Toyota PC170-0K01A User manual

1
2
3
5
10
4
่
PART NAME
NO.
1 1PC170-0K01C
Q’TY
PART NUMBER
A
1.
6
8 9
7
PART NUMBER ุ
REMARK
APPLICABLE MODEL
-HILUX 2015 (D-CAB ONLY)
PC170-0K01A
Rev.#1 (Eng. 24-08-18)
INSTALLATION MANUAL BODY SIDE MOLDING
Thank you for your purchase of TOYOTA genuine “BODY SIDE MOLDING” This manual explains the procedure
for installation, Please read this manual before installation to ensure correct installation.
1. Clean Cloth
2. Adhesive Tape
3. Degreasing Agent
4. Scissor or Cutter
5. Heat Gun (when temperature is 15 ํC or Lower)
6. Laser Digital Thermometer
INSTALLATION TOOLS/MATERIALS INSTALLATION REQUIREMENTS
9
10
5 - 8
6 - 1
7 - 1
8 - 1
-1
-1
2 1
PC170-0K01F
3 1
PC170-0K01B
4
(Body Side Molding FR LH)
(Installation Manual)
C-LH (Template C-LH)
A (Template A)
B-RH (Template B-RH)
B-LH (Template B-LH)
C-RH (Template C-RH)
(Body Side Molding RR LH)
(Body Side Molding FR RH)
(Body Side Molding RR RH)1PC170-0K01D
Component Parts
Time to installation : 30 min.
1. Temperature Range : 15 ํ - 55 ํ C
2. Installation Force : 49N ±1N

CAUTION : 1. Perform the installation indoors where it is not subjected to dust. If the air temperature is 15 ํC
or lower, the adhesive strength will be reduced. In order to prevent such problems, use a heat
gun to warm up the installation surface of the vehicle and the double-sided adhesive tape to a
temperature between 15 ํC and 55 ํC before performing adhesion work. Failure to do this may
cause the product to drop off or peel off.
2. Using a degreasing agent, thoroughly wipe off dust and oil from the installation surface of
the vehicle. Failure to do this can result in reduced adhesive strength and cause the product to
drop off or peel off. Keep fire away from the vehicle when using a degreasing agent.
3. Avoid touching the double-sided adhesive tape when release liner is peeled away as this can
cause adhesive strength to decrease.
4. All sticker templates must be used before product installation. Failure to do this may cause
the product to drop off or peel off.
5. It is recommended that these parts are installed at installer chest height to ensure accurate
alignment of product.
6. Please do not remove the product once installation completed as this can cause the adhesive
strength to decrease.
7. Please do not allow your vehicle to get wet (car wash or left in rain) for at least 24 hours
after installation.
8. Please avoid driving car more than 90km/h for at least 24 hours after installation
9. If washing vehicle with high pressure washer, please ensure nozzle is greater than 50 cm from
product. Failure to do this may cause the product to drop off or peel off
Rev.01
2.

3.
Installation Method
1
2. Position of sticker template.
2.1 Attach sticker template on front and rear door by using edge of door as reference point and as show on fig 2.1
Rev.01
2.1
A
C-RH B-RH
AA
FR
1. Clean and degrease the shaded area using clean cloth
with degreasing agent as shown in Fig. 1
2
500mm 750mm
END of R
END of R
50mm
50mm
50mm
50mm
50mm
C-RH B-RH
FR

4.
3. Trial fit (do not remove release liner) and check position of parts on both front and rear door mouldings by
aligning them to the sticker templates.
3
AA A
5
B-RH
A
4
4. Starting with front door mould, completely peel off release liners 3. and 4. by about 5cm and fold it to outside.
Completely remove release liners 1. and 2 and discard.
1
3
2
4
A
1. 2.
4
2
1
3
C-RH B-RH
5. Place the front door mould onto door panel, aligning it to the sticker templates. Apply firm pressure to part in
position ① to door panel and then check level of part in the portion between sticker templates A. Apply firm
pressure to part in position ② to door panel.
Rev.01
FR
FR
NOTE: If vehicle door panels and door mouldings are not at the required temperature, heat up vehicle
door panels and door moulding.

5.
6
8. Repeat steps 1- 7 to install parts on the opposite side.
9. After installation around 5 min, try moving the part to check adhesive tapes are properly attached in all areas.
A
A
C-RH
8
1.
2.
Rev.01
FR
7FR
7. Open doors to full opening angle to ensure moulds do not interfere with body panel. Remove the remaining
release liners in the direction according to Fig. 7. Check all release liners have been removed as failure to do this
may cause the product to drop off or peel off. Then apply pressure force of 49N ±1N on all areas of the part
with double-sided tape. Failure to do so may cause product to drop or peel off. Remove all sticker templates.
6. Repeat Steps 4 and 5 for rear door mould.
! CAUTION : Must press all areas of double-sided tape with a force of 49N ±1N