TrailFX BR012T User manual

Visit www.trailfx.com or 1 [phone] for Warranty Information / Tech Support / Product Updates.
2021 Keystone Automotive Operations Inc. All Rights Reserved. 05/20/2022-R01 Page-1-4
APPLICATION: 2021- 2022 FORD BRONCO 2DR
Assembly, Installation, Operation and
Maintenance Instructions
SIDE ARMOR STEPS
Part Number:
BR012T
60 - 180 minutes
Dealer / Installer:
Provide a copy of these instructions to the end user of this product. These instructions
provide important operating and safety information for proper usage of this product.
Demonstrate the proper use of the product with the end user. Have the end user
demonstrate that they understand the proper use of the product.
End User:
Read
and follow all instructions included in this manual. Ask your Dealer / Installer for
assistance if you do not understand the proper use of the product. Never remove any
decals from the product. Failure to follow these instructions can result in injury or death.
WARNING
PARTS LIST
Qty Part Description Qty Part Description
1
Driver/Left Side Armor
8
10mm x 35mm Hex Bolts
1
Passenger/Right Side Armor
8
10mm x 30mm Hex Bolts
1
Driver/Left Front Mounting Bracket
8
10mm Lock Washers
1
Passenger/Right Front Mounting Bracket
24
10mm x 27mm OD x 3mm Flat Washers
1
Driver/Left Rear Mounting Bracket
8
10mm Nylon Lock Nuts
1
Passenger/Right Rear Mounting Bracket
TORQUE SPECIFICATION
Size Torque
10 MM 34.5 ft/lbs
FRONT
Passenger/Right
Sidebar
(1) Passenger/Right Rear
Mounting Bracket (1) Driver/Left Rear
Mounting Bracket
(1) Driver/Left Front
Mounting Bracket
(1) Passenger/Right Front
Mounting Bracket

Visit www.trailfx.com or 1 [phone] for Warranty Information / Tech Support / Product Updates.
2021 Keystone Automotive Operations Inc. All Rights Reserved. 05/20/2022-R01 Page-2-4
INSTALLATION PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY
BEFORE STARTING INSTALLATION.
2. Starting from underneath the Passenger/Right body panel, locate the front mounting location and the threaded holes in the
body panel, (Figure 1). Remove the plastic plugs covering the holes.
3. Select the Passenger/Right Front Mounting Bracket. Attach the Mounting Bracket to the front location with (2) 10mm x
30mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers, (Figure 2). Do not tighten hardware.
4. Repeat Steps 2 & 4 to attach (1) Rear Mounting Bracket to the rear location, (Figures 3 & 4). Do not tighten hardware.
5. Select the Passenger/Right Side Armor. Line up the mounting tabs on the Side Armor to the rear faces of the Mounting
Brackets. Attach the Side Armor to the Mounting Brackets with (4) 10mm x35mm Hex Bolts, (8) 10mm Flat Washers and
(4) 10mm Nylon Lock Nuts, (Figure 5). Do not tighten hardware.
6. Level and adjust the Side Armor and tighten all hardware.
7. Repeat Steps 1—6to attach the Driver/Left Side Armor.
8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may
be used also to clean Side Armor.
INSTALLATION IMAGES:
Passenger/Right Side Installation Pictured
(Fig 1) Passenger/Right front mounting
location
(Fig 2) Attach the Passenger/Right Front
Mounting Bracket to the front location
(Fig 3) Rear mounting location (Driver/Left
side shown)
Front
Front
(2) 10mm x 30mm Hex Bolts
(2) 10mm Lock Washers
(2) 10mm Flat Washers

Visit www.trailfx.com or 1 [phone] for Warranty Information / Tech Support / Product Updates.
2021 Keystone Automotive Operations Inc. All Rights Reserved. 05/20/2022-R01 Page-3-4
PRODUCT CARE
•Periodically check the product to ensure all fasteners are tight and components are intact.
•Regular waxing is recommended to protect the finish of the product.
•Use ONLY Non-Abrasive automotive wax. Use of any soap, polish or wax that contains an abrasive is detrimental and can
scratch the finish leading to corrosion.
•Mild soap may be used to clean the product for Black finish.
FAQ’s
1. Hardware and mounting brackets are not aligning properly
Ensure that hardware is being used on the correct side of vehicle. In some cases, the hardware may appear the same for driver and
passenger side but may alter the alignment of mounting location. Check mounting brackets for both sides.
2. Products are thumping / rattling after Installation
Ensure that all required mounting brackets / hardware’s are installed & tightened correctly.
Suggest using white Lithium / regular grease between metal-to-metal contact.
3. Missing / Excess Hardware
Recheck hardware count as per the part list.
4. Product not installing properly
Ensure the Year / Make / Model as well as cab and bed dimensions are correct for the application. Review all steps for installation to
ensure they were followed correctly.
5. Who should be contacted for questions regarding product / installation assistance?
www.trailfx.com / sup[email protected] or 1-[phone]
(Fig 4) Attach (1) Passenger/Right Rear
Mounting Bracket to the center location
(Fig 5) Attach the Passenger/Right Side
Armor to the Mounting Brackets
Front
(2) 10mm x 30mm Hex Bolts
(2) 10mm Lock Washers
(2) 10mm Flat Washers
(2) 10mm x 35mm Hex Bolts
(4) 10mm Flat Washers
(2) 10mm Nylon Lock Nuts

Visit www.trailfx.com or 1 [phone] for Warranty Information / Tech Support / Product Updates.
2021 Keystone Automotive Operations Inc. All Rights Reserved. 05/20/2022-R01 Page-4-4
Warranty Terms:
Black Powder Coated: 3 Year Limited Warranty
TrailFX and Keystone Automotive Operations Inc. make no guarantees or warranties for products not
manufactured by Keystone Automotive Operations Inc. Such products are covered solely under any
applicable warranty of the manufacturer. It is always recommended that the operating instructions and
warranty instructions provided by the manufacturer are followed.
KeystoneAutomotive Operations Inc. warrants its products to be free from manufacturing and material
defects to the original purchaser for the length of warranty stated above from the date of retail purchase.
If any products are found to have a manufacturing or material defect, the product will be replaced or
repaired at the option of TrailFX and KeystoneAutomotive Operations Inc. with proof of purchase by the
original purchaser. The original purchaser shall pay all transportation and shipping costs associated with
the return of the defective product and the defective product shall become the property of Keystone
Automotive Operations Inc.
The Warranty applies to KeystoneAutomotive Operations Inc. products used for individual and
recreational purposes. Commercial usage of the KeystoneAutomotive Operations Inc. products limits the
warranty to 90-days from date of purchase.
The Warranty applies only to Keystone Automotive Operations Inc. products which are found to be
defective in manufacturing or material. This warranty does not apply to normal wear and tear of the finish
placed on Keystone Automotive Operations Inc. products.
TrailFX and KeystoneAutomotive Operations Inc. are not responsible for any labor costs incurred for
removal or replacement of the defective product.
TrailFX and KeystoneAutomotive Operations Inc. are not responsible for repair or replacement of any
product under the limited warranty where the product was improperly installed, misapplied, altered,
abused, neglected, overloaded, misused or damaged as a result of an accident, including any use of the
product not in accordance with all product operating and safety instructions.
Without limiting the generality of the foregoing, TrailFX and Keystone Automotive
Operations Inc. shall under no circumstances be liable for any incidental or consequential loss or damage
whatsoever arising out of, or in any way relating to any such breach of warranty or claimed defect in, or
non-performance of the products. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusion or limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights that vary from
state to state.