TrailFX T0002B User manual

www . T r a il F X . c om
Page 1of 3 Rev 010118
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
DO NOT OVER TORQUE.STANDARD OPERATING LOAD FOR TIGHTEN
BODY MOUNT NUTS & BOLTS VARIES FROM
45
TO
65
FOOT POUND.
30-60 min
[e-mail]
1 866 638 4870
POLISHED STAINLESS STEEL –LIMITED LIFETIME
POWDER COATED BLACK –3 YEARS
Cutting Not
Required
PARTS LIST:
Qty
Part Description
Qty
Part Description
1
Tail Light Guard for Driver Side
1
Tail Light Guard for Passenger Side
2
Mounting Bracket
2
M6 x 12 Nylon nut
4
ST4.2 x 25.4 Screw
2
M4 x 12 Phillips Screw
2
M6 Plastic piece
Driver/Left Taillight Guard
Passenger/Right Taillight Guard
Tail Light Guard
Part No. T0002B
Chevrolet Tahoe
Chevrolet Suburban
Cadillac Escalade
Fits:2007 - 2014
2007 - 2014
2007 - 2014
2007 - 2014
GMC Yukon / Yukon XL/Yukon Denali
Drilling Not
Required

www . T r a il F X . c om
Page 2of 3 Rev 010118
INSTALLATION PROCEDURE
Step 1. Open rear tail gate, remove existing screws and detach tail light assembly carefully.
Step 2. Insert (1) T bolt plate on the vehicle and attach (1) mounting bracket using -20 Hex nut and tighten. (Note: T bolt plate
should be aligned at top end of oval hole before tightening) See Fig #1. And Fig #2.
Step 3. Re- attach tail light assembly and install tail light guard using (2) #8x1 screw and (1) M6 x 12 screw, align and tighten as
desired. See Fig #3 (Driver side shown)
Step 4. Repeat procedures 3-4 on opposite side.
Driver side shown - repeat on passenger
Illustration ↓
Step 1 Step 2
Step 3
Bracket

www . T r a il F X . c om
Page 3of 3 Rev 010118
1. Hardware’s are not of correct size.
In GMC / Chevrolet truck model 2006 & up, customer needs to reuse the factory body bolts to install the bracket. If your vehicle is not
GMC / Chevrolet 2006 & up, ensure that holes are not partially covered with any plastic grommet or rust? If it is, remove the plastic
grommet & rust from the thread holes & re-try the installation.
2. Mounting Bracket are not getting Installed properly.
In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver /
Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.
3. Products are thumping / rattling after installation.
Ensure that all required mounting brackets / hardware’s are installed & tighten correctly. Suggest using white lithium / regular grease
between the metal to metal contact surfaces.
4. Side Bar is not aligning with vehicle / Step Pads are not aligning with vehicle doors.
Side bar may be interchanged or mounting brackets are not installed at the correct position in the vehicle. Refer Parts identification guide.
5. Missing / Excess Hardware.
Recheck hardware count as per the part list.
6. Product not installing properly.
Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.
Check out these other TrailFX Products!! www.TrailFX.com
Periodically check the product to ensure all fasteners are tight and components are intact.
Regular waxing is recommended to protect the finish of the product.
Use ONLY Non-Abrasive automotive wax. Use of any soap, polish or wax that contains an abrasive is detrimental and can scratch the
finish leading to corrosion.
Aluminum polish may be used to polish small scratches and scuffs for Stainless Steel finish.

Mild soap may be used to clean the product for both
Stainless Steel and Black finish.
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time
of purchase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of
fitness for a particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product
at our option, when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this
product voids the warranty. KAO’s liability is limited to repair or replacement of products found to be defective, and specifically
excludes liability for any incidental or consequential loss or damage.