TP-Link TL-SG105E User manual

Connection
7106506308 REV2.1.1
For more information, please visit our website: http://www.tp-link.com
Installation Guide
5/8-Port Gigabit Easy Smart Switch
TL-SG105E/TL-SG108E
PC
Ethernet Ports (1-8)
TL-SG108E
Power Adapter
For simplicity, we will take TL-SG108E for example throughout this Guide.
Note:
Configuration
Router
LAN PortWAN Port
Internet
PC
2.
1.
Using the conguration utility
Using the Web-based GUI
The switch is plug and play. To manage the switch, you can use the Web-based GUI
or the configuration utility.
The utility is provided on the resource CD and only supported on Windows now.
3. Double click the icon on the desktop, and the utility home page
displays a list of TP-LINK Easy Smart Switches on the local network.
Double click the switch that you want to configure. Next enter the
username and password (both admin) for it. Then use the utility to
configure the switch.
5.
For more details, see the User Guide and the Easy Smart Conguration
Utility User Guide on the resource CD.
Insert the resource CD into a computer connected to the switch.
The resource CD home screen will appear. If not, double click AutoRun.exe on
the resource CD. Then click Install Easy Smart Conguration Utility on the
home screen and follow the prompts to install the program.
Visit the Web-based GUI with the default IP address of the switch
http://192.168.0.1, and log in with admin as both user name and
password.Then configure the switch on the GUI.
2.
Prepare your computer with a static IP address 192.168.0.x ("x" ranges from
2 to 254), and a subnet mask 255.255.255.0.
1.
Make sure the switch that you want to manage is in the same subnet
as your computer. You can click to configure the switch IP address.
4.

LED Explanation
COPYRIGHT & TRADEMARKS
IEEE802.3i, IEEE802.3u, IEEE802.3ab,
IEEE802.3x, IEEE802.1p, IEEE802.1q
CSMA/CD
Ethernet: 10Mbps (Half Duplex)
20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex)
200Mbps (Full Duplex)
Gigabit Ethernet: 2000Mbps (Full Duplex)
10Base-T:
UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100
Ω STP (maximum 100m)
100Base-TX:
UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100
Ω STP (maximum 100m)
1000Base-T:
UTP category 5e cable (maximum 100m)
EIA/TIA-568 100ΩSTP (maximum 100m)
5/8 10/100/1000Mbps Auto-Negotiation RJ45 Ports
Power, 10/100M LED, 1000M LED
Store-and-Forward
Automatically learning, automatically aging
10Base-T: 14881pps/Port
100Base-Tx: 148810pps/Port
1000Base-T: 1488095pps/Port
10Base-T: 14881pps/Port
100Base-Tx: 148810pps/Port
1000Base-T: 1488095pps/Port
Standard
Protocol
Interface
LED indicators
Transfer Method
MAC Address Learning
Frame Filter Rate
Frame Forward Rate
General Specifications
Data Transfer Rate
Network Media (Cable)
Specifications are subject to change without
notice. is a registered trademark
of TP-LINK TECHNOLOGIES CO., LTD. Other
brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced
in any form or by any means or used to make
any derivative such as translation,
Do not use this product near water, for example,
in a wet basement or near a swimming pool.
Avoid using this product during an electrical
storm. There may be a remote risk of electric
shock from lightning.
transformation, or adaptation without
permission from TP-LINK TECHNOLOGIES
CO., LTD. Copyright © 2016 TP-LINK
TECHNOLOGIES CO., LTD. All rights reserved.
http://www.tp-link.com
SAFETY NOTICES
This is a class B product. In a domestic
environment, this product may cause radio
interference, in which case the user may be
required to take adequate measures.
CE Mark Warning
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally.
If the Power LED is not lit, please check as follows:
A1: Make sure the power adapter is connected to the switch with power
source properly.
A2: Make sure the voltage of the power supply meets the requirements of
the input voltage of the switch.
A3: Make sure the power source is ON.
Q1. The Power LED is not lit
It is recommended that you check the following items:
A1: Make sure that the cable connectors are firmly plugged into the switch
and the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet).
Q2. The Link/Act LED is not lit when a device is connected to
the corresponding port
Power
On: Running at 1000Mbps
Flashing: Transmitting/receiving data
1000M (Green)
On: Running at 10/100Mbps
Flashing: Transmitting/receiving data
10/100M (Yellow)
On: Power on
Off: Power off
Cautions
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0˚C~40˚C (32˚F~104˚F)
-40˚C~70˚C (-40˚F~158˚F)
10%~90% non-condensing
5%~95% non-condensing
Environmental and Physical Specifications
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/ TV
technician for help.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful
interference.
2) This device must accept any interference
received, including interference that may cause
undesired operation.
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
FCC STATEMENT