualified ball head circlip
The ball circlip has been opened, there
is risk of electric pole detaching after
installation. It needs to be repaired
before installation.
Passed QC circlip. Not passed QC circlip
The repair and installation method
of the circlip, the circlip is stuck in
the notch at the outer end of the ball
Correct electric pole mounting (the
circlip tightly mounted in the ball
head)
Incorrect installation, the spring is
springed up, there is a risk of disen
gagement, and it needs to be repair
ed in a timely manner.
Incorrect ball head installation (the
circlip does not stick to the ball head)
has the risk of being disengaged and
needs to be repaired immediately.

1. Remove the left support pole of the
original car
2. Remove the right support pole of the
original car 3. Remove the left upper ball head of the
original car
4. Remove the right upper ball head of the
original car
5. Install our left upper bracket and fix it
with our screw 6. Install our right upper bracket and fix it
with our screw
7. Remove the left lower bracket of the original car and install the
bracket of our company. Fix it with our company's screw. 8. Remove the right lower bracket of the original car and install
the bracket of our company. Fix it with our company's screw. 9. Installation of left and right electric pole is
completed
10. Draw electricity from the original car
driver compartment
11. Remove the trim board at the right side of the rear tail, find
the connection screw of the original car, and connect it to the
ground wire of our company.
12. Connect the central control wire to the
B-pillar
Pink color central
control

19. Install tailgate switch at rear tailgate
13. Wiring diagram
14. Remove the electric suction lock of the original car,
install the electric suction lock of our company and
fix it with screw
15. Plug in electric suction lock’s plug
16. Remove the lower lock ring of the original car,
install the lower lock ring of our company, and fix it
with our company's screw.
17. Fasten our motor 18. Hall wire, central control line and power cable are
inserted into our control box one by one according to
color.
20. Installation of tailgate control switch in
original car driver's compartment 21. Installation completed
After the installation is completed, you must set up the tailgate programming settings.
Make sure that the doors are closed in place.
(Raise the tailgate to the desired height, press the tailgate switch button, 3-5 seconds
will appear a "beep" sound, loosen hand, then press the tailgate button to close, the
tailgate is close in place, and there is a "beep" sound, that is, the tailgate programming
is completed)

Disclaimer
Height Setting
Solution to Electric Tail Door Failure
Button control mode
The related problems and losses caused by improper installation and use are not covered by our
company's warranty. Please read this manual carefully before use. Please store carefully after reading,
so that you can check it later. The picture is for reference only. The product is subject to the actual object.
1: Long press on tailgate button for three seconds to open or close door on the original car remote control
2: Press once on the open/close door button on the front switch.
Raise the tailgate to the desired height, press the tailgate switch button, 3-5 seconds will appear a "beep" sound, loosen hand,
then press the tailgate button to close, the tailgate is closed, and there is a "beep" sound, that is, the tailgate programming is
completed
Fault Phenomenon Troubleshooting
Whether the yellow center line connected properlyThe original car remote control did not work
Does not work after installation is complete
Tailgate do not close properly
The original car remote cannot close the door
The tailgate does not go up halfway
Whether the left and right brackets of the poles are reversed
Whether the control box cables is plugged in properly
Whether the bracket is fixed or replaced with our special screw
Whether there is any programming after installation. The first time you install
on the car, you need to program by using the tailgate button once.
Programming steps; open the door and press and hold the door button for three
seconds. When you hear a click, release the hand and press the button again.
The tail door will automatically close and programming is complete.
Whether the left and right brackets of the poles are reversed
Whether the control box cables plugged in properly
Whether the bracket is fixed or replaced with our special screw
There are two vinyls on the left and right sides of the original rear door.
If it is loose, it needs to be tighten.
Check if the positive power supply is connected to 12V-16V
Check if the power cord fuse is plugged in.
Check if the ground wire is connected