TP-Link TR-966D User manual

TR-966D
10/100Mbps WDM Fiber Bridge
User's Guide

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice.
is a registered trademark of TP-LINK
Technologies Co., Ltd. Other brands and product names
are trademarks or registered trademarks of their respective
holders.
No part of the specifications may be reproduced in any form
or by any means or used to make any derivative such as
translation, transformation, or adaptation without permission
from TP-LINK Technologies Co., Ltd. Copyright @2006 TP-
LINK Technologies Co., Ltd. All rights reserved.
Table of Content
Package Contents........................................................................1
Introduction...................................................................................1
Features........................................................................................1
Network Cable Supported............................................................2
Appearance Indication.................................................................2
Installation Guide..........................................................................4
Appendix Specication.................................................................6

1
Package Contents
The following contents should be found in your box:
 One WDM Fiber Bridge
 One AC adapter
 This User’s Guide
 Warranty card
Introduction
The TR-966D product is 10/100Mbps WDM Fiber Bridge. By
deploying WDM technology (Wavelength Division Multiplexer),
only single-mode ber is needed to transmit and receive optical
Ethernet packets.
The TR-966D mediates between a 10/100Base-TX segment
and a 100Base-FX segment. It is primarily designed for large,
more high speed/bandwidth demanding workgroups that
require expansion of the fast Ethernet network.
Features

Compiles with 802.3u 10/100Base-TX and 100Base-FX
standard.

Provide two SC ber connectors and two RJ45 connectors.

2
3

Auto-detection of half/full duplex transfer mode for RJ45
port.
 Auto-negotiation of 10/100Mbps rate and Auto-MDIX for
RJ45 port.
 Fiber port only support full duplex transfer.

Extend ber distance up to 20km for ber port.

Easy-to-view LED indicators provide status to easily monitor
network activity.
 External power supply.
Network Cable Supported
The connectors and network cables supported by the TR-966D
are listed in the following:
 RJ45 port: Cat 5 Twisted-pair
 SC Fiber port: single-mode ber cable
Appearance Indication
1. Front Panel
The front panel of the TR-966D consists of several LED
indicators
T1_SPD
T2_SPD
F2_LINK/ACT
F1_LINK/ACT
POWER
T2_LINK/ACT
T1_LINK/ACT
10/100M Fiber BridgeWDM
TR-966D
TR-966D Front Panel
2. Rear Panel
The rear panel of the TR-966D consists of one AC power
connector, two 10/100Mbps RJ45 ports and two SC Fiber
interfaces.
POWER T1 F2
F1
T2
TR-966D Rear Panel
3. LED Indicators
This TR-966D has LED indicators which can provide a real-
time report. When you take a look at these indicators, you will
know what’s happening your network.

Power(Red): Lights when the adapter is properly plugged in.

T1_SPD/T2_SPD(Green): Light when the RJ45 port is
connected to 100Mbps device; When the port connect to
a 10Mbps device, the LED turns off.

4
5

T1_Link/ Act/ T2_Link/ Act(Green): Steady green
indicates that a valid link exists. Flashing green indicates
that the TR-966D is receiving or transmitting data from the
RJ-45 port.

F1_Link/Act/ F2_Link/Act (Green): Steady green
indicates that a valid link exists. Flashing green indicates
that the TR-966D is receiving or transmitting data from
the ber port.
Installation Guide
1. Conguration
In order to achieve the aim of effectively expanding a Fast
Ethernet network, you can use the TR-966D as the example.
2. Installation procedure:
A. Connect the TR-966D to 10/100Base-TX Device (Hub or
Switch).
 Make sure that the length of twisted pair cable (Category-
5) between 10/100Base-TX device and converter is not
longer than 100 meters.
 Connect one end of twisted pair cable to RJ45 jack on the
TR-966D and the other end of the cable to the cable to
the RJ-45 jack on the 10/100Base-TX device.
B. Connect t h e TR-9 6 6D to 100Base-FX D e vice
Connection.
Connect on (SC) end of a singl-mode ber cable to the SC
connector F1/F2 on the TR-966D and the other end of
the cable to 100Base-FX device.
C. Turn on the device.
Notes:
The WDM technology employs passive optic multiplexing,
thus multiplex the transmit (TX) and receive (RX) lines onto a
single ber. WDM technology is implemented in couples. For
example, one site uses the F1 ber port on the TR-966D, the
other site uses DEVICE A, the ber port on DEVICE A must be
1550nm/1310nm WDM ber; One site uses the F2 ber port on
the TR-966D, the other site uses DEVICE B, the ber port on
DEVICE B must be 1310nm/1550nm WDM ber.

6
Appendix Specication
General
Standard IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX/100Base-FX
Topology Star
Protocol CDMA/CD
Data Transfer
Rate
Ethernet: 10Mbps(Half Duplex);
20Mbps(Full Duplex)
Fast Ethernet: 100Mbps(Half Duplex);
200Mbps(Full Duplex)
Ports 2 10/100Mbps RJ-45 ports
2 SC Fiber ports
( F1: 1310/1550 nm Single- mode single Fiber
F2: 1550/1310 nm Single-mode single Fiber)
LED indicator POWER Power on
Each port RJ45 port:10/100Mbps Link/Act
and 100Mbps speed LED
Fiber port: 100Mbps Link/Act
Network
Medium
RJ45 port: Cat. 5 Twist-pair
SC Fiber port: single-mode ber cable
Max. Distance Twisted pair (Cat.5): 100m
Single-mode ber cable: 20km
Environmental and Physical
Power Power Adapter (9V, 0.8A)
Dimension(LxWxH) 122mmx76mmx24mm
Environment Operating temperature: 0ºC ~ 40ºC
Storage temperature: -20ºC ~ 70ºC
Humidity: 5% ~ 90% RH
71035589
TP-LINK TECHNOLOGIES CO.,LTD.
E-mail:[email protected]
Website:http://www.tp-link.com
Add:3/F.,Buiding R1-B,Hi-tech Industrial Park,Shennan Rd.,Shenzhen,P.R.China